Grizzly G0604 User manual

MODEL G0604
6" X 56" JOINTER
OWNER'S MANUAL
COPYRIGHT © JUNE, 2006 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR8349 PRINTED IN CHINA.


















 
 
 






Table of Contents
INTRODUCTION ............................................................................................................................... 3
Foreword .................................................................................................................................... 3
Contact Info ................................................................................................................................ 3
Machine Data Sheet ................................................................................................................... 4
Identification ............................................................................................................................... 5
SECTION 1: SAFETY ....................................................................................................................... 6
Safety Instructions for Machinery ............................................................................................... 6
Additional Safety for Jointers ..................................................................................................... 8
SECTION 2: CIRCUIT REQUIREMENTS ........................................................................................ 9
110V Operation .......................................................................................................................... 9
SECTION 3: SETUP ....................................................................................................................... 10
Setup Safety ............................................................................................................................. 10
Items Needed for Setup ........................................................................................................... 10
Unpacking ................................................................................................................................ 10
Inventory ................................................................................................................................... 11
Hardware Recognition Chart .................................................................................................... 12
Cleanup .................................................................................................................................... 13
Site Considerations .................................................................................................................. 13
Wheel Assembly ...................................................................................................................... 13
Jointer ....................................................................................................................................... 14
V-Belt ........................................................................................................................................ 14
Checking Outfeed Table Height ............................................................................................... 15
Extension Table ....................................................................................................................... 16
Fence ....................................................................................................................................... 17
Cutterhead Guard .................................................................................................................... 18
Pedestal Switch ........................................................................................................................ 18
Knife Setting Jig ....................................................................................................................... 19
Dust Port .................................................................................................................................. 19
Test Run ................................................................................................................................... 20
Recommended Adjustments .................................................................................................... 20
SECTION 4: OPERATIONS ........................................................................................................... 21
Operation Safety ...................................................................................................................... 21
Basic Controls .......................................................................................................................... 21
Stock Inspection and Requirements ........................................................................................ 22
Squaring Stock ......................................................................................................................... 23
Surface Planing ........................................................................................................................ 24
Edge Jointing ........................................................................................................................... 25
Bevel Cutting ............................................................................................................................ 26
SECTION 5: ACCESSORIES ......................................................................................................... 27
SECTION 6: MAINTENANCE ........................................................................................................ 30
Schedule .................................................................................................................................. 30
V-Belt ........................................................................................................................................ 30
Cleaning ................................................................................................................................... 30
Lubrication ................................................................................................................................ 30

SECTION 7: SERVICE ................................................................................................................... 31
Troubleshooting Guide ............................................................................................................. 31
Inspecting Knives ..................................................................................................................... 33
Adjusting/Replacing Knives ...................................................................................................... 33
Checking/Adjusting Table Parallelism ...................................................................................... 36
Setting Outfeed Table Height ................................................................................................... 38
Setting Infeed Table ................................................................................................................. 39
Calibrating Depth Scale ........................................................................................................... 40
Setting Fence Stops ................................................................................................................. 40
Wiring Diagram ........................................................................................................................ 42
Electrical Components ............................................................................................................. 42
Jointer Parts Breakdown .......................................................................................................... 43
Jointer Parts List ...................................................................................................................... 44
Stand/Motor Parts Breakdown ................................................................................................. 46
Stand/Motor Parts List .............................................................................................................. 47
Warning Label Parts List .......................................................................................................... 48
WARRANTY AND RETURNS ........................................................................................................ 49

