Grillo CLIMBER 8.22 User manual

02424-15
CLIMBER 8.22
OPERATOR'S MANUAL
MANUALE DELL'OPERATORE
MANUEL D'UTILISATION
BEDIENUNGSANLEITUNG
MANUAL DE INSTRUCCIONES

SUMMARY
Safety rules 1
Informations and warnings 4
Instructions : 5
Warnings 5
Identification and servicing 6
Technical specifications 7
Instructions for use
Maintenance and lubrication 10
Pictures 4
EC Declaration of Conformity 53
INDICE
Norme antinfortunistiche 1
Etichette e avvertenze 4
Istruzioni : 15
Avvertenze 15
Identificazione e assistenza 17
Caratteristiche tecniche 17
Istruzioni d’uso 1
Manutenzione e lubrificazione 20
Figure 4
Certificato di Conformità CE 53
INDEX
Règles de sécurité 1
Étiquettes et mise en garde 4
Instructions : 26
Mises en garde 26
Identification et assistance 2
Caractéristiques techniques 2
Mode d’emploi 29
Maintenance et lubrification 31
Illustrations 4
Certificat de Conformité CE 53
INHALTSÜBERSICHT
Sicherheitsvorschriften 1
Etiketten und Warnungen 4
Anleitung: 37
Sicherheitsrelevante Hinweise 37
Identifikation der Maschine und Kundendienst 39
Technische Daten 39
Inbetriebnahme der Maschine 40
Wartung und Schmierung 42
Abbildungsverzeichnis 4
EG-Konformitätserklärung 53
-
i
-

SAFETY SYMBOLS - SIMBOLOGIA PER LA SICUREZZA - SYMBOLOGIE POUR LA SECURITE – SICHERHEITSSYMBOLE-
SIMBOLOGÍA DE SEGURIDAD
OPEN MANUAL- means that ou must read the operator's manual ver carefull .
MANUALE APERTO - significa che dovete leggere attentamente il manuale di uso e manutenzione.
MANUEL OUVERT – signifie qu'il faut lire avec attention le présent manuel.
OFFENES HANDBUCH – bedeutet, dass Sie die Gebrauchs- und Wartungsanleitung aufmerksam durchlesen müssen.
MANUAL ABIERTO – es decir que ha que leer mu atentamente el manual del operador.
CAUTION! - means that ou have to pa particular attention to the operation ou have to carr out, in particular if there is the
indication “DANGER”.
ATTENZIONE! - significa che dovete porre particolare attenzione all’operazione che dovete effettuare, in particolare se vi è anche
l’indicazione di “Pericolo”.
ATTENTION! - signifie qu'il faut faire particulière attention dans l'opération que vous allez faire, en particulier s'il a aussi
l'indication “DANGER”.
VORSICHT! - bedeutet, dass Sie besondere Aufmerksamkeit beim Durchführen des Vorgangs haben müssen, insbesondere wenn
auch der Hinweis “GEFAHR” aufgeführt ist.
ATENCIÓN! - es decir que ha que poner ma or atención en la operación a ejecutar si, en particular cuando ha también la
indicación “Peligro”.
INTERDICTION, YOU MUST NOT DO THAT! - means that it is absolutel forbidden to carr out the operations reported under this
s mbol because the could lead to mortal danger.
DIVIETO, NON FARE! - significa che non dovete assolutamente fare le operazioni riportate sotto questo simbolo, potrebbe
comportare un pericolo mortale.
INTERDICTION, NE PAS FAIRE! - signifie qu'il est absolument interdit d' effectuer les opérations reportées sous cette indication,
car elles pourraient conduire au danger de mort.
VERBOT, strengstens untersagt! - bedeutet, dass der Vorgang unter diesem S mbol absolut nicht durchgeführt werden darf, da er
zur einer lebensgefährlichen Situation führen könnte.
PROHIBICIÓN, NO LO HAGAN! - es decir que no ha que hacer absolutamente las operaciones bajo este símbolo, podría
comportar un peligro mortal.
NOTE, ou have to pa particular attention to the note put next to this s mbol
NOTA, dovete porre particolare attenzione alla nota posta accanto a questo simbolo.
NOTE, il faut faire attention particulière à la note mise à côté de ce s mbole.
ANMERKUNG, besondere Aufmerksamkeit muss auf die Anmerkungen neben diesem S mbol gelenkt werden.
NOTA, ha que poner atención particular en la nota puesta a lado de este símbolo.
You must not repair nor lubricate the machine with moving parts or with the engine put on.
Non riparare o lubrificare la macchina con organi in movimento o motore acceso
Ne pas réparer ou lubrifier la machine avec des parties en mouvement ou à moteur en marche.
Niemals bei bewegenden Objekten oder bei laufendem Motor Reparationen oder Einschmierungen durchführen.
No reparar ni lubrificar la máquina con órganos en movimiento o motor en marcha.
You must not smoke, light matches or lift flames, trigger frames nor cause sparks.
Vietato fumare, accendere fiammiferi o fiamme, lasciare fiamme libere o creare scintille.
Il est interdit de fumer, allumer des allumettes ou du feu, laisser des flammes libres ou de causer des étincelles.
Es ist untersagt zu Rauchen, Streichhölzer oder Feuer anzuzünden, Flammen auslösen oder Funken verursachen.
Prohibido fumar, encender cerillas o fuego, dejar llamas o crear chispas.
Use personal protective equipment.
Utilizzare mezzi di protezione individuali.
Utilisez l'équipement de protection individuelle.
Individuelle Schutzausrüstung benutzen.
Utilizar dispositivos de protección individual.

