Greentouch Scott Living 1328VB-72-220 User manual

( 72-IN W x 22-IN D x 35-IN H)
72-IN Vanity Base and Top
Date Purchased _______________________
TM
Questions, problems, missing parts?
Before returning to your retailer,
call our customer service department at
1-855-571-1044 9 a.m. - 5 p.m., EST, Monday-Friday.
www.greentouchhome.com
Durham Bathroom Vanity

2500VT-72-906 72" Dark Gray Top with Backsplash
1328VB-72-220 72" Chocolate Finish Vanity Base & Sink
1328VB-72-236 72" Espresso Finish Vanity Base & Sink
1328VB-72-241 72" White Oak Finish Vanity Base & Sink
1328VB-72-242 72" Light Gray Finish Vanity Base & Sink
2500VT-72-900 72" Carrara Marble Top with Backsplash
2500VT-72-901 72" White Quartz Top with Backsplash
MODEL NUMBER DESCRIPTION
2500VT-72-904 72" Black Granite Top with Backsplash
2500VT-72-905 72" Terrazzo Top with Backsplash
2
TM

3
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
PACKAGE CONTENTS
SAFETY INSTRUCTIONS
Please read and understand this entire manual before attempting to assemble, operate or install the
product.
WARNING
• Some steps are more easily handled with 2 adults.
CAUTION
• Use care when assembling the vanity; take your time and follow the assembly instructions closely.
PART DESCRIPTION QUANTITY
A Vanity 1
B Top 1
C Backsplash 1
D Sink 2
E 2
F
Right Door
(preassembled
to Vanity (A))
2
Left Door
(preassembled
to Vanity (A))
G 2
H
Large Drawer
(preassembled
to Vanity (A))
Small Drawer
(preassembled
to Vanity (A))
2
JCenter Support
Leg 2
I 4
CARTON
Box 2 of 2
Box 1 of 2
Box 2 of 2
Shelf
KK
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
C
B
D
D
G
G
AI
H
H
E
F
E
F
J
Touch Up Pen
Qty. 1

4
INSTALLATION INSTRUCTIONS
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with
package contents list and hardware contents list. If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Installation Time: 45 minutes (24 hours for adhesive to dry).
Tools Required for Installation (not included): Phillips screwdriver, utility knife or scissors, adhesive,
power drill with drill bit, measuring tape, level
1. With 2 people, place the vanity on its back on
a flat, scratch free surface. Locate the Center
Support Legs (J) and screw into the base of the
vanity. Once complete, lift the vanity back up
into the upright position.
2. To remove small drawers (I)preassembled in
vanity (A). Fully extend drawers, locate plastic
levers on metal glide tracks at left and right sides
of drawer box, push on plastic levers on both
sides at the same time, to disengage drawer
box from the glides, Then gently lift the drawer
up to remove it from the glide tracks.
1
A
J
A
I
2

5
3. Clean area where the vanity (A) will be
permanently located prior to beginning
installation, ensuring the vanity (A) will not
interfere with any water supply and drain lines
once mounted.
Locate wall studs and mark locations. With the
help of another adult, place completed Vanity
Cabinet Assembly to its final location. Adjust
the height of the Vanity Cabinet (A) by
twisting the adjustable leveler foot pins on the
bottom of each leg. Twist clockwise to
decrease height or twist counter-clockwise to
increase vanity height.
Using hardware appropriate for your wall type
(not included), secure Vanity Cabinet (A) to
two wall studs anywhere through the Vanity
Mounting Plates. Be careful not to disturb
any electrical or water lines that may be
concealed in the wall.
INSTALLATION INSTRUCTIONS
4. Apply silicone adhesive to the top edge of the
wood cabinet. With the help of another adult,
gently lower the stone top with assembled sink
onto the cabinet. Make sure the stone top is flush
with the back side of the wood cabinet and the
stone overhang is equal on both sides over the
wood cabinet left and right side walls. Remove
any excess adhesive before allowing to dry.
Tip: it may be easier to install the faucet and/or
drain assembly (not included) before
securing the stone top to the wood cabinet.
3
Mounting
Plate
A
2
2
A
B
4
WARNING
Vanity (A) MUST be secured to the wall.