G0604 6" X 56" Jointer -3-
If you have any comments regarding this manual,
please write to us at the address below:
Grizzly Industrial, Inc.
C/O Technical Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
We stand behind our machines. If you have any
service questions or parts requests, please call or
write us at the location listed below.
Grizzly Industrial, Inc.
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
Web Site: http://www.grizzly.com
Foreword
INTRODUCTION
Contact Info
We are proud to offer the Model G0604 6" X 56"
Jointer. This machine is part of a growing Grizzly
family of fine woodworking machinery. When
used according to the guidelines set forth in this
manual, you can expect years of trouble-free,
enjoyable operation and proof of Grizzly’s com-
mitment to customer satisfaction.
We are pleased to provide this manual with
the Model G0604. It was written to guide you
through assembly, review safety considerations,
and cover general operating procedures. It repre-
sents our effort to produce the best documenta-
tion possible.
The specifications, drawings, and photographs
illustrated in this manual represent the Model
G0604 as supplied when the manual was pre-
pared. However, owing to Grizzly’s policy of con-
tinuous improvement, changes may be made at
any time with no obligation on the part of Grizzly.
For your convenience, we always keep current
Grizzly manuals available on our website at www.
grizzly.com. Any updates to your machine will be
reflected in these manuals as soon as they are
complete. Visit our site often to check for the lat-
est updates to this manual!

-4- G0604 6" X 56" Jointer
Design Type: .................................................................................................... Floor Model
Overall Dimensions:
Table Size .............................................................................................. 6" W x 551⁄2" L
Height (from floor to table) ....................................................................................321⁄2"
Table Length .........................................................................................................551⁄2"
Table Width ................................................................................................................6"
Shipping Weight ............................................................................................... 347 lbs.
Net Weight ....................................................................................................... 320 lbs.
1st Box Size ................................................................................... 29"L x 18"W x 28"H
2nd Box Size ................................................................................... 62"L x 21"W x 14"H
Stand Footprint .......................................................................................27"W x 20
1⁄2"D
Cutterhead ..........................................................................................................4-Knife
Cutterhead Diameter ..................................................................................................3"
Cutterhead Knife Size ............................................................................... 6" x 5⁄8" x 1⁄8"
Capacities:
Maximum Depth of Cut (per pass) ............................................................................ 1⁄8"
Maximum Width of Cut ...............................................................................................6"
Cutterhead Speed ........................................................................................ 4850 RPM
Cuts Per Minute ................................................................................................. 19,400
Construction:
Tables ................................................................................ Precision Ground Cast Iron
Fence Assembly ............................................................................................. Cast Iron
Body Assembly ............................................................................................... Cast Iron
Stand ................................................................................................... Preformed Steel
Guard ............................................................................................................. Aluminum
Bearings ................................................................................. Shielded and Lubricated
Motor:
Type ............................................................................TEFC Capacitor Start Induction
Horsepower ........................................................................................................... 1 HP
Phase ⁄ Voltage ............................................................................ Single-Phase / 110V
Amps .......................................................................................................................13A
Cycle ⁄ RPM ................................................................................. 60 Hertz / 3450 RPM
Power Transfer .............................................................................................. Belt Drive
Bearings ................................................................................. Shielded and Lubricated
Sound Rating .......................................................................................................80 dB
Features:
...................................................................................Parallelogram Table Adjustment
...........................................................................................Top Mount Switch Controls
...................................................................................... Fence Stops at 45°, 90°, 135°
.................................................................................................... Included 4" Dust Port
....................................................................................................Included Push Blocks
............................................................................................. Included Knife Setting Jig
Specifications, while deemed accurate, are not guaranteed.
MODEL G0604 6" X 56" Jointer
Customer Service #: [phone] • To Order Call: [phone] • Fax #: [phone]
MACHINE DATA
SHEET
Machine Data Sheet

G0604 6" X 56" Jointer -5-
A
A. Outfeed Table
B. Fence
C. Fence Lock
D. Fence Tilt Lock
E. Cutterhead Guard
F. Fence Tilt Handle
G. Control Panel
H. Infeed Table
I. Infeed Table Adjustment Lever
J. Mobile Base Lock
K. Depth Scale
L. Infeed Table Lock
M. Outfeed Table Lock
N. Outfeed Table Adjustment Lever
Identification
BD
E
G
H
I
K
L
C
M
N
J
F