Take special care not to touch hot parts of the engine.
Prestate particolare attenzione a non entrare in contatto con parti surriscaldate del motore.
Veiller tout particulièrement à ne pas toucher des éléments surchauffés du moteur.
Achtung – keine heißen Motorteile berühren!
No tocar partes recalentadas del motor.
Tome muito cuidado para não entrar em contacto com as partes aquecidas do motor
Engine exhaust fumes can cause sickness or death. If it is necessary to run an engine in an
enclosed area use an exhaust pipe extension to remove the fumes. Always try to work in a
well ventilated area.
I gas di scarico possono causare malanni o morte. e è necessario mettere in moto un
motore in uno spazio chiuso, usare una prolunga tubo di scarico per far uscire il fumo.
Lavorare in una zona ben ventilata.
L’exhalation des gaz d’échappement peut être cause d’intoxication ou de mort. S’il est
vraiment nécessaire d’allumer le moteur à l’intérieur appliquer au tuyau d’échappement un
autre tuyau extensible pour permettre la sortie des gaz. Il est toujours mieux de travailler en
plein air.
Auspuffgase können Übelkeit oder Tod verursachen. Wenn es notwendig ist, einen Motor in
einem geschlossenen Raum laufen zu lassen, benützen ie eine Verlängerung, um das
Auspuffgas abzuleiten. Versuchen ie immer in einem gut belüfteten Raum zu arbeiten.
Los gases de escape pueden provocar enfermedades o muerte. De tener que poner en
marcha un motor en un espacio cerrado usar una prolongación del tubo de escape para que
salga el humo. Trabajar en una zona bien ventilada.
Os gases de escape podem causar danos ou morte. Caso seja necessário fazer com que o
motor funcione num espaço fechado, utilize uma extensão para o tubo de escape que os
fumos sejam expulso para o exterior. Trabalhe numa área bem ventilada.
Caution! Never touch moving pulleys or belts. They can be very dangerous. Never do
maintenance with engine running.
Attenzione! Non toccare mai pulegge o cinghie in movimento, creano gravi danni alla
persona. Non fare manutenzione col motore in moto.
Attention! Ne jamais toucher ni poulies ni courroies en mouvement elles peuvent provoquer
des accidents aux personnes. Ne pas faire l’entretien quand le moteur est en marche.
Vorsicht! Nie laufende Riemenscheiben oder Treibriemen anfassen, da es gefährlich ist. Nie
bei laufendem Motor Instandhaltung machen.
¡Atención! No tocar jamás poleas o correas en movimiento porque pueden crear graves
daños a la persona. No efectuar el mantenimiento con el motor en marcha.
Atenção! Nunca toque nas polias ou correias em movimento devido ao alto risco de
ferimentos. Nunca faça a manutenção da máquina com o motor ligado.
A burst which separates the tyre from the rim parts can cause serious injury or death.
La separazione fra pneumatico e cerchione, causata dall’esplosione del pneumatico, può
provocare serie ferite o addirittura la morte.
La séparation entre le pneu et la jante provoquée par l’explosion d’une roue peut causer des
dommages blessures ou la mort.
Die Trennung der Räder von den Felgen durch Explosion kann schwere Verletzungen oder
den Tod verursachen.
La separación entre el neumático y la llanta producida por la explosión del neumático puede
provocar graves herida e incluso la muerte.
A separação entre o pneumático e o aro, provocada pela explosão do pneumático, pode
causar graves ferimentos ou até mesmo a morte.

Prevent battery explosions: keep sparks lighted matches and open flames away from the top
of the battery. Battery gas can explode.
Per prevenire l’esplosione della batteria, tenete scintille, fiammiferi accesi e fiamme lontani
dalla stessa. Il gas della batteria può esplodere.
Prévenir l’explosion de la batterie: tenir les étincelles les allumettes et le feu loin de la
batterie. Le gaz de la batterie peut exploser.
Vorbeugung der Batterie-Explosion. Entfernen ie Funken, Zündhölzer und Flammen von
der Batterie. Das Batteriegas kann explodieren.
Para prevenir la explosión de la batería mantener chispas cerillas encendidas y llamas lejos
de la misma. El gas de la batería puede explotar.
Para prevenir explosão da bateria ter centelhas, fósforos acendido e chamas longe da
mesma. O gás da bateria poderia explodir.
Handle fuel with care it is highly flammable: Do not refuel machine while smoking when
machine is near an open flame or sparks or when the engine is running. Stop the engine.
Maneggiare il carburante con cura, è altamente infiammabile; non fate rifornimento mentre
fumate, o vicino a fiamme o scintille, o quando il motore è acceso.
Manier avec soin le carburant car c’est très inflammable. Ne pas remplir le réservoir si vous
êtes en train de fumer ou pendant que la machine est près du feu ou d’étincelles ou encore
pendant que la machine travaille. Arrêter le moteur.
Treibstoff vorsichtig handhaben, da er sehr entzündbar ist: beim Tanken nicht rauchen.
Nicht tanken, wenn die Maschine in der Nähe von Flammen oder Funken ist oder wenn der
Motor läuft. Immer den Motor abschalten.
Manejar el combustible con cuidado porque es sumamente inflamable; no repostar mientras
se fuma o cerca de llamas o chispas o cuando el motor está encendido.
Manuseie o carburante com cuidado, pois este è altamente inflamável; não fume durante o
abastecimento da máquina ou enquanto o motor estiver ligado, não o aproximado de chama
ou de faíscas.
Rotating blades are dangerous. Protect children and prevent accidents.
Le lame in movimento sono pericolose. Proteggete i bambini e prevenite gli incidenti.
Les lames en rotation sont dangereuses. Protéger les enfants et prévenir les accidents.
Arbeitende Messer sind gefährlich, Kinder schützen und Unfälle vorbeugen.
Las cuchillas en movimiento son peligrosas proteger a los niños y prevenir los accidentes.
As facas em movimento são perigosas. Proteger as crianças e prevenir acidentes.
Sulphuric acid in battery electrolyte is poisonous. It is strong enough to burn skin eat holes
in clothing and cause blindness if it gets in contact with the eyes.
L’acido solforico della batteria è velenoso. È in grado di causare bruciature alla pelle, bucare
vestiti e causare cecità se arriva negli occhi.
L’acide sulfurique de la batterie est toxique. Il peut causer des brûlures à la peau
endommager les vêtements et peut aussi causer cécité.
äure der Batterie ist giftig. ie kann die Haut verbrennen, Löcher in die Kleidung machen
und Blindheit verursachen.
El ácido sulfúreo de la batería es venenoso puede provocar quemaduras en la piel agujar la
ropa y provocar ceguera si llega a los ojos.
O acido sulfúrico e tóxico. Pode ser causa de queimadura da pele, furar roupa e provocar
cegueira, no caso chegarem em contacto com os olhos.
Avoid tipping. Do not drive where machine could slip or tip. Stay alert for holes and other
hidden objects.
Evitate le scivolate. Non guidate dove la macchina potrebbe scivolare o inclinarsi. Attenzione
a buche o ad oggetti nascosti.
Éviter les pentes. Ne pas conduire la machine où elle pourrait glisser ou se renverser. Faire
attention aux trous ou à tout autre obstacle caché.
Nicht dort fahren wo die Maschine rutschen könnte. Vorsicht bei Löchern oder versteckten
Gegenständen.
Evitar patinazos. No conducir donde la máquina pueda patinar o inclinarse. Cuidado con los
baches o con objetos escondidos.
Evitar deslizamentos. Não dirija em lugares onde a maquina poderia deslizar. Ter cuidado a
buracos e objetos escondidos.

