Greenway Home Products GWD9500W-POU User manual
Point-of-Use
Water Dispenser
Distributeur d’eau
au Point d’utilisation
Dispensador de Agua
a Punto de Utilización
GWD9500W-POU
GWD9500BLS-POU
Use & Care Guide
Guide d’utilisation
et d’entretien
Manual d uso y cuidado
REV01
Water Technologies
Water Technologies
Water Technologies
CAUTION: Before using water
dispenser, read this manual and
follow all safety rules and
operating instructions.
MISE EN GARDE: Avant
d’employer votre distributeur
d’eau, lisez ce manuel et suivez
toutes les règles de sécurité et
les consignes d’utilisation.
PRECAUCIÓN: Antes de usar
el dosificador de agua, lea este
manual y siga todas las reglas
de seguridad e instrucciones de
funcionamiento.
save These InsTrucTIons
conserver ces InsTrucTIons
guarde esTas InsTruccIones
Thank you for purchasing a Greenway®Water Dispenser. Please read the enclosed operating instructions carefully and
retain this booklet for future reference. We have carefully engineered your Greenway®Water Dispenser to give you years
of enjoyment and trouble free operation.
IMPORTANT NOTE: Your Greenway®water dispenser is designed with a special “safety” feature (float switch
mechanism) that controls activation/operation of the “Kettle Feature” hot water tank heating system. If no water is
present and/or low water levels are detected inside the internal reservoir system, activation/operation of the hot water
heating system is not possible. Likewise, if the hot water heating is operational and water is being drawn simultaneously
causing water levels to drop below safe levels, hot water tank operation is automatically terminated until normal water
levels are restored, at which time you must “manually” re-activate the hot water heating system by pressing the kettle
feature (red) button. NOTE: Operation of the cold water system is not affected by this safety feature.
IMPORTANT SAFEGUARDS
• Thiswaterdispenserisdesignedfor“indoor”useonly.DONOTUSEOUTDOORS.
• Neverturnthedispenserupsidedownortiltmorethan45degrees.Duringtransportation,ifthedispenserwas
transported in a “prone” (sideways) position, the unit must be left to stand upright for 12 hours before connecting to
power source and initiating operation.
• Thiswaterdispenserisequippedwithagroundedpowercordandplugforyoursafety.
• Keepyourwaterdispenserinadryplaceawayfromanyheatsourceanddirectsunlight.
• Neverputanythingammableclosetothedispenser.
• Leaveaminimumof2”(5cm)aroundthebackandsidesofthedispenserforproperventilation.
• Alwaysinstallyourwaterdispenseronalevel(solid)oor.
• Wait3minutesbeforerestartingmachineaftershuttingitdown.
• Alwaysunplug(disconnect)thewaterdispenserpowercordbeforeservicing,cleaningandlterreplacement.
• Servicemustbeperformedbyqualied/authorizedservicepersonnelonly.Serviceinformationisavailablethrough
ourCustomerServiceDepartmentat1-866-253-0447.
• Regularcleaningofyourwaterdispenserisrequiredforyourwarranty.
• Pleasefollowthecleaningandmaintenanceinstructionsoutlinedinthismanual.Cleaningshouldbedoneevery
4~6months.
• Itisyourresponsibilitytoensurethatallwaterlineconnectionsareproperlyconnectedandsealedand
there are no system water leaks before operating the unit.
• Althoughthisunitincorporatesprovisionofa(hotwater)“childresistantsafetyswitch”,neverallowchildrento
dispense hot water without proper and direct supervision.
DANGER:Thehotwaterinthisdispenserisheatedtoapproximately90°C(194°F).Temperaturesabove52°C
(125°F)cancausesevereburnsfromscalding.
• Onlyuseoriginal(OEM)Greenway®(VSRF-9)replacementlterswiththisunit.
GROUNDING INSTRUCTIONS
•Improperuseofthegroundingplugcanresultinariskofelectricshockcausingseriousinjury,evendeath.
•Thisappliancemustbegrounded.Intheeventofanelectricalshortcircuit,groundingreducestheriskofelectric
shock by providing an escape wire for the electric current.
•Thisapplianceisequippedwithapowercordhavingagroundingwirewithagroundingplugandmustbe
connectedintoaproperlygroundedpolarizedoutlet.Consultaqualiedelectricianifthegroundinginstructionsare
not completely understood, or if doubt exists as to whether the appliance is properly grounded. If the wall outlet is a
standard 2 prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded
3-prongwalloutlet.
• Donotunderanycircumstancescutorremovethethird(ground)prongfromthepowercordplug.
•Donotuseanadapterplugwiththisappliance.
• Donotuseanextensioncordwiththisappliance.Ifthepowercordistooshort,haveaqualiedelectricianinstall
an electrical outlet near the appliance.
YOUR GREENWAY®WATER DISPENSER
1. Top Cover
2.Ready-To-Dispense indicator lights:
Yellow: “flashing” Low water level inside internal reservoir. Hot water heating system cannot be activated.
(you must replenish water supply)
“off” Internalreservoirwaterlevelissufcienttoactivatehotwaterheatingsystem
Blue: “on” The cold water has reached optimum temperature and is ready for dispensing
“off” The cooling cycle is in progress, it is possible to dispense water during the cooling
cycle, however, optimum cooling temperature may not yet be achieved
3. Child resistant safety switch
4. Hot water dispensing button (also dispenses
room temperature water when Kettle feature is
not activated)
5. Cold water dispensing button
6. Kettle Feature (on/off) activation button
(self-illuminated)
“flashing” Heater (hot water tank) is operational.
“on” The hot water has reached optimum
temperature and is ready for dispensing.
“off” Heater (hot water tank) is off,
however remaining water within the tank
may still be very hot, always exercise caution
when dispensing and/or draining water from the
hot water tank.
