GRASS VALLEY 6028 Series User manual

6028 Series
1U Control Panels
Quick Setup Guide

6028 Series Quick Setup Guide
2
LED Control Panels
6028000 (78-key High density Panel – configurable as a BPX or XY panel)
6028400 (60-key High density Panel – configurable as a BPX or XY panel )
6028100 (42-key Standard Density Panel – configurable as a BPX panel)
6028201 (24-key Standard Density Panel – configurable as a BPX panel)
LCD Control Panel
6028251
6028351
The LCD panels have a 64x32 pixel LCD on each key and a single rotary encoder. The LCD panels are
compatible with Aurora control systems.

6028 Series Quick Setup Guide
3
Configuration and Connection
Step 1: Select Control System
Control panel modes are set using DIP switch 6. See table below:
LCD Control Panel Modes
Note: Mode must match database configuration. A mismatch is not flagged – switches may still light and
control router crosspoints.
DIPSwitches 
5  6  7  8  9 
16WayBPX  Up  Up  Up  Up  Up 
Dual8SplitBPX  Down  Up  Up  Up  Up 
8x8X‐Y  Up  Down  Up  Up  Up 
16x4X‐Y(nolevelkeys)  Down  Down  Up  Up  Up 
32WayBPX  Up  Up  Down  Up  Up 
Dual16SplitBPX  Down  Up  Down  Up  Up 
16x16X‐Y  Up  Down  Down  Up  Up 
32x4X‐Y(nolevelkeys)  Down  Down  Down  Up  Up 
48WayBPX  Up  Up  Up  Down  Up 
Dual24SplitBPX  Down  Up  Up  Down  Up 
48x4X‐Y(nolevelkeys)  Down  Down  Up  Down  Up 
32x16X‐Y  Up  Up  Down  Down  Up 
Dual16+16BPX  Down  Up  Down  Down  Up 
16x16X‐Y  Up  Down  Down  Down  Up 
24x12X‐Y  Down  Down  Down  Down  Up 
UserDefined  Up  Up  Up  Up  Down 
Step 3: Connect Power
Plug cable into 2A fused IEC
socket
Step 1: Select Control System
LED control panel modes are set using DIP switches 5 – 9. See table below
LCD control panel modes are set using DIP switches 1
UP
=
6711 Mimic (BPX or Freeform)
Step 2: Select Comms Type
Set DIP switch 10:
UP = RS485 (serial)
DOWN = Ethernet
Step 4: Setup Comms
Connect the appropriate cable to a comms port (serial or Ethernet) and configure the port address
-Standard RS232/485 pinout Serial Cable
-Standard CAT-5 10/100 BASE-T straight-through or crossover Ethernet cable
Set DIP switches 5 – 9
According to the table to set
the control panel
DIP Switches

6028 Series Quick Setup Guide
4
Serial Comms Setup
Note: Multi-drop address must match database configuration.
Set DIP switches 1 and 2 down
to terminate long cable runs or the end
of a multi-drop chain.
Hex Switch 1 sets the multi-drop address:
Switch 1 2 3 4 5 6 7 8 9 A B C D E F 0
Address 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

6028 Series Quick Setup Guide
5
Ethernet Comms Setup
Note: IP address must match database configuration.
Change IP details from default values before connecting to a real network:
1. Using a PC configured to be on the same subnet as the panel default address, connect to the
panel.
2. Open a web browser, type the default IP address 192.168.1.1 and press Return.
3. In the Control Panel Setup screen that displays in the browser, type the new control panel IP address,
subnet mask, and gateway.
4. TypetheNucleuscontrollerIPaddressesandportnumbers.Controllerportnumbers must be greater
than 1024 (excluding 3000).
5. Click Submit Settings .
6. Click Reset Control Panel .
Key Brightness
Hex switch 2 sets the brightness of the keys.
0 = minimum brightness, through to
7 = maximum brightness
(switch settings 8 - F are not used)

6028 Series Quick Setup Guide
6
Contact Information
Grass Valley Technical Support
For technical assistance, contact our international support center, at
1-800-547-8949 (US and Canada) or [phone].
To obtain a local phone number for the support center nearest you, please consult the Contact Us section of
Grass Valley’s website (www.grassvalley.com).
An online form for e-mail contact is also available from the website.
Corporate Head Office
Grass Valley
3499 Douglas-B.-Floreani
St-Laurent, Quebec H4S 2C6
Canada
Telephone: [phone]
Fax: [phone]
www.grassvalley.com