DANGER! Machine roll-over: Do not use this machine on slopes greater than 17° (30%).
PERICOLO! Ribaltamento della macchina. Non usare questa macchina su pendii superiori ai
17° (30%).
DANGER! Renversement de la machine. Ne pas utiliser cette machine sur des pentes
supérieures à 17° (30%).
GEFAHR! Umstürzen der Maschine. Die Maschine nicht an Hängen mit einer Neigung über 17°
(30%) einsetzen.
¡PELIGRO! Volcado de la máquina. No utilizar esta máquina en pendientes superiores a 17°
(30%).
PERIGO! Revirado da máquina. Não use essa máquina em inclinações além de 17° (30%).
WARNING! SHARP PARTS. Keep hands and feet away. Do not operate the mower over
gravel or foreign bodies which may be sucked up and ejected by the blades generating a
danger. Keep people away. Remove the key and read the instruction manual before
attempting to carry out any maintenance or repairs to the machine.
ATTENZIONE! ORGANO TAGLIENTE. Tenere lontano mani e piedi. Non lavorare col
rasaerba sopra alla ghiaia o corpi estranei che possono essere aspirati e centrifugati dalle
lame risultando molto pericolosi, tenere lontano le persone. Togliere la chiave e leggere le
istruzioni prima di effettuare qualsiasi operazione di manutenzione e riparazione.
ATTENTION! ORGANE TRANCHANT. Éloigner les mains et les pieds. Ne pas utiliser la
tondeuse sur le gravier ou sur des corps qui peuvent être aspirés et centrifugés par les
lames et devenir très dangereux. Les personnes doivent se trouver à une certaine distance.
Enlever la clé et lire les instructions avant toute opération de maintenance et de réparation.
ACHTUNG! CHARFE KLINGEN. Hände und Füße fernhalten. Beim Mähen nicht über
chotter, teine oder andere Fremdkörper fahren, da diese durch die Drehbewegung der
Messer angesaugt und weggeschleudert werden können (Verletzungsgefahr). Nicht in der
Nähe von anderen Personen mähen. Vor jedem Wartungs- bzw. Reparatureingriff den
tartschlüssel abziehen und die Gebrauchsanleitung durchlesen.
¡PELIGRO! ÓRGANO CORTANTE. Mantener alejados los pies y las manos. No limpiar la
herramienta con el motor en marcha. ¡Peligro! Expulsión de objetos: mantener alejadas a las
personas. Atención: quitar la llave y leer las instrucciones antes de efectuar cualquier
operación de mantenimiento o reparación.
ATENÇÃO! Órgão cortante. Ficar longe com pés e mãos. Não trabalhar com a máquina
sobre cascalho ou objetos que podem ser aspirados e centrifugados gerando perigo,
manter-se longe das pessoas. Tirar a chave de ignição e ler as instruções antes de efetuar
qualquer operação de reparo ou serviço.

NOISE LEVEL
LIVELLO SONORO
NIVEAU SONORE
LAUTSTÄRKPEGEL
NIVEL DE RUIDO
4
CUTTING HEIGHT
ALTEZZA DI TAGLIO
HAUTEUR DE COUPE
SCHNITTHÖHE
ALTURA DE CORTE
DIFFERENTIAL LOCK
BLOCCAGGIO DIFFERENZIALE
BLOCAGE DIFFERENTIEL
DIFFERENTIALSPERRE
BLOQUEO DIFERENCIAL
GREASE PLAN
PUNTI DI LUBRIFICAZIONE
POINTS DE LUBRIFICATION
SCHIMIERPLAN
CAUTION, DANGER! PLEASE READ THE MANUAL
ATTENZIONE, PERICOLO! LEGGERE IL MANUALE
ATTENTION, DANGER! LIRE LE MANUEL
VORSICHT, GEFAHR! DIE ANLEITUNGEN LESEN
ATENCION, PELIGRO! LEER EL MANUAL
CAUTION, DANGER!
ATTENZIONE, PERICOLO!
ATTENTION, DANGER!
VORSICHT, GEFAHR!
ATENCION, PELIGRO!
FAST
RAPIDE
SCHNELL
RAPIDA
SLOW
LENTE
LANGSAM
LENTA
PARKING BRAKE
FRENO DI
STAZIONAMENTO
FREIN DE PARKING
FESTSTELLBREMSE
FRENO DE
ESTACIONAMIENTO
STARTER
MAX
MIN
SLOW
LENTE
LANGSAM
LENTA
FAST
RAPIDE
SCHNELL
RAPIDA

Climber 8.22/ Translation of the original instructions
HYDROSTATIC RIDE-ON BRUSH CUTTER
CLIMBER 8.22
Dear Customer,
thank you for choosing the Grillo CLIMBER. e hope that this new ride-on brush cutter mower will
perfectly meet your requirements. For best use and maintenance over time, please carefully read and
follow the instructions given in this manual. This will enable you to get top results from your mower
and will prevent avoidable expense. Please look after this manual which should always be kept with
the machine.
GENERAL DESCRIPTION AND INTENDED USE
The Grillo machine Climber 8.22 is a ride-on brush cutter designed for the cut of grass, on slopes
also.
WARNING! Be ore starting the engine, read this manual care ully. The
ollowing warnings are very important in ensuring sa ety!
WARNINGS
Caution is the best tool for accident prevention.
You are urged to read the following instructions for use of the mower before starting work.
Incorrect use of the mower and its equipment may cause damage. To reduce this risk, follow the
precautions given below:
1) Read the whole of this before turning on and using the brush cutter, before starting any work at
all.
2) Pay particular attention to the warnings and safety labels set out around the brush cutter.
3) Before allowing others to use the mower, inform them of the safety rules and carefully instruct
them on how to use the machine.
4) Before starting work, put on suitable working clothes, gloves, boots and protective glasses.
5) ear special acoustic protections (ear-caps) during work.
6) Before turning on the machine, make sure there are no persons around it; especially children.
7) Before driving the machine in reverse, make sure there are no persons or obstacle in the way.
8) Check the condition of the ground before mowing. Make sure that there are no stones, sticks, or
other objects, which could be run over and become a danger when projected.
9) If any impact with a foreign object occurs, disengage the blade, turn off the engine, remove the
ignition key and examine the brush cutter. If the machine vibrates, have it repaired.
10) Before getting off the brush cutter, turn off the engine, turn off the PTO, remove the ignition key
and lower the cutting deck in the lowest position.
11) Always drive slowly along uneven paths.
12) Keep the speed down when driving down slopes.
13) Always turn slowly when driving downhill.
14) The user is always liable for any damage caused to third parties.
15) Deformed or damaged blades must always be replaced, never just repaired.
16) Always use original GRILLO spare parts and accessories.
17) Only work in sunlight or under effective artificial lighting.
18) Only store fuel in suitable containers designed for the purpose.
19) Be very careful when working close to a road.
20) Allow the engine to cool before putting the machine away in a closed environment.
21) Do not operate the machine when tired or after drinking alcohol.
22) Do not allow any fuel spillage and after filling the tank wipe away any spilled fuel before starting
the engine.
23) Do not tamper with the safety devices or disable them.
24) Do not change the engine settings, especially the maximum r.p.m.
25) Do not rest heavy loads on the seat, the starter safety device could become disengaged.
26) Never attempt any adjustments or cleaning with the engine running.
5