7. Removable drip tray
8. Adjustable COLD water thermostat
(rear of dispenser)
9. Drain valve (rear of dispenser)
10. Condenser coils (rear of dispenser)
11. Lowerfrontpanel(lterlocatedbehind)
12. Manualshut-offvalve(waterinlet)
1
LH
3
11
7
62
5
10
8
12
9
4
1
It is highly recommended to have your water dispenser installed by a professional (licensed) plumber. If you are
installing the water dispenser yourself, the following information is important:
Depending on the type of plumbing in your home, (copper or flexible pipe) the following plumbing installation accessories
(notincludedwiththewaterdispenser)willberequiredtocompletetheinstallationofyourwaterdispenser.Theseitems
can be purchased at your local hardware store.
• ½”CopperTee(A)
• ½”MaleSolderx¼”ODCompressionFittingShutOffValve(B)
• InstallationAppearance(C)
• SolderingFlux
• Solder
• EmeryCloth
• Tube/PipeCutter
• WeldingTorch
• Towels(waterclean-up)
• ½”x½”x½”Quick-GripTee(D)
• ½”Quick-Gripx¼”ODCompressionFittingShutOffValve(E)
• InstallationAppearance(F)
2
(A) (B) (C)
(D) (E) (F)
InstallatIon In s t r u c t I o n s
Copper Pipe Plumbing (Soldering Required):
Flexible Pipe Plumbing (No Soldering Or Glue Required :
Tools Required:
• PlasticPipe/TubeCutter
Selectasuitablelocationwherethewaterdispenserwillbeinstalled,(inyourhome/kitchen)makingsureyouhaveeasy
access to an electrical wall outlet and cold water supply line.
1. IMPORTANT: Turn off the cold water supply.
2. Open the cold water faucet allowing water to purge the system (to minimize water leakage clean-up).
3. Usingatube/pipecutter,cutandremoveasectionofthecoldwaterlineatthedesiredheight(cutshouldbemade
above any manual shut-off valve installed on the water line).
4. COPPER PIPE PLUMBING:Usingemerycloth,cleanbothendsofthecopperpipesandapplyuxto“all”
surfaces to be soldered including the inside of the tee. Follow manufacturer’s installation instructions provided with
the½”MaleSolderx¼”ODCompressionFittingShutOffValve(B).
5. FLEXIBLE PIPE PLUMBING:Followmanufacturer’sinstallationinstructionsprovidedwiththe½”x½”x½”
Quick-GripTee(D)and½”Quick-Gripx¼”ODCompressionFittingShutOffValve(E).
6. Closethenewlyinstalledshut-offvalve(SeeFig.1AandFig.1B)andslowlyre-openthecoldwatersupplyline
and check for leaks. If leaks are detected, immediately close the water supply and repair any/all leaks. If no leaks
aredetected,proceedtostep7.
7. Thewaterdispenserincludes8meters(26feet)of¼”ODexiblewaterline.Ifadditionalwaterlineisneeded,it
canbepurchasedatyourlocalhardwarestore.Cutthedesiredlengthtosuityourinstallationrequirements,
makingsurebothendsofthewaterlinearecutstraight/square(SeeFig.1&Fig.2).Removethecompressionnut
andcompressionringfromthevalveandinstallonthewaterline(SeeFig.3).
3
Fig. 1A (Valve Open) Fig. 1B (Valve Closed)
Fig. 1 (Correct) Fig. 2 (Incorrect) Fig. 3
Get tI nG st a r t e d (Ma I n Wa t e r lI n e Ho o k -up):
Tools Required:
Installation Location:
Insertthewaterlineintothevalveuntilisstops(SeeFig.4)slideboththecompressionnutandcompressionringtoward
thevalveandtightenthenutrmlyusingawrench.CAUTION: DO NOT OVERTIGHTEN (See Fig. 5).
8. Thewaterdispenserisequippedwithamanual“shutoff”valveinstalledontherearsideofunit(SeeFig.6A)for
easy access in case of an emergency. Note: The orientation (installation position) for the shut-off valve may vary
depending on your model (i.e. horizontal or vertical), but the water line installation procedure for either version is the
same.(Seestep#9).
9. Connecttheincomingwaterlineintotheopensideofthemanualshutoffvalve(SeeFig.6B).Thisvalveutilizes
“quick-connect”typewaterlinettings(notoolsrequired).Simplyinserttheendofthewaterlineinto
the shut off valve and until it stops. WARNING: DO NOT OPEN THE WATER SUPPLY LINE AT THIS STAGE.
(SeeinstallationofFilter).
10. Todisconnect(remove)thewaterlinefromtheshut-offvalve,youmustrstremovethebluelocking“c-clip”
(SeeFig.14)bypullingitforward.
11. Toreleasethewaterline,simplypressandholdthe“white”outercollarsurroundingtheline(SeeFig.15)whileat
the same time pulling the water line out. NOTE: The locking “c-clips” must always be installed “prior” to installation
of the water lines.
Forhygienepurposes,thelterincludedinsidethewaterdispenserhasnotbeenfactoryinstalled.Ithasbeenshipped
initsoriginalshrink-wrappedpackage.Thelterislocatedbehindthelowerfrontpanelofthedispenser.Toaccessthe
lter;
• Removethedriptraybypullingitforward.(SeeFig.7)
• RemovethePhillipsscrewsecuringthelowerpanel.(SeeFig.8)
• Thelterissecuredby2retainingclips.Remove,andunwrapthelter.(SeeFig.9&9A)
4
Fig. 4 Fig. 5 Fig. 6
A
B
Fig. 7 Fig. 8
Fig. 9 Fig. 9A
InstallatIon offI lt e r :
• Toattachtheltertothelterhead,makesurethe“bluelockingtab”onthefrontoflterheadispushedalltheway
up(SeeFig.10).
• Screwthelter(1/4turnclockwise)intothelterheaduntilitstops.Pushdownthe“bluelockingtab”intothe
lockedposition(SeeFig.11)Ifthelockingtabfailstoengage,(lock)thelterisnotsufcientlytightened
(Re-tighten).
• The“redarrow”onthelterheadidentieswaterowdirection(in/out)throughthelter.
• Theinstallationisnowcomplete.Aswithallplumbinginstallations,thewatersupplyshouldbeturnedonslowly
and all connections should be inspected for leaks prior to opening all water valves fully. If any leaks are detected,
immediately close the water supply and repair.
