Griven Jasper MK2 User manual

Jasper MK2 User Manual
Rev. 1.00
Date: 28/07/2021
page 1 of 7
Griven S.r.l. - Via Bulgaria, 16
46042 Castel Goredo
Mantova - Italy
© Copyright Griven 2020 - GRIVEN S.r.l. is continuously
developing and improving all its products.
We reserve the right to change specifications without
prior notification
Tel. [phone]
E-mail: [email protected]
Web: www.griven.com
AL5400
Dimensions
Power consumption 195 W
Nominal current 0.88A
Power supply 100-277 VAC 50/60Hz
Inrush current 75A @ 230VAC cold start
Power factor cos.φ= 0.94
Electrical class I
Weight 18.3 Kg
Operating temperature From -40°C. to +50°C.
IP rating IP66
IK rating IK10
477
450
6.50
10.50
6.50
60
29.75°
142
495

Jasper MK2 - Rev. 1.00
page 2 of 7
Important notices / Avvertimenti importanti
- This product must be installed in accordance with applicable national and local electrical and construction codes by a person familiar with the construction and
operation of the product and the hazards involved. Failure to comply with the following installation instructions may result in death or serious injury.
Questo prodotto deve essere installato secondo le normative locali, da personale specializzato. La mancata osservanza delle istruzioni di installazione può
portare a situazioni di pericolo all’incolumità della persone.
- Do not stare at the operating light source.
Non fi ssare la sorgente luminosa durante il suo funzionamento.
- The fi xture might be damaged by excess voltage. The installation of an overvoltage protection device on the electrical system (SPD) is recommended for
reduce the risk of damage.
Apparecchiatura sensibile alle sovratensioni. Si consiglia l’installazione di un dispositivo di protezione delle sovratensioni (SPD) sull’impianto elettrico per
attenuare l’intensità di questi fenomeni proteggendo gli apparecchi dal rischio che vengano danneggiati.
- The use of an adequate magnetothermic switch along the power supply line is recommended.
E’ consigliato l’uso di un adeguato interruttore magnetotermico/differenziale sulla linea di alimentazione.
-Connect the fi xtures to each other only when disconnected from mains.
Collegare tra loro i proiettori solo quando nessuno di essi è collegato alla rete elettrica.
- Never leave cables and connectors unconnected or unprotected for long periods.
Non lasciare mai per lungo tempo agli agenti atmosferici cavi e connettori non collegati o non protetti.
- Disconnect power before installing or servicing to avoid electrical shock.
Togliere l’alimentazione prima di effettuare qualsiasi operazione all’interno dell’apparecchiatura.
- Disconnect power before any connection operation.
Togliere l’alimentazione prima di effettuare qualsiasi operazione di connessione tra gli apparecchi.
- Check voltage and frequency before powering the fi xture. Do not exceed fi xture specifi ed voltage.
Prima di connettere l’apparecchio alla rete elettrica, verifi cate la compatibilità di tensione e frequenza.
- Do not handle the unit with wet hands or in wet environments.
Non maneggiate il prodotto con mani bagnate o in presenza di acqua.
- Apply to qualifi ed staff for any maintenance service not described in this instructions manual.
Rivolgersi ad un tecnico qualifi cato per qualsiasi operazione di manutenzione ordinaria non descritta nel presente manuale.
- Do not exceed the maximum quantity of fi xtures per line in order to avoid power surges.
Non superare il numero massimo specifi cato di apparecchi per linea per evitare pericolori sovraccarichi di corrente.
- Before powering the unit, ensure to use cables and connectors with proper section and length, according to its power consumption.
Prima di effettuare le connessioni verifi care la portata dei cavi / connettori e la lunghezza dei cavi tenendo conto dell’assorbimento del prodotto.
- Fix the projector by using screws, hooks or other adequate supports that can bear its weight.
Fissare il proiettore con viti, ganci o altri supporti in grado di sostenerne il peso.
CAUTION: Prolonged staring at the LED source should be avoided by placing the xture in a proper position.
ATTENZIONE! Fissare la sorgente LED per un periodo prolungato va evitato posizionando l’apparecchio nella posizione appropriata.
WARNING ! Fixing and connecting operations must mandatorily be carried out by qualied personnel only !
WARNING ! Make sure that power supply is o before connecting or disconnecting xtures !
ATTENZIONE ! Le operazioni di ssaggio e collegamento devono essere eseguite solo e obbligatoriamente da personale
qualicato!
ATTENZIONE ! Assicurarsi che l’alimentazione sia spenta prima di collegare o scollegare i dispositivi!