Climber 8.22/ Translation of the original instructions
27) Never allow anyone to check the machine while you are seated at the controls with the engine
running.
IMPROPER USE TO BE AVOIDED
28) Do not allow passengers to ride on the machine.
29) Do not allow under-age children to operate it; use is prohibited to children under 16 years old.
30) Do not operate the brush cutter near to ditches or verges which could collapse under the weight
of the machine, especially when the surface is loose or wet.
31) Replace worn or damaged exhausts.
FURTHER SAFETY ADVICE
The above mentioned warnings could not be enough to avoid any risk, if the operator does not use
the present brush cutter correctly. Therefore, for your safety we give you following advices:
32) The blade is very dangerous when rotating, never put hands or feet underneath the mower deck.
33) Do not drive in reverse at high speed.
34) It is dangerous to operate the steering wheel abruptly with the engine at full power.
35) Fill the tank with fuel before starting the engine. Only refuel outdoors, always turn off the engine,
keep away from sparks or naked flames, do not smoke! Always replace the cap on the fuel tank
and those on fuel containers properly.
36) If the fuel tank has to be emptied, only do so outdoors.
37) Do not operate the brush cutter over gravel which could become sucked up and drawn into the
blade, becoming very dangerous.
38) If you have children, hide the ignition key after using the machine.
39) CAUTION: to avoid the risk of fire, keep the engine compartment, exhaust, discharge outlets,
battery, tank area and fuel pipes free from grass, leaves, dirt etc.
40) Do not store the machine inside any building where the engine fumes can reach naked flames,
sparks or bare electrical wires.
Remove the implements, turn off the engine and disconnect the spark plugs:
a) be ore cleaning obstructed points.
b) be ore checking or repairing the brush cutter.
c) when the machine hits a oreign body (check the mower deck to see i it is damaged and
make repairs be ore you operate).
d) i abnormal vibration occurs, stop and inspect the machine. Contact the nearest authorized
service centre i you need help.
IDENTIFICATION AND SERVICING
IDENTIFICATION
The brush cutter has a label on the steering
column indicating the machine’s serial number.
TECHNICAL ASSISTANCE
This manual provides instructions for use and basic maintenance of the brush cutter by the user. For
operations that are not described in this manual, contact the nearest authorized Grillo dealer.
SPARE PARTS
Only use original spare parts. These are the only parts that ensure safety and interchangeability.
Always quote the machine’s serial number and the code number of the part to be replaced when
ordering spare parts. For engine parts, follow the indications given in the specific manual.
6

Climber 8.22/ Translation of the original instructions
WARRANTY
The guarantee is given in compliance with the current law. The dealer will have to give the client a
copy of the registration card of the machine, which they will print up from the Grillo website. For the
engine the guarantee of the relative manufacturers apply.
RECOMMENDED LIST OF SPARE PARTS TO BE KEPT IN STORE
2 x mowing blades
2 x blade screws
2 x blade screw nuts
1 x set of belts
1 x engine air filter
1 x engine oil filter
1 x throttle cable
2 x wiring system fuses
TECHNICAL SPECIFICATIONS
ENGINE: BRIGGS & STRATTON 7220 PROFESSIONAL SERIES, OHV, 656cc, twin-cylinder petrol
engine with oil pump
STARTING SYSTEM: electric with battery 12V.
GEARBOX: hydrostatic transmission.
DIFFERENTIAL: locking device with pedal engagement.
CLUTCH: electromagnetic with PTO and blade brake
GROUND SPEED: continuously variable from 0 to 10 km/h and reverse speed from 0 to 6 km/h.
TYRES: ront 3,50-6 TRACTOR – rear 18×9.50-8 TRACTOR.
BRAKE: service brakes on the front wheels with pedal engagement; parking brake on the rear wheels
with lever engagement.
OPERATOR SEAT: sprung and adjustable, equipped with roll-bar
CUTTING DECK: rear/side discharge.
CUTTING SYSTEM: 1 rotating blade.
CUTTING WIDTH: 910 mm.
BLADE SPEED: 81 m/sec.
CUTTING HEIGHT: from 35 mm to 110 mm with 6 cutting positions and 1 for travelling.
HOURLY CUTTING CAPACITY: 7000 m2/h (indicative)
INTERNAL STEERING RADIUS: 50 cm.
FUEL TANK: 7 litres EMERGENCY SUPPLY: 1 litre
TOW BAR AND FRONT LIGHT ARE STANDARD FEATURES
ATTACHMENTS: 125 cm orientable snow blade, snow chains for rear wheels.
SIZES: Length: 1895 mm, idth: 990 mm, Height: 980 mm.
WEIGHT: 265 kg
7