• Todisconnect(remove)thewaterlinesfromthelterhead,youmustrstremovethebluelocking“c-clip”(See
Fig.14)bypullingitforward.
• Toreleasethewaterlinefromthelterhead,simplypressandholdthe“white”outercollarsurroundingtheline(See
Fig.15)whileatthesametimepullingthewaterlineout.NOTE:Theselocking“c-clips”mustalwaysbeinstalled
“prior” to installation of the water lines.
5
Fig. 10 Fig. 11
Fig. 13 Fig. 14 Fig. 15
UNLOCKED LOCKED
6
Thiswaterdispenserisequippedwithalowvoltagewaterleakagedetection
systemlocatedinsidethebaseoftheltercompartmentandiscoveredbya
removabledriptray(SeeFig.16).Intheeventanywatermakescontactwith
the leakage detection system, an audible alarm will sound (beep) continuously
untilthewaterisremoved.Uponactivationoftheleakagedetectionsystem,the
water inlet solenoid valve (located internally) is automatically (closed) deactivated
suspending incoming water activity until the alarm is silenced. To silence the
alarm, any/all accumulated water surrounding the sensors, must be removed
using a sponge and/or paper towels. The water inlet solenoid valve (opens)
reactivates automatically once the alarm is silenced.
Foroptimumwaterefciencyandperformance,werecommendreplacingthelterevery6months.Replacementlters
canbeorderedbycontactingourCUSTOMERSERVICEDEPARTMENT(TOLLFREE)AT1-866-253-0447ORYOUCAN
ORDERON-LINEAT;www.greenwaywt.com/shopping.ReplacementFilterpartnumberisVSRF-9.
CAUTION: Always turn off the water supply, using manual shut-off valve located at the rear of the dispenser, before
replacinglter.Thiswilldepressurizethewaterlineandminimizewateroverspraywhenthelterisreleased.Remove
andemptydriptrayunderlterofanyaccumulatedwater.Iftheaudiblealarmsounds,referto“WATERLEAKAGE
DETECTIONSYSTEM”instructions.
Likemostappliances,yourwaterdispenserrequiresperiodicmaintenance
formaximumefciencyandperformanceandmustbecleanedonaregular
basis,(coincidewithlterreplacementi.e.every6months)inordertomaintain
a hygienic environment and prevent potential formation (growth) of bacteria. A
cleaningkitisavailablethroughourCustomerServiceDepartmentat1-866-
253-0447orcanbeorderedonlineatwww.greenwaywt.com/shopping,oryou
canpre-mixasolutionof15ml(1tbsp)bleachwith4.5L(1.2gal)ofhotwater.
1. Always disconnect (unplug) the power cord before attempting any
cleaning,maintenanceandlterreplacement.
2. Always turn off the water supply, using manual shut-off valve at the rear
ofthedispenser,beforeattemptinganycleaning,maintenanceandlter
replacement.
Fig. 16
Fig. 17 Fig. 17A Fig. 17B
Cleaning Kit
Available online at
www.greenwaywt.com
Trousse de nettoyage
Accessible en ligne à
www.greenwaywt.com
Juego de limpieza
Disponible en línea en
www.greenwaywt.com
Water Leakage Detection System:
Filter Replacement:
InItIal pr o d u c t cl e a n I n G :
7
3. Toaccessthereservoirsystem,youmustremovethetopcoveronthedispenser(SeeFig.17)byremovingthetwo
Philipsscrewslocatedattherearofthecover(SeeFig.17A).
4. Carefully lift off the top cover.
5. Removetheblackreservoircoverbycarefullypullingupward(SeeFig17B).
6. If using a Greenway®water dispenser cleaning solution, please follow the manufacturer’s instructions provided with
thecleaningkit.Ifusingapre-mixedsolutionof15ml(1tbsp)bleachwith4.5L(1.2gal)ofhotwater,llthereservoir
and let stand for 20 min.
7. Press both dispensing taps until the cleaning solution stops flowing (collect the cleaning solution into a container/
bucket).
8. Flush the reservoir with clean water and press both dispensing taps until
water stops flowing (collect the water into a container/bucket).
9. To drain any remaining water from the reservoirs, remove (unscrew) the
draincapandpluglocatedattherearofthedispenser(SeeFig.18).
Collectthewaterintoacontainer/bucket.IMPORTANT:Rememberto
re-installthedraincapandplugandtighten(SeeFig.18).
10. Re-installthereservoircoverbypressingdownrmly.
11. Re-install the dispenser top cover and secure using the two Philips screws.
12. Re-connect the power cord.
13. Re-open the manual shut-off valve (you will hear water entering the system
which will stop automatically when the appropriate water levels are reached).
14. Place a container under the water spigots and press both dispensing buttons (separately) to make sure water is
flowing normally from each side.
IMPORTANTNOTE:YourGreenway®water dispenser is designed with a special “safety” feature (float switch mechanism)
that controls activation/operation of the “Kettle Feature” hot water tank heating system. If no water is present and/or low
water levels are detected inside the internal reservoir system, activation/operation of the hot water heating system is not
possible. Likewise, if the hot water heating is operational and water is being drawn simultaneously causing water levels
to drop below safe levels, hot water tank operation is automatically terminated until normal water levels are restored,
at which time you must “manually” re-activate the hot water heating system by pressing the kettle feature (red) button.
NOTE: Operation of the cold water system is not affected by this safety feature.
DO NOT ALLOW CHILDREN TO USE THE HOT WATER DISPENSING
BUTTON WITHOUT PROPER AND DIRECT SUPERVISION.
To prevent hot water from being dispensed accidentally and possibly harming
a child, the hot water dispensing button can only be operated when the child
resistant safety switch is activated. To dispense hot water, push/hold the child
safety switch sideways (in the direction of the arrow located on the switch)
from right to left, then press/hold the hot water button (as soon as water starts
flowing you can release the child safety switch) until the desired amount of hot
waterisdispensed.Uponreleasingthehotwaterbutton,thechildsafetyswitch
automatically re-engages to the locked position.
