Grizzly T25953 User manual

For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T25953
T-SLOT WORK TABLE
INSTRUCTIONS
For Models Mfd. Since 10/17
COPYRIGHT © JANUARY, 2018 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#BL19338 PRINTED IN CHINA
Introduction
V1.01.18
Description Qty
A. Legs ........................................................... 4
B. Feet M10-1.5 x 136 ..................................... 4
C. Long Braces 38" ......................................... 4
D. Hex Nuts M8-1.25 ..................................... 32
E. Flat Washers 8mm .................................. 32
F. Carriage Bolts M8-1.25 x 12 ..................... 32
G. Wood Screws M4 x 20 ............................ 10
H. Short Braces 26" ........................................ 4
I. T-Slot Table ................................................ 1
Inventory
Specifications
• Top Dimensions ..............................28" x 40"
• Footprint (Length x Width) .......... 381⁄2" x 27"
• T-Track Dimensions .................. 3⁄4"W x 3⁄8"D
• Maximum Weight Capacity ..............700 lbs.
Needed for Setup
• Open-End Wrench or Socket 14mm .......... 1
• Phillips Head Screwdriver #2 ..................... 1
• Assistant ..................................................... 1
Figure 2. T25953 Stand Components.
Figure 1. Model T25953 T-Slot Work Table.
H
Figure 3. T25953 T-Slot Table.
A
BC
D
E
F
H
G
I
The Model T25953 T-Slot Work Table is designed
to support sanding, clamping, routing, assem-
bly, and sawing projects. Workpieces can be
clamped virtually anywhere on the T-slot table
using Grizzly's T-Track Auto Adjust Clamps and
Fence Kits (not included). The T-slots (see inset
for dimensions) are compatible with 5⁄16" bolts.
7/16"
3/16"
5/16"
3/8"

-2- T25953 T-Slot Table (Mfd. Since 10/17)
Assembly
Before beginning the assembly process, refer to
Needed for Setup and gather all listed items.
3. Attach (4) short braces to side assem-
bly with (8) M8-1.25 x 12 carriage bolts,
(8) 8mm flat washers, and (8) M8-1.25 hex
nuts (see Figure 5). Finger-tighten hex nuts
for now.
1. Build one side assembly for stand by
attaching (2) long braces to (2) legs with
(8) M8-1.25 x 12 carriage bolts,
(8) 8mm flat washers, and (8) M8-1.25 hex nuts
(see Figure 4). Finger-tighten hex nuts for
now.
Note: Orient lip of each long brace upward,
and secure long braces to inside edge of legs
(see inset).
To assemble T-slot work table:
2. Repeat Step 1 to build a second side
assembly.
Figure 4. 1 of 2 side assemblies for stand.
x 8
Lip
(Each Side)
Figure 5. Short braces attached to side
assembly.
Lip x 8
Short
Braces
4. Attach second side assembly to short brac-
es with (8) M8-1.25 x 12 carriage bolts,
(8) 8mm flat washers, and (8) M8-1.25 hex
nuts (see Figure 6). The lips of the short
braces normally overlap the lips of the long
braces (see inset of Figure 6).
Leg
Hole
Side
Assembly
Figure 6. Second side assembly attached to
short braces.
x 8 Second
Side
Assembly
Long Brace
End View

T25953 T-Slot Table (Mfd. Since 10/17) -3-
6. Place clean piece of cardboard on ground,
then lay T-slot table face down on cardboard.
7. Place stand assembly on table, align mount-
ing holes, and attach with (10) M4 x 20 wood
screws (see Figure 8).
Figure 7. Feet attached to stand assembly.
8. With help of an assistant, turn work table right
side up. Position table so it is centered over
stand (not leaning to one side or the other).
9. Final tighten all fasteners from Steps 1–4.
10. Loosen (4) M10-1.5 hex nuts on stand feet,
adjust feet to make sure table does not wob-
ble, then tighten hex nuts to secure feet.
Figure 8. T-slot table installed.
5. Remove (1) hex nut from top of each foot
stud, insert stud through hole in bottom of
each leg, then re-install each hex nut to
secure feet (see Figure 7). Bottom (2) hex
nuts should be positioned at same location
on all four studs.
x 10
NOTICE
Refer to our website or latest catalog for
additional recommended accessories.
• Adjustable clamping force of 25-150 lbs.
(T28110) & 25-550 lbs. (T28111)
• Versatile 5⁄16" T-bolt fits standard 5⁄16" T-tracks
• Hardened steel push rod with non-marring
pad on In-Line Clamp
• Lock knob secures clamp to T-track
• Patented mechanism
T-Track Clamps
Accessories
Figure 9. Grizzly T-track clamps.
T28110
T28111
Figure 10. D3347 Heavy-Duty Cam Clamp.
D3347–Heavy-Duty Cam Clamps for T-Tracks
Easy to set up and slides along on tracks. Fits
standard 5⁄16" T-tracks.
Foot

-4- T25953 T-Slot Table (Mfd. Since 10/17)
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.
12
3
4
5
6
7
8
9
10
11
12
grizzly.com
grizzly.com
T25953
T25953
NOTICE
DO NOT exceed maximum
weight capacity of 700 lbs.
NOTICE
DO NOT exceed maximum
weight capacity of 700 lbs.
T25953
T25953
13
14
15
16
17
18
19
20
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT25953001 CARRIAGE BOLT M8-1.25 X 12 11 PT25953011 SHORT BRACE 26" (BOTTOM)
2 PT25953002 FLAT WASHER 8MM 12 PT25953012 LEG
3 PT25953003 HEX NUT M8-1.25 13 PT25953013 NOTICE LABEL
4 PT25953004 WOOD SCREW M4 X 20 14 PT25953014 MODEL NUMBER LABEL
5 PT25953005 FOOT M10-1.5 X 60D (RUBBER) 15 PT25953015 QR CODE LABEL
6 PT25953006 T-SLOT TRACK 120MM 16 PT25953016 GRIZZLY.COM LABEL
7 PT25953007 T-SLOT TRACK 235MM 17 PT25953017 TOUCH-UP PAINT, GLOSSY BLACK
8 PT25953008 T-SLOT TRACK 775MM 18 PT25953018 HEX NUT M10-1.5
9 PT25953009 TABLE TOP 19 PT25953019 LONG BRACE 38" (TOP)
10 PT25953010 LONG BRACE 38" (BOTTOM) 20 PT25953020 SHORT BRACE 26" (TOP)
T25953 Parts Breakdown
BUY PARTS ONLINE AT GRIZZLY.COM!
Scan QR code to visit our Parts Store.