-6- G0604 6" X 56" Jointer
4. ALWAYS USE HEARING PROTECTION
WHEN OPERATING MACHINERY.
Machinery noise can cause permanent
hearing damage.
5. WEAR PROPER APPAREL. DO NOT
wear loose clothing, gloves, neckties, rings,
or jewelry which may get caught in moving
parts. Wear protective hair covering to con-
tain long hair and wear non-slip footwear.
6. NEVER OPERATE MACHINERY WHEN
TIRED, OR UNDER THE INFLUENCE OF
DRUGS OR ALCOHOL. Be mentally alert
at all times when running machinery.
1. READ THROUGH THE ENTIRE MANUAL
BEFORE STARTING MACHINERY.
Machinery presents serious injury hazards
to untrained users.
2. ALWAYS USE ANSI APPROVED
SAFETY GLASSES WHEN OPERATING
MACHINERY. Everyday eyeglasses only
have impact resistant lenses—they are
NOT safety glasses.
3. ALWAYS WEAR AN ANSI APPROVED
RESPIRATOR WHEN OPERATING
MACHINERY THAT PRODUCES DUST.
Wood dust is a carcinogen and can cause
cancer and severe respiratory illnesses.
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions. This
manual uses a series of symbols and signal words which are intended to convey the level of
importance of the safety messages. The progression of symbols is described below. Remember
that safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY

G0604 6" X 56" Jointer -7-
7. ONLY ALLOW TRAINED AND PROP-
ERLY SUPERVISED PERSONNEL TO
OPERATE MACHINERY. Make sure
operation instructions are safe and clearly
understood.
8. KEEP CHILDREN AND VISITORS AWAY.
Keep all children and visitors a safe dis-
tance from the work area.
9. MAKE WORKSHOP CHILD PROOF. Use
padlocks, master switches, and remove
start switch keys.
10. NEVER LEAVE WHEN MACHINE IS
RUNNING. Turn power OFF and allow all
moving parts to come to a complete stop
before leaving machine unattended.
11. DO NOT USE IN DANGEROUS
ENVIRONMENTS. DO NOT use machin-
ery in damp, wet locations, or where any
flammable or noxious fumes may exist.
12. KEEP WORK AREA CLEAN AND WELL
LIT. Clutter and dark shadows may cause
accidents.
13. USE A GROUNDED EXTENSION CORD
RATED FOR THE MACHINE AMPERAGE.
Undersized cords overheat and lose power.
Replace extension cords if they become
damaged.
14.
ALWAYS DISCONNECT FROM POWER
SOURCE BEFORE SERVICING
MACHINERY. Make sure switch is in
OFF
position before reconnecting.
15. MAINTAIN MACHINERY WITH CARE.
Keep blades sharp and clean for best and
safest performance. Follow instructions for
lubricating and changing accessories.
16. MAKE SURE GUARDS ARE IN PLACE
AND WORK CORRECTLY BEFORE
USING MACHINERY.
Safety Instructions for Machinery
17. REMOVE ADJUSTING KEYS AND
WRENCHES. Make a habit of checking for
keys and adjusting wrenches before turn-
ing machinery ON.
18. CHECK FOR DAMAGED PARTS
BEFORE USING MACHINERY. Check
for binding and alignment of parts, broken
parts, part mounting, loose bolts, and any
other conditions that may affect machine
operation. Repair or replace damaged
parts.
19. USE RECOMMENDED ACCESSORIES.
Refer to the instruction manual for recom-
mended accessories. The use of improper
accessories may cause risk of injury.
20. DO NOT FORCE MACHINERY. Work at
the speed for which the machine or acces-
sory was designed.
21. SECURE WORKPIECE. Use clamps or
a vise to hold the workpiece when practi-
cal. A secured workpiece protects your
hands and frees both hands to operate the
machine.
22. DO NOT OVERREACH. Keep proper foot-
ing and balance at all times.
23. MANY MACHINES WILL EJECT THE
WORKPIECE TOWARD THE OPERATOR.
Know and avoid conditions that cause the
workpiece to "kickback."
24. ALWAYS LOCK MOBILE BASES
(IF USED) BEFORE OPERATING
MACHINERY.
25. BE AWARE THAT CERTAIN WOODS
MAY CAUSE AN ALLERGIC REACTION
in people and animals, especially when
exposed to fine dust. Make sure you
know what type of wood dust you will be
exposed to and always wear an approved
respirator.