Fig. 18
L H
Child
resistant
safety
switch
Child Resistant Safety Switch:
op e r a t I n G In s t r u c t I o n s :
8
WARNING: The hot water is heated to approximately 90°C (194°F). Temperatures above 52°C (125°F) can cause
severe burns from scalding. DO NOT ALLOW CHILDREN TO USE THE HOT WATER DISPENSING BUTTON
WITHOUT PROPER AND DIRECT SUPERVISION.
The “Kettle Feature” (hot water) dispensing system on this unit is designed to save energy
andmoney.Conventionalhotwaterdispensingsystemsoperate24/7regardlessofwater
usage. The on demand “Kettle Feature” activates the hot water system ONLY when the “Kettle
Feature”(red)buttonisactivateddeliveringsteaminghotwaterinlessthan3minutes.
To stop/cancel the “Kettle Feature” during a cycle, simply press the “Kettle Feature” (red)
button a second time and the red LED light will turn off.
1. Press the “Kettle Feature” (red) button and the red LED light will start flashing to signify the heating system is
operational.Theheatingcycletakesapproximately3minutes.Whentheheatingcycleiscompleted,theredLED
light will change from “flashing” to a steady “on” condition (meaning water has reached optimum temperature).
2. To dispense hot water, place cup/glass under dispensing spigot, push/hold the child safety switch to the left and
press the hot water dispensing button (with red line indicator), until the desired amount of water is dispensed. The
red LED light will turn off automatically when the hot water is dispensed. NOTE: The hot water temperature (factory
default setting) is not adjustable on this unit.
The cooling system on this unit is designed to activate automatically as soon as the power cord is connected.
1. When the blue LED light is “off” the cooling cycle is operational. When the blue LED is light is “on” the cooling cycle
(compressor) is off and the cold water has reached optimum temperature.
2. To dispense cold water, place cup/glass under dispensing spigot, push/hold the cold water dispensing button (with
blue line indicator) until the desired amount of water is dispensed.
The temperature of the cold water reservoir is controlled by a cooling thermostat
located at the rear of the dispenser. The factory default setting of the thermostat
is “mid-point” (medium) on the thermostat scale. By turning the thermostat set
screw(SeeFig.19)thetemperaturecanbeadjusted.Turnthedialclockwise
(using a screwdriver) between “L” (warm) and “H” (colder) until the desired
temperature is reached. If water is not being properly dispensed, there could be
possible ice build-up in the reservoir due to the thermostat being set too cold.
If this happens, slowly rotate the dial counter clockwise to a warmer setting.
See“InitialProductCleaning”andfollowsteps1~13.
To remove, pull the drip tray towards you. Drain and clean. The drip tray should
be emptied and cleaned regularly to remove spotting and mineral deposits.
Clean with Greenway®water dispenser cleaning solution or mild soap and water
mixture. For tough deposits, add vinegar and let soak until the deposits come
loose. Then wash, rinse and dry throroughly. Put the grill back on the tray and
install on the dispenser.
Fig. 19
grill
drip
tray
Dispensing Hot Water:
Dispensing Cold Water:
Adjusting the Temperature (Cold Water Only):
cl e a n I n G a n d Ma I n t e n a n c e :
Cleaning the Drip Tray (Not Dishwasher Safe):
9
The outside of the dispenser can be wiped clean with a Greenway®water dispenser cleaning solution or a mild soap and
water mixture. Never use harsh chemicals or abrasive cleaners. Rinse thoroughly with clean water and then dry surfaces.
Vacuum or sweep away the dust from the condenser coils at the back of the dispenser. For best results, you can
purchaseabrushdesignedspecicallyforthispurposefromyourlocal
appliancestore.Thiswillimprovecoolingandefciency.
The internal (cold tank) reservoir incorporates a water overflow flotation device.
(SeeFig.20)
“A” is the “primary” flotation device that manually controls incoming water and related water levels associated with
normal operating conditions. The design parameter of this device allows the
float to move freely “up/down” according to related water levels. As water levels
rise, so does the float causing the water inlet valve to close at a pre-determined
level. As water levels fall, so does the float causing the water inlet valve to open
allowing replenishment of water.
“B” is the “secondary” flotation device that engages “only” in the event of a
malfunction of flotation device “A” to prevent possible overflow conditions. The
design parameter of this device only allows the float to move “upward” as water
levels rise, causing the water inlet valve to close permanently. When flotation
device“B”engages,amanual“re-set”oftheoatationdeviceisrequiredinordertorestorenormal(incoming)water
activity.
1. Disconnect (unplug) the power cord.
2. Turn off the water supply, using manual shut-off valve at the rear of the dispenser.
3. Placecup/glassunderdispensingspigotanddrainapprox.3cupsofcoldwater.
4. Removethetopcoveronthedispenser(SeeFig.17)byremovingthetwoPhilipsscrewslocatedattherearofthe
cover(SeeFig.17A).
5. Carefully lift off the top cover.
6. Place a towel on top of the reservoir cover.
7. Pushthewhitere-setbuttonlocatedontopofthereservoircover(SeeFig.21).
A small burst of water will release from the re-set button depressurizing
the water line. This action will cause flotation device “B” to release. The
re-set procedure is now complete. Clean-up any access water on the
reservoir cover. Re-connect the power cord.
8. Slowlyre-openthemanualshut-offvalve(attherearofthedispenser).You
should hear water entering the reservoir. If not, close the manual shut-off
valveandrepeatsteps1,2,3,6,7,8.
9. Re-install the dispenser top cover and secure using the two Philips screws.
10. Re-connect the power cord.
Fig. 20
Fig. 21
LH
Condenser
coils
A
B
OVERFLOW RE-SET
Cleaning the Outside of the Water Dispenser:
Internal Reservoir Water Overflow Protection:
Re-Setting Water Overflow Protection:
Cleaning the Condenser:
IMPORTANT! Unplug the dispenser before performing this procedure. Dispense hot water until temperature
drops to a safe level to avoid the risk of scalding.