Climber 8.22/ Translation of the original instructions
INSTRUCTIONS FOR USE
PUTTING THE MACHINE INTO SERVICE
1) Check that the machine has not been damaged during transport.
2) Check the oil levels of the engine and of hydrostatic transmission.
3) Check the tyre pressure:
1.2 BAR front wheels 3,50-6 TRACTOR
1.2 BAR rear wheels 18×9.50-8 TRACTOR
4) Check the battery voltage; it must be at least 12 Volts. Charge if necessary.
5) IMPORTANT!!! During assembly take care not to reverse the polarity of the battery.
6) Fix the steering wheel taking care to insert the key properly and to tight the screw correctly
(tightening torque 2 KgF.m [20 Nm]).
7) Fit the muffler, the rear bumper and the roll bar.
RUNNING IN – CAUTION!!
Change the engine oil and filter after the first 20 working hours. Check that there are no oil leaks or
slack screws, especially those which fix the blade and the steering.
BEFORE STARTING UP THE ENGINE
Before starting up the engine, always check that:
– the travel lever is in idle position (2,fig. 3);
– the engine oil level is correct (fig. 4);
– the engine cooling intake grids are clean (fig. 4);
– air filter is clean (fig. 8).
– the mowing deck is clean;
– the hydraulic motor fins are clean (fig. 5);
– the blades are sharp and firmly fastened in place;
– the screw in the centre of the blade hub is safety tightened (3, fig. 9)
– the oil in the hydraulic axle is at the correct level (fig. 5); the correct level is 12 mm underneath the
bottom of the tank (fig. 10);
Fill the fuel tank using a funnel with very fine filter.
Adjust the seat by using the lever (fig. 2, position A).
STARTING UP THE ENGINE
– Push the throttle half way in (5, fig. 3)
– If the engine is cold, use the choke (6, fig. 3). Turn the ignition key (1, fig. 1).
– Once the engine has started, turn off the choke and wait for a few minutes to allow the engine to
warm up.
IMPORTANT: hen travelling with the mower from one place to another, keep the cutting deck at the
maximum height setting.
SWITCHING ON THE HEADLAMP
To switch on the headlamp, put the ignition key in the second position (fig. 15, position A).
IMPORTANT
It is necessary to switch on the headlamp once the engine has started up to avoid battery discharge.
STARTING WORK
– Choose the desired cutting height by means of the lever (fig. 2, no.8). Suitably accelerate the
engine and engage the PTO lever using the switch on the dashboard (fig.1, no. 6). Gently operate
the forward travel lever (2, fig. 3) and start work. To stop, return the forward travel lever to the stop
position.
– The lever (2, fig. 3) is also used to reverse. hen it is moved back, the machine moves backwards;
always operate it gently.
8

Climber 8.22/ Translation of the original instructions
FRONT BRAKE
The front brake (4, fig. 1) must be used only as emergency brake when driving downhill in order to
avoid the machine sliding. If you use it together with the differential lock, the machine is steadier,
above all in slope conditions. In normal conditions, to slow down and brake you only need to use the
feed lever. To adjust the cables use the adjusters (fig. 24).
PARKING BRAKE
To engage the parking brake lift the loop up (fig. 3, no. 10) and hook the lever. To adjust the parking
brake use the register (fig. 5).
DIFFERENTIAL LOCK
The differential lock pedal is the one indicated in fig. 1 no. 5. Press the differential lock pedal in case
of driving-wheels skidding. It is advisable to use the lock also sloping down and in steep slant to keep
both the driving-wheels in adhesion. CAUTION: Do not use the differential lock when turning.
HOUR METER
The machine is equipped with the an hourmeter with three different functions:
1) It always shows the no. of hours worked, even when the key is not inserted.
2) It displays the no. of hours to the next engine oil change (OIL CHANGE IN...HS). The first oil
change must be carried out after the first 20 working hours than every 100 working hours. The
indicator “OIL CHANGE” flashes automatically when it is necessary to change the oil.
3) It displays the no. of hours to the next lubrication (LUBE IN...HS). Lubrication must be carried out
every 40 working hours. The indicator “LUBE” flashes automatically when lubrication must be carried
out.
By pushing the white button you can choose the function to be displayed on the hour meter.
USEFUL RULES FOR EFFICIENT USE
1) Never strain the engine: when fumes are emitted from the exhaust it means that it is being
strained. Slow down.
2) Do not leave the machine out in the rain.
3) Frequently sharpen the mower blades: the cut will be better and the engine will not be strained too
much.
4) Check the land before mowing to make sure that there are no stones, sticks or foreign bodies.
5) Keep the engine at peak rpm during mowing, adjust the speed according to the height of the grass.
6) Keep the grids above the engine and the cooling ins o the hydraulic motor ( ig. 4 – 5)
clean.
CUTTING POSITIONS
The cutting position is adjusted using the lever (fig. 2, no. 8). The deck can be set in 4 different cutting
positions from 35 to 110 mm and one travel position in which the blade disengages automatically. In
case of uneven ground, humps or dips, the deck should be kept in the highest cutting position to
prevent knocks by the blade. On the cutter deck (fig. 27) a baffle is fixed under right hand side of the
deck (fig. 25). You can insert it on the seat (fig. 26) and fix it with the relative lever. This baffle helps to
obtain a homogeneous distribution of the cut grass. It has to be used only at 12/15 mm grass height.
SLOPING GROUND
If possible, steep slopes must be mown in the up/down direction, paying attention when turning that
the wheels upstream do not strike obstacles (stones, branches, roots, etc.) which might cause the
machine to overturn, or lead to loss of control. Assess the conditions and pay attention if the ground
and grass are damp since the machine might slip. Downhill, set off at low speed and do not pass over
dry or cut grass since the wheels lose grip. Remember that if you engage the differential lock and
possibly the front emergency brake (4, fig. 1) the machine is steadier.
9

Climber 8.22/ Translation of the original instructions
INTERVENTION OF SAFETY DEVICES
Remember that the engine will stop whenever:
– The operator gets up from the seat and the parking brake is not engaged.
The engine will not start up if:
– The blade is engaged.
Nobody is sitting in the driver’s seat and the parking brake is not engaged.
If the forward lever isn’t at STOP setting.
MAINTENANCE AND LUBRICATION
CAUTION!
- Disconnect the plug be ore per orming any cleaning, maintenance or repair operation.
Always wear suitable clothing and working gloves.
- When the machine or part o it is li ted to carry out maintenance operations, always
remember to use suitable ixing tools such as holders and sa ety locks.
- When carrying out maintenance operations and/or when the machine is tilted without sa ety
locks or supports, never leave it unguarded in places where inexperienced people and
children could have easy access to it.
- Protect the environment: care ully dispose o used oils, petrol and any other pollutant
product!
- E ective maintenance and correct lubrication help to keep the machine ully e icient.
ENGINE
For the lubrication intervals, follow the instructions provided in the engine handbook. In all cases the
oil must be changed a ter the irst 20 working hours, and then every 100 hours or every
season, together with the oil ilter ( ig. 9, oil drain plug; please, use a second key in the ixing
part). Replace the engine oil filter (A, fig. 10). The first precaution is to ensure that the engine is
correctly serviced with the air filter, cooling fins and cylinder head clean and the oil at the correct level.
Check the air filter every 4 hours, or even more often in very dusty environments. Check the engine
cooling intake grid (A, fig. 4).
HYDROSTATIC AXLE
ith the engine cold, check the expansion tank (fig. 10); it must be empty. Clean the hydraulic motor
cooling fans often, every 4 working hours in summer when conditions are very dusty (fig. 5). Replace
oil after the first 50 working hours, then every 200 hours. Use 20 50 engine oil, quantity: 2.5 litres.
To replace the oil follow the instructions below:
1) remove the two plugs (fig. 6)
2) remove the oil filter plug (fig. 12) and check the filter
3) unscrew tank cap (B, fig.10)
4) unscrew the cap marked “Gear Chamber” (fig. 11)
5) add oil in position (B, fig. 10). Fix the cap marked “Gear Chamber” (fig. 11) when oil comes out
6) make sure the expansion tank is empty. Only fill the connection pipe
FRONT WHEEL AXLE
Grease the wheel pivot pins every 20 hours. Lubricate the steering joints. Lubricate the bushing in the
belt stretcher of cutting deck- engine belt (fig. 13).
AIR FILTER
Check the air filter every 4 hours, or more frequently if working in a very dusty environment (fig. 7).
CHECKING THE BLADES AND CUTTING DECK
A blunt blade tears the grass, leaving it unattractive. The cutting edges of both blades must be
sharpened. To remove a blade, take hold of it firmly, wearing work gloves, and unscrew the central
10