-8- G0604 6" X 56" Jointer
Additional Safety for Jointers
No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machines there is danger associ-
ated with the Model G0604. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to lessen the pos-
sibility of operator injury. If normal safety
precautions are overlooked or ignored, seri-
ous personal injury may occur.
1. JOINTER KICKBACK. "Kickback" is when
the workpiece is thrown off the jointer table
by the force of the cutterhead. Always use
push blocks and safety glasses to reduce
the likelihood of injury from kickback. If you
do not understand what kickback is, or how
it occurs, DO NOT operate this machine.
2. OUTFEED TABLE ALIGNMENT. Keep the
top surface of the outfeed table aligned with
the knives at top dead center (the highest
point during rotation) to avoid kickback and
personal injuries.
3. PUSH BLOCKS. Always use push blocks
whenever surface planing. Never pass your
hands directly over the cutterhead without a
push block.
4. WORKPIECE SUPPORT. Supporting the
workpiece adequately at all times while
cutting is crucial for making safe cuts and
avoiding injury. Never attempt to make a cut
with an unstable workpiece.
5. USING GOOD STOCK. Jointing safety
begins with your lumber. Inspect your
stock carefully before you feed it over the
cutterhead. Never joint a board that has
loose knots, nails, or staples. If you have
any doubts about the stability or structural
integrity of your stock, DO NOT joint it!
6. KICKBACK ZONE. The "kickback zone"
is the path directly through the end of the
infeed table. Never stand or allow others to
stand in this area during operation.
7. MAXIMUM CUTTING DEPTH. The maxi-
mum cutting depth for one pass is 1⁄8".
Never attempt any single cut deeper!
8. JOINTING WITH THE GRAIN. Jointing
against the grain or jointing end grain is
dangerous and could produce chatter or
excessive chip out. Always joint with the
grain.
9. GUARDS IN PLACE. All operations must
be performed with the guard in place.
10. PROPER CUTTING. When cutting, always
keep the workpiece moving toward the
outfeed table until the workpiece has passed
completely over the cutterhead. Never back
the work toward the infeed table.
11. SAFE KNIFE PROJECTION. Knives should
never be set in the cutterhead so they proj-
ect more than 0.125" (1⁄8"). Incorrectly set
knives may come loose during operation,
may become damaged, or may damage the
cutterhead.
12. MOBILE BASE. Always lock the mobile
base wheel before operating.

G0604 6" X 56" Jointer -9-
Figure 1. NEMA 5-15 plug and receptacle.
Serious personal injury could occur if you
connect the machine to the power source
before you have completed the set up pro-
cess. DO NOT connect the machine to the
power source until instructed to do so.
110V Operation Grounding
In the event of an electrical short, grounding
reduces the risk of electric shock. This tool is
equipped with a power cord that has a grounding
wire, which must be properly connected to the
grounding prong on the plug; likewise, the outlet
must be properly installed and grounded. All elec-
trical connections must be made in accordance
with local codes and ordinances.
Amperage Draw
The Model G0604 motor draws the following
amps under maximum load:
Maximum Load ...................................... 13 Amps
Circuit Requirements
We recommend connecting this machine to a
dedicated circuit with a verified ground, using the
circuit size given below. Never replace a circuit
breaker with one of higher amperage without con-
sulting a qualified electrician to ensure compli-
ance with wiring codes. If you are unsure about
the wiring codes in your area or you plan to
connect your machine to a shared circuit, you
may create a fire hazard—consult a qualified
electrician to reduce this risk.
Recommended Circuit Size ...................15 Amps
Plug/Receptacle Type
Included Plug/Receptacle ................ NEMA 5-15
SECTION 2: CIRCUIT REQUIREMENTS
Electrocution or fire could
result if this machine is
not grounded correctly
or if your electrical con-
figuration does not com-
ply with local and state
codes. Ensure compliance
by checking with a quali-
fied electrician!
Extension Cords
We do not recommend the use of extension
cords. Instead, arrange the placement of your
equipment and the installed wiring to eliminate
the need for extension cords.
If you must use an extension cord at 110V with
your machine:
• Use at least a 14 gauge cord that does not
exceed 50 feet in length!
• The extension cord must also contain a
ground wire and plug pin.
• Avoid cords over 50 feet long unless they
have been sized by a qualified electrician.