1. Turn off the water supply, using manual shut-off valve at the rear of the dispenser.
2. Press both dispensing buttons until water stops flowing.
3. Placeacontainer/bucketbeneaththedrainvalvelocatedattherearofthedispenser(SeeFig.18).
4. Removethedraincapandplugfromthedrainvalveandlettheremainingwaterowintothecontainer/bucket.
Replace the cap and plug.
When not using the dispenser for long periods of time or when going on vacation, unplug the dispenser and drain the
reservoirs (see Draining the Reservoirs). Follow Initial Product Cleaning Procedures upon return and startup of the
dispenser.
Attention:Donotreturnthisproducttothestore.Forquestionsonoperation,assemblyorparts,pleasecontactusat
www.greenwaywt.comor1-866-253-0447.
PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION
Water dispenser is leaking. Check all water line connections for
leaks.
Filter not properly secured and locked.
Drain cap and plug are not secure.
Coldtankreservoirisoverlled.
Repair water line connections and make sure
blue locking “c-clips” are installed on water
lines.
SecureFilterandlock.
Ensure drain plug is secure and tighten drain
cap.
SeeRE-SETTINGWATEROVERFLOW
PROTECTION
GWD9500W-POU / GWD9500BLS-POU
Heating Temp (approx.): 194°F / 90°C
Cooling Temp (approx.): 35 - 52°F / 2°C - 11°C
Hot Cold
Output per hr: 1.2 gal / 4.6 L 0.5 gal / 2.0 L
Internal Tank: 0.2 gal / 0.6 L 0.8 gal / 3.6 L
Power Consumption: 1150 W 88 W
Working Water Pressure: Up to 120psi
10
Draining the Reservoirs:
Going Away on Vacation:
specIfIcatIons:
tr o u b l e s H o o t I n G tI p s :
No hot water. Insufcientwaterlevelsinthereservoir.
The unit is unplugged.
Kettle Feature button was not activated.
Temperature limit switch tripped.
Makesureallwatershut-offvalvesareopen.
Plug in the power cord.
Activate the Kettle Feature button.
The temperature limit switch will re-set
automatically when the temperature of the
water drops.
No cold water. The circuit breaker in your home is
tripped or the fuse is blown.
The unit is unplugged.
Thermostat needs to be adjusted colder.
Reset the breaker or replace the fuse.
Plug in the power cord.
Adjust thermostat between L (warm) and H
(colder) levels to achieve desired temperature.
Water dispenser is not
dispensing water.
Water shut-off valves are closed. Open all water shut-off valves.
Alarm is beeping
continuously.
Water leakage detection system is
activated.
RefertoWaterLeakageDetectionSystem
instructions in the manual.
11
Retailer: ModelNumber:
SerialNumber: DateCode:
Purchase Date:
Warranty DO NOT RETURN THIS PRODUCT TO THE STORE:
Greenway Water Technologies warrants your water dispenser to be free from manufacturer’s defects in workmanship or material under
normal operating conditions for one (1) year from the original date of purchase. This warranty applies only in the country in which it is
sold, and is available to the original purchaser only. This warranty is non-transferable.
ThiswarrantyandtheCSAInternationallistingforthiswaterdispenserarevoidifthewaterdispenserisaltered,modified,orcombined
with any other machine or device. Alteration of this water dispenser may cause serious flooding and/or hazardous electrical shock or fire.
The provisions of this warranty shall not apply to the following:
• Waterbottles.
• Servicetripstoyourhometoteachyouhowtousetheproduct.
• Improperinstallation,delivery,ormaintenance(failuretomaintaintheproductaccordingtotheinstructionsoutlinedintheproduct
manual will automatically void the warranty).
• Failureoftheproductifitisabused,misused,altered,usedcommercially,orusedforotherthantheintendedpurpose.
• Productsthatareusedoutsidearesidentialorofficeenvironment.
• Replacementofhousefusesorresettingofcircuitbreakers.
• Useofthisproductwherewaterismicrobiologicallyunsafeorofunknownquality.
• Damagetotheproductifusedtodispenseanythingotherthanwater.
• Damagetotheproductcausedbyaccident,fire,floods,oractsofGod.
• Anyservicetotheproductbyunauthorizedpersonnel.
• Incidentalorconsequentialdamagecausedbypossibledefectswiththisappliance,itsinstallationorrepair.
This warranty shall be fulfilled at an authorized Greenway Repair Facility. All warranty repairs must be pre-authorized by Greenway Water
Technologies. Greenway will, at its option, repair or replace free of charge any defective part, where the Purchaser has notified their
Retailer or Greenway Water Technologies within the warranty period. The obligation of Greenway Water Technologies under this warranty
is expressly limited to such repairs or replacement. This warranty does not cover the freight costs to and from the authorized repair
facility.
Exceptassetforthhereinorrequiredbylaw,theManufacturermakesnootherwarranty,guarantee,oragreement,express,implied,or
statutory including any implied warranty of merchantability or fitness for a particular purpose. The manufacturer does not assume or
authorize any person to assume any obligations of liability in connection with this water dispenser. In no event will the manufacturer be
liableforindirect,special,orconsequentialdamages(including,withoutlimitation,economicloss)orforanydelayintheperformanceof
this agreement due to causes beyond its control.
Somestatesorprovincesdonotallowlimitationsonhowlonganimpliedwarrantylasts,sotheabovelimitationmaynotapplytoyou.
Somestatesorprovincesdonotallowtheexclusionorlimitationofincidentalorconsequentialdamages,sotheabovelimitationor
exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state or from province to province.
Ifyourequireservice,pleasefirstseethe“Troubleshooting”sectionofthismanual.Additionalassistancecanbefoundbycheckingour
website at www.greenwaywt.com, or by calling our customer service line at 1-866-253-0447,MondaytoThursdayfrom8:30AMto5:00
PM(EST),Fridayfrom8:30AMto4:00PM(EST),orwrite:GreenwayWater Technologies,CustomerServiceCenter,400Southgate
Drive,Guelph,ON,CanadaN1G4P5.
Keep this manual and your sales slip together for future reference. You must provide proof of purchase for in-warranty service.
