Grizzly T26903 User manual

For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL T26903
521⁄2" 14-DRAWER TOOL CABINET
INSTRUCTIONS
COPYRIGHT © AUGUST, 2014 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
FOR MODELS MANUFACTURED SINCE 08/2014 #WK16750 PRINTED IN CHINA
Introduction
The Model T26903 14-Drawer Tool Cabinet
requires some assembly. Follow instructions
below for assembly, operation, and maintenance.
Inventory Qty
• Tool Cabinet with Drawers ........................... 1
• Handle ......................................................... 1
• Hex Bolts M8-1.25 x 25 ............................. 28
• Flat Washers 8mm .................................... 24
• Lock Washers 8mm ................................... 24
• Fixed Casters .............................................. 2
• Swivel Casters ............................................. 2
• Swivel Casters with Brakes ......................... 2
• Keys ............................................................. 2
Figure 1. Model T26903.
Assembly
1. Attach handle on preferred side of tool cabi-
net using four M8-1.25 x 25 hex bolts (see
Figure 2). Do not over-tighten!
Figure 2. Handle installed.
Handle
x 4
• To reduce risk of crushing injuries from
tool cabinet tipping over on you:
— Do not stand on cabinet or in drawers.
— Push cabinet only. Do not pull it.
— Only open one drawer at a time.
— Only move or transport cabinet with all
drawers closed and locked.
• Do not exceed weight capacities:
— Max individual drawer weight limit
is 50 lbs.
— Max tool cabinet weight limit (including
contents) is 1000 lbs.
• To prevent accidental rolling, always lock
brakes after moving cabinet.
• Do not allow children to have unsupervised
access to cabinet.
V1.08.14

-2- T26903 14-Drawer Tool Chest (Mfd. 08/14)
2. Remove casters and hardware from bottom
drawer.
3. Remove bottom drawer (refer to Operation
for instructions).
4. Place unit on its top or side.
Tip: Use packaging material to protect paint
finish.
5. Attach each caster using four M8-1.25 x 25
hex bolts, 8mm lock washers, and 8mm flat
washers (see Figure 3).
Be sure swivel casters with brakes are mount-
ed on same side as handle, and fixed casters
are mounted in middle of unit, parallel with
long sides of cabinet.
Removing & Installing Drawers
Figure 3. Caster installed.
6. Return tool cabinet to upright position.
Swivel
Caster
x 4
Locking Drawers
Use the included key to lock the drawers. Only
completely closed drawers will lock.
To remove and install drawers:
1. Fully extend drawer and remove contents.
2. Push left locking tab down and hold, then pull
right locking tab up and hold (see Figure 4).
3. Pull drawer out to remove.
4. To re-install, insert drawer runners into slides
and push drawer in until it stops. The lock-
ing tabs will automatically snap into place to
secure the drawer in the slides.
Figure 4. Location of drawer locking tabs.
Right Locking Tab
Left Locking Tab
Maintenance
• Use soft, clean cloth, and standard cleaning
solution to remove grease, dirt, or oil. Do not
use solvents or flammable cleaning liquids.
• Lubricate drawer slides as needed with dry
lubricant.
• Use graphite to lubricate lock annually.
The drawers can be removed and re-installed if
an object inside causes them not to fully close.

T26903 14-Drawer Tool Chest (Mfd. 08/14) -3-
1
2
3
4
14
13
12
5
6
78
Toreducerisk of serious personal injury when using:
1. Read manual before use for full safety, assembly,and adjustment instructions.
2. To reduce risk of tipping chest, do not stand on chest or in drawers, only
open one drawer at a time, and only move after closing and locking all drawers.
3. Do not lift fully loaded chest by side handles.
4. Do not exceed maximum drawer or product weight.
5. Always push chest instead of pulling it, to avoid risk of it tipping over on you.
6. Always set brakes after moving chest.
7. Do not allow unsupervised children to access chest.
9
9
10
11
T26903 Parts Breakdown and List
REF PART # DESCRIPTION
1 PT26903001 HANDLE SET W/HARDWARE
2 PT26903002 LOCK SET W/2 KEYS
3 PT26903003 GRIZZLY NAMEPLATE-MINI
4 PT26903004 DRAWER TRIM 23-5/8"
5 PT26903005 DRAWER SLIDE SET
6 PT26903006 FIXED CASTER SET
7 PT26903007 SWIVEL CASTER SET
8 PT26903008 SWIVEL CASTER SET WITH BRAKE
9 PT26903009 HEX BOLT M8-1.25 X 25
10 PT26903010 LOCK WASHER 8MM
11 PT26903011 FLAT WASHER 8MM
12 PT26903012 WARNING LABEL FOR TOOLBOXES
13 PT26903013 GRIZZLY.COM GOLD LOGO
14 PT26903014 BLACK TOUCH-UP PAINT
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.