-10- G0604 6" X 56" Jointer
Wear safety glasses dur-
ing the entire set up pro-
cess!
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Setup Safety
SECTION 3: SETUP
The jointer assembly
is very heavy. DO NOT
over-exert yourself while
unpacking or moving
your machine—get assis-
tance.
The following items are needed to complete the
setup process, but are not included with your
machine:
DESCRIPTION Qty
• People for Lifting ........................................ 2
• Straightedge (see Page 28) ....................... 1
• Phillips Screwdriver #2 ............................... 1
• Wrench or Socket 17mm ............................ 2
• Wrench or Socket 14mm ............................ 1
• Wrench or Socket 13mm ............................ 1
• Wrench or Socket 12mm ............................ 1
• Degreaser ................................... As Needed
• Rags for Cleaning ...................... As Needed
Items Needed for
Setup
The Model G0604 was carefully packed when it
left our warehouse. If you discover the machine
is damaged after you have signed for delivery,
please immediately call Customer Service at
[phone] for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the con-
dition of your shipment, you should inventory the
contents.
Unpacking

G0604 6" X 56" Jointer -11-
After all the parts have been removed from the
two boxes, you should have the following items:
Jointer Box: (Figure 2) Qty
A. Jointer Assembly ........................................ 1
B. Carriage ...................................................... 1
C. Fence ......................................................... 1
D. Extension Table .......................................... 1
E. Push Blocks ................................................ 2
F. Cutterhead Guard ....................................... 1
G. Tool Hardware Bag
—
Hex Wrenches 2.5, 4, 5, 6, 8mm ...1 Each
—Open-end Wrench 8/10mm .................... 1
H. Knife Setting Jig (not shown) ..................... 1
Stand Box: (Figure 3) Qty
I. Stand Assembly w/Motor ........................... 1
J. Pedestal Switch .......................................... 1
K. Dust Port .................................................... 1
L. Wheel Assembly ......................................... 1
M. Belt Guard .................................................. 1
N. V-Belt .......................................................... 1
Assembly Fasteners Qty
• Hex Bolt M8-1.25 x 50 (Wheel/Stand) ....... 1
• Flat Washer 8mm (Wheel/Stand) ............... 1
• Hex Bolts M10-1.5 x 55 (Wheel/Stand) ...... 2
• Flat Washers 10mm (Wheel/Stand) ........... 2
• Hex Nuts M10-1.5 (Wheel/Stand) .............. 2
• Cap Screws M8-1.25 x 25 (Jointer/Stand) . 4
• Lock Washers 8mm (Jointer/Stand) ........... 4
• Flange Bolts M6-1 x 12 (Belt Guard) ......... 2
• Hex Nuts 6mm (Belt Guard) ....................... 2
• Flat Washers 6mm (Belt Guard) ................ 2
• Cap Screws M8-1.25 x 30 (Fence) ............ 2
• Cap Screws M8-1.25 x 20 (Pedestal) ........ 2
• Lock Washers 8mm (Pedestal) .................. 2
• Flat Washers 8mm (Pedestal) .................... 2
• Phillips Screws M5-.8 x 16 (Dust Port) ...... 4
• Flat Washers 5mm (Dust Port) .................. 4
• Cap Screws M10-1.5 x 30 (Carriage) ........ 2
• Flat Washers 10mm (Carriage) .................. 2
• Cap Screws M6-1 x 20 (Ext Table) ............ 2
Figure 2. Box 1 inventory contents.
Figure 3. Box 2 inventory contents.
A
BC
F
K
J
Inventory
D
E
G
L
M
N
I
In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or for the sake of expedi-
ency, replacements can be obtained at your local
hardware store.
NOTICE
Some assembly fasteners may arrive pre-
installed on the machine. Check the mount-
ing locations on the machine before assum-
ing that any items from the inventory list are
missing.

