Greenlee 7238SB SLUG-BUSTER Datasheet

Printed in U.S.A.
7238SB SLUG-BUSTER®PUNCH SET WITH RATCHETING WRENCH
PARTS LIST
CAT./UPC NO.
KEY 78-3310- DESCRIPTION QTY.
A 34941 Ratcheting 1" Box End Wrench 1
B 00042 3/8" Draw Stud 1
C 304AVBB/04042 3/4" Draw Stud 1
D 721-1/2/31756 1/2" Slug-Buster® Conduit Punch 1
D 14722 1/2" Conduit Die 1
E 721-3/4/31757 3/4" Slug-Buster® Conduit Punch 1
E 124AV/06972 3/4" Conduit Die 1
F 712-1/31758 1" Slug-Buster® Conduit Punch 1
F 126AV/04011 1" Conduit Die 1
G 721-1-1/4/31759 1-1/4" Slug-Buster® Conduit Punch 1
G 128AV/04013 1-1/4" Conduit Die 1
H 721-1-1/2/31760 1-1/2" Slug-Buster® Conduit Punch 1
H 440AV/04061 1-1/2" Conduit Die 1
I 721-2/31761 2" Slug-Buster® Conduit Punch 1
I 442AV/04063 2" Conduit Die 1
34758 Plastic Case 1
INSTRUCTIONS AND PARTS LIST
INSTRUCTIONS ET LISTE DES PIÈCES
INSTRUCCIONESY LISTA DE PIEZAS
7238SB SLUG-BUSTER®
1/2" Thru 2" Knockout Punch Set
with Ratcheting Wrench
7238SB SLUG-BUSTERmd
de 1/2 po à 2 po ensemble
de poinçon avec clé à rochet
7238SB SLUG-BUSTER®
1/2" a 2" equipo de perforadora
de impacto con llave de trinquete
Read and understand this material before operating. Failure to understand how to safely
operate the Slug Buster®set could result in an accident causing serious injury or death. This
tool should only be operated by qualified personnel.
Assurez-vous que vous avez lu et compris la documentation avant d’utiliser l’appareil. Si vous
necomprenezpascommentutiliserleSlugBustermd entoutesécurité,vouspourriezprovoquer
un accident entraînant des blessures graves, voire mortelles. Cet outil ne doit être utilisé que
par un personnel qualifié.
Leer y comprender este material antes de operar. La falta de comprensión acerca de cómo
operar con seguridad el equipo Slug Buster®puede ocasionar un accidente que cause lesiones
graves o muerte. Esta herramienta debe ser operada solamente por personal calificado.
999 9611.1 © 1996 Greenlee Textron IM-1067 Rev 4 9/96
A
B
F
DE
I
H
C
G
www. .com [e-mail]1.800.561.8187

7238SB SLUG-BUSTER®PUNCH SET WITH RATCHETING WRENCH
Do not punch enclosures containing or close to
live circuits. Electrical shock could result causing
severe injury or death.
• When hole is completed the punch unit (punch, die and draw
stud) can fall free toward the die side.
• Make sure you have firm footing and balance when operating.
Position yourself to avoid injuries in case of slippage, break-
age or any other loss of control while punching.
Lubricate threads and cutting edges before use.
CAPACITY: 10 ga. mild steel
5Disassemble punch by turning
draw stud counterclockwise
while holding punch. Tip die and
drop out split slugs.
6For 3/4" through 2" conduit
sized holes use 304AVBB 3/4"
draw stud. Place selected size
die on draw stud. Insert draw
stud in 3/4" or larger pilot hole.*
Thread same size punch on the
draw stud with the cutting edge
toward the material being
punched.
7Turn draw stud clockwise with
34941 wrench until material is
punched.
CAUTION: punch will become
free of hole and could fall.
8Disassemble punch by turning
draw stud counter-clockwise
while holding punch. Tip die
and drop out split slugs.
OPERATING INSTRUCTIONS — SAVE THESE INSTRUCTIONS!
1The 1/2" conduit size punch
requires 3/8" or larger pilot hole.
Use Greenlee Kwik Stepper
pilot step drills.
2Place 1/2" conduit die on 3/8"
draw stud. Insert draw stud
through pilot hole.
3Thread punch on draw stud with
cutting edge toward material
being punched.
4Turn draw stud clockwise with
the 34941 wrench until material
is punched.
CAUTION: punch will become
free of hole and could fall.
* Time Saver: Use 1/2" conduit
punch to make 7/8" pilot hole
for 3/4"-2" conduit punches.
www. .com [e-mail]1.800.561.8187