Climber 8.22/ Translation of the original instructions
screw, remembering that the screw has a right-hand thread (3 fig. 8). Sharpen both cutting edges
using a medium-grain grinding wheel and check that the blade is balanced by standing it on a round
bar inserted in the central hole. Fit the two cutting blades following the diagram (fig. 8).
CAUTION!
Tighten the fixing screw (3 fig. 8) firmly. Always replace damaged or crooked blades; never attempt to
repair them! hen fitting, always follow the diagram (fig. 8). ALWAYS USE ORIGINAL BLADES! If
they are worn they can be turned round since they have two cutting edges. Always check that the
blade bolts are not worn or damaged.
ADJUSTING THE CUTTING DECK
Levelness of the cutting deck is essential in order to obtain an evenly mown lawn. Park the mower on
a flat surface and check that the tyre pressure is correct. Use the 4 adjustment devices (fig. 17 –
17A), so that the edge of the cutting plate is at the same distance from the floor (100 mm) on both
sides (with the operator sitting on board and the cutting deck in the position no. 1. If you are unable to
level off the deck, contact an authorised After-Sales Service Centre.
BLADE – ENGINE BELT
Make all the checks and adjustments (fig. 16), keeping the deck at the lowest position.
Take care when positioning the belt guides; move them towards the belt, checking the deck at the
various height settings. Check the belt tensioner spring (fig. 18).
HYDROSTATIC AXLE – ENGINE BELTS
These belts are self-adjusting and do not require any adjustment. Simply check the spring tension.
To replace the belts, release the tension spring (fig. 19).
BLADE ROTATION
Rotation is started and stopped using the switch (no. 6, fig. 1).
hen rotation is engaged the engine must be running at medium rpm (see indication on the
accelerator decal) and the machine must not be in the area to be cut. Never start the blades with the
engine at maximum rpm. The machine is equipped with an electromagnetic clutch which also brakes
the blade during disengagement. The blades are also disengaged automatically when the cutting
height adjuster lever is moved to the highest position.
CAUTION: for safety reasons if the operator pushes down the height adjustment lever from the
highest position with the PTO button engaged, the blades do not start automatically. To start the
blade the PTO button must be switched off and switched on again.
The blade must stop within 5 seconds. If this is not the case, adjust the 3 nuts of the electromagnetic
clutch, placing a 0.3 mm feeler gauge under the brake plate. N.B. This operation must be carried
out by an authorized a ter-sales service center.
CHANGING THE BELTS
The movement is transmitted from the motor to the hydraulic transmission and to the blades by
means of two V-belts. Replace the belts as soon as they show signs o wear! Their replacement
and subsequent adjustment are fairly complex procedures and must be carried out by an Authorised
After-Sales Service Centre. To change the cutting deck drive belt remove the belt guide beside the
deck pulley (fig. 17) and release the belt stretcher spring (Fig.19).
ALWAYS USE ORIGINAL BELTS!
TRACTION RELEASE LEVER
The traction release lever is located at the back of the machine (fig. 20). If the machine breaks down,
move the lever to idle position to allow it to be towed or moved by hand (B, fig. 20). In the position (A)
the machine is in working condition.

Climber 8.22/ Translation of the original instructions
LUBRICATION POINTS
MAINTENANCE SUMMARY TABLE
PROCEDURE EVERY 8
HOURS
AFTER
20
HOURS
EVERY
50
HOURS
EVERY
100
HOURS
ONCE A
YEAR OR
EVERY 200
HOURS
Engine oil check the level ●
change ● ●
Air filter check ●
replace ٭
Spark plug check/adjust ●
replace ●
Check that the engine intake grid is
clean ●
Check that the hydraulic engine
colling fins are clean ●
Hydrostatic
axle oil
check the level
● ●
replace ● ●
Check that blades are well-
sharpened and well-fixed ●
Lubricate with grease ● ●
● recommended procedure
٭ procedure to be carried out i necessary
12

Climber 8.22/ Translation of the original instructions
TROUBLE-SHOOTING
PROBLEM
CAUSE REMEDY
Dashboard OFF with key in “AVV.” (ON) pos.
– Battery not supplying power – Check connecting cables
– Recharge battery
– Change the fuse
Dashboard ON, but starter motor does not turn over with key in “AVV” (ON) pos.
– Battery not supplying enough power – Recharge battery
– Start-up go-ahead not given – Travel lever in stop position
– Disengage blades
– Sit in the driver’s seat
– Check the three safety sensors (seat –
blades engagement - feed lever)
Difficult starting or irregular running of engine
– Carburetion problems – Clean or change the air filter
– Adjust the carburettor (follow engine manual
instructions)
– Deposits or dirt in fuel – Empty the tank and use fresh petrol
– Check and change the petrol filter if
necessary
Starter motor turns over but engine does not start
– No petrol flow – Check that the choke has been activated (if
engine is cold)
– Check petrol level in tank
– Check wiring of carburettor opening control
– Check petrol filter (and change if necessary)
- Check that the vent on the tank cap is not
blocked
– Fault in ignition system – Check that the caps of the sparkplugs are
correctly fastened
– Check that the electrodes are clean and at
the correct distance apart.
Drop in engine performance during cutting
– Speed too high for cutting height – Reduce speed
–Raise cutting deck by a few notches
13