-12- G0604 6" X 56" Jointer
Hardware Recognition Chart

G0604 6" X 56" Jointer -13-
Figure 4. Model G0604 overhead view
dimensions.
Machine Placement
Consider the jointer dimensions and size of mate-
rial to be processed through each machine, and
space for auxiliary stands, work tables or other
machinery when establishing a location for your
jointer. See Figure 4 for the Model G0604 over-
head view dimensions.
The unpainted cast iron surfaces are coated with
a waxy oil to protect them from corrosion during
shipment. Remove this protective coating with a
solvent cleaner or citrus-based degreaser such
as Grizzly’s G7895 Degreaser. To clean thor-
oughly, some parts may need to be removed. For
optimum performance from your machine,
make sure you clean all moving parts or slid-
ing contact surfaces that are coated. Avoid
chlorine-based solvents, such as acetone or
brake parts cleaner, as they may damage painted
surfaces should they come in contact.
Site Considerations
Cleanup
551⁄2"
25"
Components and Hardware Needed: Qty
Wheel Assembly ................................................ 1
Stand Assembly w/Motor ................................... 1
Hex Bolt M8-1.25 x 50 ....................................... 1
Flat Washer 8mm .............................................. 1
Hex Bolts M10-1.5 x 55 ..................................... 2
Flat Washers 10mm .......................................... 2
Hex Nuts M10-1.5 ............................................. 2
To attach the wheel:
1. Carefully lay the stand on its side so you can
access the underside.
2. Bolt the wheel assembly to the stand with the
provided hardware as shown in Figure 5.
Wheel Assembly
Figure 5. Bolting the wheel assembly to the
stand.
3. Turn the stand rightside up.

-14- G0604 6" X 56" Jointer
Components and Hardware Needed: Qty
Jointer Assembly ............................................... 1
Stand Assembly w/Motor ................................... 1
Cap Screws M8-1.25 x 25 ................................. 4
Lock Washers 8mm ........................................... 4
To mount the jointer to the stand:
1. Remove the rear cover from the jointer
stand.
2. With the help of an assistant, lift the jointer
onto the stand.
3. Align the mounting holes on the jointer and
stand.
4. Secure the jointer to the stand with the cap
screws and washers as shown in Figure 6.
The jointer is heavy. Seek
assistance when lifting it
onto the jointer stand.
Components and Hardware Needed: Qty
V-Belt ................................................................. 1
Belt Guard ......................................................... 1
Flange Bolts M6-1 x 12 ..................................... 2
Hex Nuts 6mm ................................................... 2
Flat Washers 6mm ............................................ 2
To install the V-belt:
1. Loosen the motor bracket fasteners shown in
Figure 7.
Jointer V-Belt
2. Slide the motor upward and place the V-belt
around the cutterhead pulley and the motor
pulley.
3. Slide the motor down to tension the V-belt.
4. Visually check the alignment of the two pul-
leys to make sure that they are aligned and
that the V-belt is straight up and down (see
Figure 8).
— If the pulleys are aligned, tighten the motor
bracket fasteners and go to Step 8.
— If the pulleys are NOT aligned, perform
Steps 5–7.
Figure 6. Securing jointer to stand.
Figure 7. Motor bracket fasteners (black arrows);
motor mount fasteners (white arrows).

