Grizzly H6238 User manual

Adjustable Drill
Press Support
MODEL H6238
Introduction
The Model H6238 Adjustable Drill Press Support
(Figure 1) provides stability and control for drilling
long workpieces.
The Model H6238 was carefully packed when
it left our warehouse. If you discover this unit
is damaged after you have signed for delivery,
please immediately call Customer Service at
[phone] for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, you should inventory the
contents.
Inventory (Figure 2)
A. Column Clamp ............................................ 1
B. Clamp Plate ................................................ 1
C. Center Support ........................................... 1
D. Extension Arms .......................................... 2
E. Roller Supports ........................................... 2
F. Lock Knob M10-1.5 .................................... 5
Clamp Hardware ..........................................
—Hex Bolts M8-1.25 x 100 ........................ 2
—Lock Nut M8-1.25 ................................... 1
—Wing Nut M8-1.25 ................................... 1
Figure 2. Inventory.
B
E
A
C
F
D
Figure 1. Adjustable Drill Press Support.
E

1. Use the hex bolts with a lock nut on one side
of the column clamp and a wing nut on the
other side to clamp the drill column as shown
in Figure 3.
ASSEMBLY
Figure 3. Column clamp.
1. Loosen the wing nut on the column clamp
and rotate the drill press support perpendicu-
lar to the drill head. Tighten the wing nut.
2. Place a straightedge on the drill press table
and adjust the roller supports until they are
the same height as the drill press table.
3. Move the extensions in or out as necessary to
accommodate the length of the workpiece.
If you need additional help with these procedures,
call our service department at: [phone].
ADJUSTMENTS
Failure to follow these instructions will
result in serious personal injury:
1. The addition of the Drill Press Support
increases the tipping hazard. Bolt the drill
press to a solid surface to prevent tipping.
2. Make sure the extension arms are inserted at
least 2" into the center support.
3. Use additional supports for extra long or
unusually heavy workpieces.
4. Push extension arms in when not in use to
reduce obstructions in your shop.
5. Center the workpiece to prevent tipping.
6. DO NOT exceed the weight capacity of the
drill press table.
2. Slide the center support into the column
clamp and secure with a lock knob as shown
in Figure 3.
3. Insert the extensions into the central support
and secure with lock knobs (Figure 4).
Figure 4. Support assembly.
4. Slide the roller supports into the extensions
and secure with lock knobs (Figure 4).
Center Support
Column Clamp
Roller Support
Extension Arm

REF PART # DESCRIPTION
1 PH6238001 CLAMP PLATE
2 PH6238002 COLUMN CLAMP
3 PH6238003 CENTER SUPPORT
4 PH6238004 EXTENSION ARM
5 PH6238005 ROLLER SUPPORT BRACKET
REF PART # DESCRIPTION
6 PH6238006 10" ROLLER
7 PB45M HEX BOLT M8-1.25 X 100
8 PLN04M LOCK NUT M8-1.25
9 PWN02M WING NUT M8-1.25
10 PH6238010 LOCK KNOB M10-1.5
COPYRIGHT © AUGUST, 2004 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#EW6462 PRINTED IN CHINA
PARTS BREAKDOWN