Climber 8.22/ Translation of the original instructions
Uneven cutting
– Cutting deck not parallel to ground – Check tyre pressure
– Level off the deck
– Blades fault – Check that the blades are correctly mounted
– Sharpen or change the blades
– Check the tension of the deck motor belt
Vibrations during operation
– Blades unbalanced – Balance blades or replace if damaged
Fastenings are loose – Check and fasten the blade fixing screws as
well as the fixing screws of the engine and
chassis.
ELECTRICAL SYSTEM
The electrical system is protected by a fuse which cuts out the entire electrical system if blown. A ter
inding and repairing the ault, replace the fuse with another of the same rating. Never replace the
use with one o a di erent rating. The electrical system fuses are on the left-hand side of the
steering wheel (fig. 21, B). If problems persist after all the procedures described above have been
carried out, contact the Authorised After-Sales Service Centre. Never attempt to make difficult repairs
unless you have the necessary equipment and technical expertise.
IMPORTANT!
– Take care not to reverse the battery polarity.
– Never operate the mower without the battery, since it is equipped with a charge regulator.
– Take care not to cause short-circuits.
THE MACHINE DOES NOT REMAIN IN NEUTRAL
Adjust the device by loosening the counter-nuts (fig. 22, B) and acting on the central nut (fig. 22, A).
FORWARD LEVER
To adjust the forward and reverse travel speeds, use the screws (A, fig. 23) if the forward lever
automatically returns to zero adjust the self-locking nut (B, fig. 23).
ENDING WORK
After mowing, disengage the blades and drive back with the cutting deck in the highest position. To
stop, move the forward lever to the STOP position (2, fig. 3), set the throttle lever to the minimum rpm,
switch off the engine by turning the key (1, Fig. 1) and lower the deck to the lowest position.
CLEANING
Clean the outside of the mower after each use.
STORAGE AND PROLONGED PERIODS OF DISUSE
Store the mower in a dry place, away from atmospheric agents, and preferably cover with a sheet. If
the mower is not going to be used for a long period (over 1 month), disconnect the red battery cable
(B, fig. 21) and follow the instructions given in the engine manual. Also lubricate all of the articulated
joints. Regularly check that the battery voltage does not drop below 12 volts. If it does, recharge the
battery. Use the preservative additive for unleaded petrol. If the machine is to be out of use for more
than 30 days, drain the fuel from the engine to prevent sticky deposits from forming in the fuel intake
system or in vital parts of carburettor. To protect the engine we advise you to use the Briggs &
Stratton fuel additive, available from all Briggs & Stratton authorised services centres. Add the
additive to the fuel in the tank or in the fuel container. Run the engine a little to circulate the additive
through the carburettor. The engine and carburettor can be stored for up to 24 months. NB.: If no
additive are used or the engine is running on petrol which contains alcohol, drain the fuel tank and run
the engine until there is no fuel left.
14

Climber 8.22/Original instructions- Istruzioni originali- Original-Anleitungen- Instrucciones originales
TRINCIAERBA IDROSTATICO
CLIMBER 8.22
Gentile Cliente,
nel ringraziarla per la fiducia e la preferenza accordata al nostro Grillo CLIMBER, confidiamo c e
l’uso di questa sua nuova macc ina risponda pienamente alle sue esigenze. Per l’impiego ottimale e
per la sua manutenzione nel tempo, la preg iamo di leggere attentamente e seguire scrupolosamente
le indicazioni di questo libretto; ciò le consentirà di ottenere i massimi risultati e salvaguardare la sua
spesa. La preg iamo di conservare questo libretto, c e dovrà sempre accompagnare la macc ina.
DESCRIZIONE GENERALE E USO PREVISTO
La macc ina Grillo Climber 8.22 è un trinciaerba con operatore a bordo, progettato per il taglio
dell'erba, anc e in pendenza.
ATTENZIONE! Leggere a en amen e prima di avviare il mo ore.
Le seguen i avver enze sono impor an i per l’incolumi à dell’opera ore!
AVVERTENZE
La prudenza è l’arma principale nella prevenzione degli incidenti!
La preg iamo vivamente di leggere con attenzione le seguenti avvertenze nell’uso del trinciaerba,
prima ancora di iniziare il lavoro.
L’uso improprio del trinciaerba e il suo equipaggiamento possono risultare pericolosi. Per ridurre tali
risc i, osservare le precauzioni necessarie di seguito riportate:
1) Leggere questo manuale interamente, prima di accendere e mettere in movimento il trinciaerba.
2) Prestare particolare attenzione alle ammonizioni e alle etic ette di sicurezza attorno al
trinciaerba.
3) Prima di fare lavorare con la macc ina altre persone bisogna metterle al corrente delle norme di
sicurezza e di come si usa.
4) Prima d'iniziare il lavoro, indossare indumenti appropriati da lavoro, guanti, scarponi, occ iali.
5) Durante il lavoro indossare adeguati mezzi di protezione acustica (cuffie).
6) Prima di accendere la macc ina, verificare c e non ci siano persone intorno; specialmente
bambini.
7) Prima di partire con la macc ina in marcia indietro, controllare c e non ci siano persone od
ostacoli.
8) Controllare il terreno prima di procedere alla rasatura, c e non vi siano sassi, bastoni o corpi
estranei, c e potrebbero essere scagliati lontano, e risultare quindi molto pericolosi.
9) Se si urta un corpo estraneo, disinnestare la lama, fermare il motore, togliere la c iave di
avviamento e ispezionare il trinciaerba; se la macc ina vibra, farla riparare.
10) Prima di scendere dal trinciaerba, spegnere il motore, disinserire la PTO, rimuovere la c iave
d'avviamento e abbassare il piatto tosaerba nella posizione più bassa.
11) Sui viali sconnessi viaggiare a bassa velocità.
12) Sulle pendenze, in discesa moderare la velocità.
13) In discesa, curvare sempre lentamente.
14) L'utilizzatore è sempre responsabile dei danni arrecati a terzi.
15) I coltelli deformati o danneggiati devono essere sempre sostituiti, mai riparati.
16) Usare sempre ricambi ed accessori originali GRILLO.
17) Lavorare solo con la luce del sole o con buona luce artificiale.
18) Immagazzinare il carburante in contenitori specificatamente costruiti per questo scopo.
19) Fare attenzione quando si lavora vicino ad una strada.
20) Far raffreddare il motore prima di mettere la macc ina in locali c iusi.
21) Non usare la macc ina quando si è affaticati e non bere alcolici.
22) Evitare fuoriuscite di combustibile e dopo aver riempito il serbatoio pulire ogni fuoriuscita sulla
macc ina prima di avviare il motore.
23) Non manomettere o disattivare i dispositivi di sicurezza.
24) Non cambiare le regolazioni del motore, in modo particolare il numero di giri max.
25) Non appoggiare pesi sul sedile, si potrebbe disattivare il dispositivo di sicurezza
15