Jasper MK2 - Rev. 1.00
page 3 of 7
M6
M10
Connections
Installation
“C” type cable ( Monocable + connectors )
“M” type cable ( Monocable without connectors )
POWER + DMX OUT
POWER + DMX IN
POWER + DMX OUT
A=DMX-
B=DMX+
C=common/comune
1=Neutral/Neutro
2=Live/Fase
3=GND/Terra
POWER + DMX IN
POWER + DMX OUT
Tipo di cavo “C” (Monocavo + connettori )
Tipo di cavo “M” ( Monocavo senza connettori )
RED= DMX +
BLACK= DMX -
WHITE=COMMON
ROSSO= DMX +
BIANCO=COMUNE
NERO= DMX -
BLUE= N (Neutral)
BROWN=L (Live)
YELLOW/GREEN=GND
BLU= N (Neutro)
MARRONE=L (Fase)
GIALLO/VERDE=Terra
POWER + DMX IN
RED= DMX +
BLACK= DMX -
WHITE=COMMON
ROSSO= DMX +
BIANCO=COMUNE
NERO= DMX -
BLUE= N (Neutral)
BROWN=L (Live)
YELLOW/GREEN=GND
BLU= N (Neutro)
MARRONE=L (Fase)
GIALLO/VERDE=Terra

Jasper MK2 - Rev. 1.00
page 4 of 7
Mode Channel Function Value
3
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
4
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
5 0→100% Dimmer 0-255
5
1 0-100% Red 0-255
2 0-100% Green 0-255
3 0-100% Blue 0-255
40-100% White 0-255
5
0% Dimmer 0-5
100-0% Dimmer 6-250
100% Dimmer 251-255
6
No Strobo 0-5
0-100% Strobo 6-250
100% Strobo 251-255
DMX chart
When operating in DMX mode the xture can accept the
following RDM commands:
• Discovery: Upon request of the RDM controller, the xture
signals its own presence (the RDM controller will display
the xture on a list).
• DMX address reading and setting.
• Channels number reading and setting.
• On / O identication: This command is used to identify the
xture you want to get access to (the identication happens
by switching on all the LEDs at full intensity).
• Manufacturer: it displays the name of the manufacturer
(Griven).
• Model description: it displays the xture’s model.
• Software version description: it displays the current version
of the rmware.
• Temperature: it displays the LEDs operating temperature
value.
RDM functions

Jasper MK2 - Rev. 1.00
page 5 of 7
IR Remote Control operations
LOGIN
DMX MODE
DMX MODE SETTING
DMX ADDRESS SETTING
3 = 4 DMX channels mode
4 = 5 DMX channels mode
5 = 6 DMX channels mode
001~512 = OK
FLASH
FLASH FLASH FLASH
= OK
FLASH FLASH
= OK
MASTER/SLAVE
AUTOMATIC
MODE ¹
AUTOMATIC/MASTER
5”→10”→20”→ 40”
40”→ 20”→ 10”→ 5”
001
SLAVE FIXTURE SETTING
= OK
FLASH FLASH FLASH
FLASH
2xFLASH
3xFLASH
4xFLASH
4xFLASH
3xFLASH
2xFLASH
FLASH
FIXED
COLOR
MODE
0%→100%
100%→0%
5’ inactivity = Automatic
LOGOUT
Green-Cyan-Blue-Magen-
ta-Red-Yellow-White.
1 = RED
2= GREEN
3 = BLUE
4 = WHITE
¹WARNING ! In this mode, no other DMX control device must be present along the line.
The xture must be congured only by using AL1321 IR remote control ( sold separately ) or via any
DMX-RDM compatible controller.