Write down the following information about your water cooler to better help you obtain assistance or service if your ever need it. You will
need to know your complete model number and serial number. You can find this information on the back of the water dispenser.
Water Technologies
Water Technologies
Water Technolo
g
ies
Mercid'avoirachetéundistributeurd'eauGreenway®.Lisezavecsoinlesconsignesd'utilisationquiaccompagnent
votreappareiletconservezcelivretpourvousyréférer.Nousavonsconçuavecsoinvotredistributeurd'eauGreenway®
pour vous donner plusieurs années de service plaisant et de fonctionnement sans panne.
REMARQUE IMPORTANTE :Ledistributeurd'eauGreenway®a été conçu avec une fonction de sécurité spéciale
(interrupteuràotteur)destinéeàcontrôlerl'activation/lefonctionnementdusystèmedechauffageduréservoird'eau
chaude(fonctionbouilloire).Encasd'absenced'eauet/ousilesniveauxd'eausontbasdanslecircuitduréservoir
interne,ilestimpossibledemettreenmarche/fairefonctionnerlesystèmedechauffaged'eau.Silechauffaged'eau
chaudeenmarcheetquedel'eauestsoutiréesimultanémententraînantlachutedesniveauxd'eauendessousdes
niveauxdesécurité,l'opérationduréservoird'eauchaudeestautomatiquementarrêtéejusqu'àcequelesniveauxd'eau
normauxsoientrestaurés.Unefoislesniveauxrestaurés,vousdevezréactivermanuellementlesystèmedechauffage
d'eauchaudeenappuyantsurleboutonrouge(fonctionbouilloire).REMARQUE:Lesystèmed'eaufroiden'estpas
affecté par cette fonction de sécurité.
CONSIGNES DE SÉCURITÉ IMPORTANTES
• Cedistributeuraétéconçupourêtreutiliséàl'intérieuruniquement.NEPASL'UTILISERL'EXTÉRIEUR.
• Nejamaisretournerledistributeuroul'inclinerdeplusde45degrés.Pendantletransport,siledistributeuraété
transportésurlecôté,leplacerverticalementpendant12heuresavantdelebrancheràlasourced'alimentationet
de le mettre en marche.
• Cedistributeurd'eauestéquipéd'uncordond'alimentationetd'unechemisàlamassepourdesraisonsde
sécurité.
• Ledistributeurd'eaudoittoujoursêtredansunendroitsec,loindetoutesourcedechaleuretdelalumièredujour.
• Nejamaisplacerdesmastèresinammablesprèsdudistributeur.
• Maintenirunintervalleminimumde5cmàl'arrièreetsurlescôtésdudistributeurpourgarantirunebonne
ventilation.
• Toujoursinstallerledistributeurd'eausurunsolplat(solide).
• Aprèsavoirarrêtéledistributeur,attendre3minutesavantdeleremettreenmarche.
• Toujoursdébrancher(déconnecter)lecordond'alimentationdudistributeurd'eauavantdeprocéderàdes
opérationsdemaintenance/réparation,aunettoyageetauremplacementdultre.
• Touteopérationdemaintenance/réparationdoitêtreeffectuéeuniquementparunpersonnelqualié/autorisé.
VeuillezcontacterleServiceàlaclientèleau+1-866-253-0447pourdeplusamplesinformationssurlesopérations
de maintenance/réparation.
• Selonlestermesdelagarantie,ledistributeurd'eaudoitêtrenettoyérégulièrement.
• Respecterlesinstructionsdenettoyageetdemaintenancestipuléesdanscemanuel.Lenettoyagedoitêtre
effectuétousles4à6mois.
• Ilvousincombedegarantir(vérier)quelesraccordementsdelaconduited'eausontcorrectsetétanchesetqu'il
n'yapasdefuitesdanslesystèmeavantdemettrel'unitéenmarche.
• Bienquecetteunitédisposed'uncommutateurdeprotectionàl'épreuvedesenfants(eauchaude),nejamais
laisserlesenfantsseservirdel'eauchaudesanssupervisiondirecteetappropriée.
DANGER:L'eauchaudedudistributeurestchaufféeàenviron90°C.Lestempératuressupérieuresà52°C
peuvententraînerdesbrûluresgraves.
• Lorsduremplacementdesltresdecetteunité,utiliseruniquementdesltresd'origine(OEM)Greenway®(VSRF-9).
INSTRUCTIONS DE MISE À LA TERRE
• Uneutilisationinadéquatedelachedemiseàlaterrepeutentraînerdes
chocsélectriques,pouvantainsicauserdesblessuresgraves,voirelamort.
• Cetappareildoitêtremisàlaterre.Encasdecourt-circuit,lamiseàlaterreréduitlesrisquesdechocsélectriquesen
procurantunchemind'évacuationducourant.
• Cetappareilestdotéd'uncordond'alimentationmunid'unconducteurdemiseàlaterreetd'unechemiseàlaterre,et
doitêtreraccordéàuneprisepolariséecorrectementmiseàlaterre.Faitesappelàunélectricienqualiésivousne
comprenez pas parfaitement les instructions de mise à la terre ou si vous avez des doutes sur la mise à la terre
adéquatedevotreappareil.Silaprisedecourantmuraleestuneprisestandardàdeuxbroches,ilvousincombedela
remplacerparunepriseàtroisbrochesmiseàlaterredefaçonadéquate.
• Necoupezetneretirezjamaislabrochedemiseàlaterreducordond'alimentation.
• N'utilisezpasunadaptateurdebranchementaveccetappareil.
• N'utilisezaucunerallongeaveccetappareil.Silecordond'alimentationesttropcourt,demandezàunélectricienqualié
d'installeruneprisedecourantàproximitédel'appareil.
VOTRE DISTRIBUTEUR D’EAU GREENWAY®
1. Couvercle supérieur
2. VoyantsdeSignalisationPrêt-À-Distribuer:
Jaune: "Clignotant: Faibleniveaud'eaudansleréservoirinterne.Lechauffe-eaunepeutpasêtreactivé
(vous devez remplir le réservoir).