Climber 8.22/Original instructions- Istruzioni originali- Original-Anleitungen- Instrucciones originales
dell'avviamento.
26) Non fare nessun tipo di regolazione o pulizia col motore in moto.
27) Non fare controllare la macc ina da nessuno mentre siete seduti alla guida col motore in moto.
USI IMPROPRI DA EVITARE
28) Non permettere passeggeri sulla macc ina.
29) Non fare lavorare ragazzi troppo giovani; vietato l'uso ai minori di 16 anni.
30) Non operare col trinciaerba vicino a fossati o banc ine c e si possono rompere sotto il peso
della macc ina, specialmente quando la superficie è staccata o bagnata.
31) Sostituire le marmitte danneggiate o usurate.
ULTERIORI ACCORGIMENTI PER LA SICUREZZA
Le avvertenze sopra riportate potrebbero non essere sufficienti ad evitare ogni risc io, nel caso in cui
l'operatore non si attenesse all'uso appropriato della presente macc ina trinciaerba. Pertanto, per
maggiore prudenza specific iamo quanto segue.
32) La rotazione della lama del trinciaerba è molto pericolosa, non mettere mai le mani o i piedi
sotto al piatto rasaerba.
33) Non fare retromarcia col motore accelerato.
34) E' pericoloso azionare il volante di guida bruscamente, col motore a massimo regime.
35) Prima di avviare il motore riempire il serbatoio di carburante. Fare rifornimento di combustibile
solo all'aperto, spegnere sempre il motore, stare lontano da scintille o fiamme, non fumare!
Riposizionare in modo sicuro il tappo del serbatoio e dei contenitori di carburante.
36) Se dovete svuotare il serbatoio carburante, eseguire l'operazione all'aperto.
37) Non lavorare col trinciaerba sopra alla g iaia c e viene aspirata e centrifugata dalla lama,
risultando molto pericolosa.
38) Se avete dei bambini, quando non usate la macc ina, nascondete la c iave d'avviamento.
39) ATTENZIONE: per ridurre il pericolo d'incendio mantenere il vano motore, la marmitta, i
collettori di scarico, la batteria, la zona serbatoio e conduttura carburante liberi da erba, foglie,
polvere ecc.
40) Non immagazzinare la macc ina dentro un edificio dove i vapori del carburante possono
arrivare a fiamme, scintille o fili elettrici scoperti.
Disinnes are la rasmissione del pia o, spegnere il mo ore e disinserire le candele:
a) prima di pulire i punti ostruiti
b) prima di controllare o riparare il trinciaerba.
c) dopo aver urtato un corpo estraneo (ispezionare l'organo di taglio per verificare c e non sia
danneggiato e ripararlo prima di rimetterlo in funzione).
d) se la macc ina comincia a vibrare in modo anomalo, effettuare immediatamente un controllo
generale per individuare la ragione c e provoca questa anomalia: se necessario ric iedere
l'intervento dell'officina autorizzata.
IDENTIFICAZIONE E ASSISTENZA
IDENTIFICAZIONE
Il Climber 8.22 è fornito di una targ etta posta sul
piantone dello sterzo con il numero di matricola
della macc ina.
SERVIZIO ASSISTENZA
Questo manuale fornisce le indicazioni per l’uso della macc ina e per una corretta manutenzione di
base, eseguibile dall’utilizzatore. Per gli interventi non descritti in questo libretto, interpellare il
Rivenditore di Zona.
RICAMBI
Si raccomanda di impiegare esclusivamente ricambi originali, gli unici c e offrono caratteristic e di
16

Climber 8.22/Original instructions- Istruzioni originali- Original-Anleitungen- Instrucciones originales
sicurezza e intercambiabilità. Ogni ric iesta deve essere corredata del numero di matricola della
macc ina e il numero di codice del pezzo da sostituire. Per i ricambi del motore, attenersi a quanto
indicato nel libretto specifico.
GARANZIA
La garanzia è fornita nei modi e nei limiti indicati dalla legge vigente. Il rivenditore dovrà
obbligatoriamente consegnare il certificato di garanzia della macc ina al cliente finale, stampando
una copia della registrazione dal sito Grillo. Per quanto riguarda il motore, valgono le condizioni
previste dai rispettivi Produttori.
RICAMBI CHE SI CONSIGLIANO DI TENERE DI SCORTA
N. 2 lame
N. 2 viti lame
N. 2 dadi viti lame
N. 1 serie cing ie
N. 1 filtro aria motore
N. 1 filtro olio motore
N. 1 filo acceleratore
N. 2 fusibili impianto
CARATTERISTICHE TECNICHE
MOTORE: BRIGGS & STRATTON 7220 PROFESSIONAL SERIES OHV 656 cc, bicilindrico a
benzina con pompa olio integrata.
AVVIAMENTO: elettrico, con batteria 12V.
CAMBIO: trasmissione idrostatica.
DIFFERENZIALE: con bloccaggio azionato a pedale.
FRIZIONE: elettromagnetica per PTO, con freno lama.
VELOCITÀ: da 0 a 10 km/ a variazione continua e retromarcia da 0 a 6 km/ .
PNEUMATICI an eriori: 3.50-6 TRACTOR; pos eriori: 18 x 9.50-8 TRACTOR.
FRENI: DI SERVIZIO sulle ruote anteriori con comando a pedale; DI STAZIONAMENTO sulle ruote
posteriori con comando a leva.
SEDILE: ammortizzato e regolabile, con roll bar.
PIATTO DI TAGLIO: scarico laterale/posteriore.
SISTEMA DI TAGLIO: 1 lama rotante.
LARGHEZZA DI TAGLIO: 910mm
VELOCITÀ PERIFERICA LAMA: 81 m/sec.
ALTEZZA DI TAGLIO: da 35 mm a 110 mm con 6 diverse posizioni di taglio e 1 di trasferimento.
RESA: 7000 m2/ (indicativa)
RAGGIO INTERNO DI STERZATA: 500 mm.
SERBATOIO: 7 litri - RISERVA: 1 litro.
TIRO TRAINO E FANALE ANTERIORE DI SERIE
ACCESSORI: catene per ruote posteriori, lama neve orientabile manuale 125 cm.
DIMENSIONI: Lung ezza: 1895 mm, Larg ezza: 900 mm, Altezza: 980 mm
PESO: 265 kg
17