Jasper MK2 - Rev. 1.00
page 6 of 7
Conguration example - Monocable with connectors
A
BI
dmx
CDF
E
A
BI
dmx
CD
A
G
A
BI
dmx
CD
H
A
C
I
Multy Chain Conguration using Repower Box
Single Chain Conguration
Multy Chain Conguration using DMX junction Box
A - Power Input CE ver. 220-240 Vac
B - DMX/RDM Controller
C - Start Line Box - AL5058M - without connectors
D - Jasper MK2
E - Connection Cable - AL0148 L=1m
F - DMX Terminator - R 120 Ω
G - Repower Box - AL5167M without connectors
H - DMX Junction Box - AL5059M without connectors
I - DMX Cable - AL0512
CE Colours
Brown
Blue
Yellow/Green
Red
Black
White
USE
Live
Neutral
Ground
DMX Data +
DMX Data -
DMX GND
Max. 10A
per
daisy chain
DMX cable type:
Use a DMX repeater on each 32nd xture of the
daisy chain or in case the total DMX LINE length
exceeds 300m (1000 ft)
Utilizzare un ripetitore DMX ogni 32 apparecchi
della catena o se la lunghezza totale della LINEA
DMX supera i 300 m (1000 piedi)
2x0.34 mm impedance 110,
capacity 43pF/m, resistance 50/Km.
Tipo di cavo DMX:
Max. 10A
per
catena
2x0,34 mm2 impedenza 110,
capacità 43pF / m, resistenza 50 / Km.
F
F
Conguration example - Monocable without connectors
A
BI
dmx
CD
KF
E
A
BI
dmx
CD
KF
A
G
A
BI
dmx
CD
K
H
A
C
I
F
Multy Chain Conguration using Repower Box
Single Chain Conguration
Multy Chain Conguration using DMX junction Box
A - Power Input CE ver. 220-240 Vac
B - DMX/RDM Controller
C - Start Line Box - AL5058M - without connectors
D - Jasper MK2
E - Connection Cable - AL0148 L=1m
F - DMX Terminator - R 120 Ω
G - Repower Box - AL5167M without connectors
H - DMX Junction Box - AL5059M without connectors
I - DMX Cable - AL0512
K - Heat-shrink tubing
CE Colours
Brown
Blue
Yellow/Green
Red
Black
White
USE
Live
Neutral
Ground
DMX Data +
DMX Data -
DMX GND
Max. 10A
per
daisy chain
DMX cable type:
Use a DMX repeater on each 32nd xture of the
daisy chain or in case the total DMX LINE length
exceeds 300m (1000 ft)
Utilizzare un ripetitore DMX ogni 32 apparecchi
della catena o se la lunghezza totale della LINEA
DMX supera i 300 m (1000 piedi)
2x0.34 mm impedance 110,
capacity 43pF/m, resistance 50/Km.
Tipo di cavo DMX:
Max. 10A
per
catena
2x0,34 mm2 impedenza 110,
capacità 43pF / m, resistenza 50 / Km.
MAX 8 UNIT ( 10A)
MAX 8 UNIT ( 10A)

Jasper MK2 - Rev. 1.00
page 7 of 7
AL5169
DMX terminator
other Jasper
fixtures
AL5058/C
Start Line Box
DMX cable
Mains Power
AL5169
DMX terminator
other Jasper
fixtures
AL5058/C
Start Line Box
Mains Power
AL5169
DMX terminator
other Jasper
fixtures
AL5058/C
Start Line Box
DMX cable
Mains Power
AL5169
DMX terminator
other Jasper
fixtures
AL5058/C
Start Line Box
Mains Power
Addr.001 Addr.005 Addr.009 Addr.013 Addr.xxx
DMX
Controller
DMX Mode
Master-Slave/Automatic/Fixed color mode
Addr.001 Addr.001 Addr.001 Addr.001Master