"Éteint": Leniveaud'eauduréservoirinterneestinsufsantpouractiverlechauffe-eau
Bleu: “Allumé“:L’eaufroideaattentlatempératureoptimaleetestprêtepourladistribution.
“Éteint”: Lecyclederefroidissementestenmarche,ilestpossiblepourdistribuerl’eau
pendant le cycle de refroidissement, cependant, la température de
refroidissementoptimalenepeutencoreêtreréalisée
3. Boutondesécuritérésistanted'enfant
4. Bouton-poussoirpourl'eauchaude(distribue
aussidel'eauàtempératureambiantelorsque
lafonction“Kettle”n'estpasactivée)
5. Bouton-poussoir pour l’eau froide
6. Boutond’activation“Kettle”MARCHE/ARRÊT
“clignotant”: Le réchauffeur (réservoir d’eau
chaude) est en marche
“Allumé “ : L’eau chaude a atteint la température
optimaleetestprêtepourla
distribution.
"Éteint" Chauffage(réservoird'eauchaude)
désactivé;toutefois,l'eaudansle
réservoirpeutêtrechaude,ilfaut
ainsi user de prudence lors de la
distribution ou de la vidange du
réservoird'eauchaude.
7. Bac démontable
8. Thermostat réglable pour l’eau FROIDE
(à l’arrière du distributeur)
9. Vanne de vidange (à l’arrière du distributeur)
10. Serpentinducondensateur(àl’arrièredu
distributeur)
11. Panneauavantinférieur(ltresituéderrière)
12. Robinetd'arrêtmanuel(entréed'eau)
1
LH
3
11
7
62
5
10
8
12
9
4
1
Il est fortement recommandé de confier l'installation du distributeur d'eau à un plombier qualifié. Si vous vous
chargez de l'installation du distributeur d'eau, veuillez respecter les informations suivantes :
Enfonctiondelaplomberiedevotredomicile(tuyauxencuivreouexibles),lesaccessoiresdeplomberiesuivants(qui
nesontpasinclusavecledistributeurd'eau)sontnécessairesàl'installationcomplètedevotredistributeurd'eau.Vous
pouvezvousprocurercespiècesdansdesquincaillerieslocales.
• Téencuivrede½po(A)
• Extrémitéàsoudermâlede½poxrobinetd'arrêtavecraccordàcompressionD.E.de¼po(B)
• Aprèsl'installation(C)
• Fluxdebrasage
• Brasure
• Toiled'émeri
• Coupe-tube/tuyau
• Torchedesoudage
• Serviettes(pourépongerl'eau)
• TéQuick-Grip½x½x½po(D)
• Quick-Grip½poxrobinetd'arrêtavecraccordàcompressionD.E.de¼po(E)
• Aprèsl'installation(F)
2
(A) (B) (C)
(D) (E) (F)
InstructIons d'InstallatIon:
TUYAUX EN CUIVRE (BRASAGE REQUIS):
TUYAUX FLEXIBLES (PAS DE BRASAGE NI DE COLLE REQUIS) :
OUTILLAGE REQUIS:
• Coupe-tube/tuyauenplastique
Sélectionnezunemplacementappropriéàl'installationdudistributeurd'eau(dansvotremaison/cuisine)avecaccèssimple
àuneprisemuraleélectriqueetuneconduited'eaufroide.
1. IMPORTANT:Coupezl'alimentationeneaufroide.
2. Ouvrezlerobinetd'eaufroidepourpurgerlesystème(anderéduirelenettoyageaprèsunefuited'eau).
3. Envousservantd'uncoupetube/tuyau,coupezàlahauteursouhaitéeetretirezlasectiondelaconduited'eau
froidedécoupée(lacoupedoitsesituerau-dessusdurobinetd'arrêtmanuelinstallésurlaconduited'eau).
4. TUYAUX EN CUIVRE :Envousservantdelatoiled'émeri,nettoyezlesdeuxextrémitésdestuyauxencuivreet
appliquezleuxsurtouteslessurfacesàbraser,ycomprisl'intérieurduté.Suivezlesinstructionsd'installationdu
fabricantlivréesavecl'extrémitéàsoudermâlede½poxrobinetd'arrêtavecraccordàcompressionD.E.de¼po(B)
5. TUYAUX FLEXIBLES :Suivezlesinstructionsd'installationdufabricantlivréesavecletéQuick-Grip½x½x½po
(D)etleQuick-Grip½poxl'extrémitéàsoudermâlede½poxrobinetd'arrêtavecraccordàcompressionD.E.
de¼po(E)
6. Fermezlerobinetd'arrêtquevousvenezd'installer(voirlaFig.1AetlaFig.1B)etlentementouvrezànouveau
laconduited'alimentationeneaufroide.Vériezlaprésencedefuitespotentielles.Sivousdétectezdesfuites,fermez
immédiatementl'alimentationeneauetréparezlesfuites.Sivousnedétectezaucunefuite,passezàl'étape7.
7. Ledistributeurd'eauestdotéd'uneconduited'eauexiblede8mavecunD.Ede¼po.Sivousavezbesoinde
longueurssupplémentairesdeconduite,vouspouvezvouslesprocurerdansdesquincaillerieslocales.Coupezàla
longueursouhaitéepoursatisfairelesconditionsdel'installationenvousassurantquelacoupedesdeuxextrémités
delaconduited'eauestbiendroite.(VoirlesFig.1etFig.2)Retirezl'écrouetlabaguedecompressiondurobinetet
installezsurlaconduited'eau.(VoirFig.3)
3
Fig. 1A (Robinet ouvert) Fig. 1B (Robinet fermé)
Fig. 1 (Correct) Fig. 2 (Incorrect) Fig. 3
OUTILLAGE REQUIS:
EMPLACEMENT DE L'INSTALLATION:
dé b u t d e s op é r a t I o n (ra c c o r d e M e n t d e la co n d u I t e d'e a u prIncIpale):
Introduisezlaconduited'eaudanslerobinetaussiloinquepossible(voirlaFig.4),faitesglisserl'écrouetlabaguede
compressionendirectiondurobinetetresserrezensuitefermementl'écrouàl'aided'uneclé.ATTENTION : NE PAS
SERRER AVEC EXCÈS. (Voir la Fig. 5)
8. Ledistributeurd'eauestmunid'unrobinetd'arrêtmanuelinstalléàl'arrièredel'unité(voirlaFig.6A)auquelvous
pouvezaccéderfacilementencasd'urgence.Notez:L'orientation(positiondemontage)pourlerobinetd'arrêtpeut
varierenfonctiondevotremodèle(ex:horizontauxouverticaux),maislaprocédured'installationdel'eauenligne
pourlesdeuxversionsestlemême.(Voirl'étapen°9).
9. Raccordezlaconduited'eauàl'arrivéeaucôtéouvertdurobinetd'arrêtmanuel(voirlaFig.6B).Pourcerobinet,
utilisezdesraccordsdeconduited'eaudetypebranchementrapide(aucunoutillagerequis).Ilsuftd'insérer
(pousser)l'extrémitédelaconduited'eauleplusloinpossibledanslerobinetd'arrêt.
AVERTISSEMENT : NE PAS OUVRIR LA CONDUITE D'ALIMENTATION EN EAU À CE NIVEAU.
(voir l'installation du filtre)
10. Pourdéconnecter(retirer)laconduited'eaudurobinetd'arrêt,vousdevezd'abordenleverleclipencdeblocage
bleu(voirlaFig.4)entirantdessusversl'avant.
11. Pourdégagerlaconduited'eau,appuyez,enmaintenantvotrepression,surlecollierexterne(blanc)autourde
laconduite(voirlaFig.15)ettirezenmêmetempspourdégagerlaconduited'eau.REMARQUE:Lesclipsencde
blocagedoiventtoujoursêtreinstallésavantlesconduitesd'eau.
Pourdesquestionsd'hygiène,leltreinclusaudistributeurd'eaun'apasétéinstalléàl'usine.Ilaétéexpédiédansson
emballagethermorétractabled'origine(scellé).Leltreestsituéderrièrelepanneauavantinférieurdudistributeur.Pour
accéderaultre:
• Enlevezlebacd'égouttageenletirantversl'avant(voirlaFig.7).
• RetirezlavisPhilipsxantlepanneauinférieur(voirlaFig.8).
• Leltreesttenupar2clips.Retire,etdéballeleltre(voirlaFig.9&9A).
4
Fig. 4 Fig. 5 Fig. 6
A
B
Fig. 7 Fig. 8
Fig. 9 Fig. 9A
InstallatIon d u fI lt r e :
• Pourxerleltreàlatêtedultre,assurez-vousquelalanguettedeblocagebleuesituéeàl'avantdelatêtedu
ltresoitrepousséetoutenhaut(voirlaFig.10).
• Vissezleltre(1/4detourdanslesenshoraire)danslatêtedultrejusqu'aublocage.Appuyezsurlalanguettede
blocagebleuepourlaplacerenpositionverrouillée(voirlaFig.11).Silalanguettedeblocagenerevientpasdans
cettepositionverrouillée,celasigniequeleltren'estpassufsammentserré(resserrez).
• Laècherougesituéesurlatêtedultreindiquelesensdedébitdel'eau(arrivée/sortie)parleltre.
• L’installationestmaintenantterminée.Commedanstouslescasd'installationdeplomberie,l'alimentationen
eaudoitêtreouvertelentementetlesraccordementsdoiventêtreinspectésandedétecterlaprésencedefuites
avantd'ouvrirtotalementlesrobinetsd'eau.Sivousdétectezdesfuites,fermezimmédiatementl'alimentationen
eau et réparez les fuites.
• Pourdéconnecter(retirer)lesconduitesd'eaudelatêtedultre,vousdevezd'abordenleverleclipencdeblocage
(bleu)(voirlaFig.4)entirantdessusversl'avant.
• Pourdégagerlaconduited'eaudelatêtedultre,appuyez,enmaintenantvotrepression,surlecollierexterne
(blanc)autourdelaconduite(voirlaFig.15)ettirezenmêmetempspourdégagerlaconduited'eau.REMARQUE:
Cesclipsencdeblocagedoiventtoujoursêtreinstallésavantlesconduitesd'eau.
5
Fig. 10 Fig. 11
UNLOCK LOCKE
Fig. 13 Fig. 14 Fig. 15
This manual suits for next models
1
Table of contents
Languages:
Other Greenway Home Products Water Dispenser manuals
Greenway Home Products
Greenway Home Products VWD8956W User manual
Greenway Home Products
Greenway Home Products GWD4650W User manual
Greenway Home Products
Greenway Home Products GWD1000BLS User manual
Greenway Home Products
Greenway Home Products GWD6960BLS User manual
Greenway Home Products
Greenway Home Products GWD860W-3 User manual
Greenway Home Products
Greenway Home Products vitapur VWD866W-3 User manual
Greenway Home Products
Greenway Home Products GWD5440W User manual
Greenway Home Products
Greenway Home Products GWD5570WBC User manual
Greenway Home Products
Greenway Home Products Polar PWD8975W User manual
Greenway Home Products
Greenway Home Products GWD2630W-1 User manual
Greenway Home Products
Greenway Home Products GWD860W-3 User manual
Greenway Home Products
Greenway Home Products Polar PWD5975BLS User manual
Greenway Home Products
Greenway Home Products GWD220W-2 User manual
Greenway Home Products
Greenway Home Products GWD5960W User manual
Greenway Home Products
Greenway Home Products GWD5400W User manual
Greenway Home Products
Greenway Home Products GACS835 Service manual
Greenway Home Products
Greenway Home Products GWF8L User manual
Greenway Home Products
Greenway Home Products GWD5500WBC User manual
Popular Water Dispenser manuals by other brands
Strauss water
Strauss water T6 Customer guide
IBC Water
IBC Water AST0715-940 Installation & operating instructions
WaterLogic
WaterLogic P2 Classe manual
Haier
Haier WDNS116BBS user manual
Excalibur Water Systems
Excalibur Water Systems Superior Series installation manual
Excalibur Water Systems
Excalibur Water Systems CHLOROSOFT SERIES installation manual