G0604 6" X 56" Jointer -15-
Figure 9. Installing belt guard.
Belt
Guard
Figure 10. Cutterhead knife at top dead center.


Checking Outfeed
Table Height
The outfeed table MUST be level with the knives
when they are at top dead center (their highest
point during rotation) or the workpiece cannot be
fed across the jointer safely.
To check the outfeed table height:
1. Place a straightedge on the outfeed table so it
extends over the cutterhead.
2. Rotate the cutterhead pulley until one of the
knives is at top dead center, as illustrated in
Figure 10.
5. Remove the V-belt and loosen the motor
mount fasteners.
6. Shift the motor horizontally as needed to align
the motor pulley with the cutterhead pulley,
then replace and retension the V-belt.
7. Tighten the motor mount fasteners.
8. Install the belt guard with the flange bolts,
washers, and hex nuts (Figure 9).
9. Replace the access panel on the stand.
The belt guard MUST be installed before
operating the jointer or the moving V-belt
will be exposed, creating an entanglement
hazard at the back of the jointer.
Figure 8. Pulleys aligned.
Cutterhead
Pulley
Motor
Pulley


-16- G0604 6" X 56" Jointer
When correctly set, the knife will barely touch
the straightedge, as shown in Figure 11.
—If your outfeed table is correctly set, no
adjustments are necessary.
—If the knife lifts the straightedge off the
table or it is below the straightedge, then
the outfeed table must be reset. Refer to
Setting Outfeed Table Height on Page
38.
Extension Table
Components and Hardware Needed: Qty
Extension Table ................................................. 1
Cap Screws M6-1 x 20 ...................................... 2
To install the extension table:
1. Attach the extension table to the infeed table
with the cap screws, as shown in Figure 12,
but do not fully tighten the cap screws yet.
Figure 12. Installing extension table.
2. Use the straightedge to adjust the extension
table flush with the infeed table.
3. Tighten the cap screws.
Figure 11. Using a straightedge to align outfeed
table height with knife at TDC.

 

G0604 6" X 56" Jointer -17-
Fence
Figure 15. Attaching fence to carriage.
3. Attach the fence to the carriage, as shown in
Figure 15.
Components and Hardware Needed: Qty
Carriage ............................................................. 1
Fence ................................................................. 1
Cap Screws M10-1.5 x 30 ................................. 2
Flat Washers 10mm .......................................... 2
Cap Screws M8-1.25 x 30 ................................. 2
To install the fence:
1. Attach the fence carriage to the back of the
table base (see Figure 13), but do not fully
tighten the bolts yet.
Figure 16. Installing the fence tilt lever.
4. Install the tilt lever as shown in Figure 16.
Figure 13. Fence carriage installed.
2. Place a piece of paper on the table and slide
the carriage over the table top to allow it to
rest on the paper and self align, as shown in
Figure 14, then tighten the carriage mounting
bolts.
Note: The paper will keep the carriage from
making direct contact with the table, which
will keep the fence from dragging across the
table when it is installed.
Figure 14. Carriage slide propped up on paper.

-18- G0604 6" X 56" Jointer
Cutterhead Guard
Figure 17. Installing the cutterhead guard.
3. Pull the cutterhead guard backward to ten-
sion the spring, then—while holding tension
on the guard—move the fence into regular
operating position and release the guard
against the fence.
4. Test the guard. When pulled back and
released, the guard should spring back over
the cutterhead and stop against the fence.
—If the guard does not spring back over the
cutterhead or drags across the table, rein-
stall it, making sure there is tension on the
shaft when it is installed, so it will spring
back over the fence.
Components and Hardware Needed: Qty
Cutterhead Guard .............................................. 1
To install the cutterhead guard:
1. Move the fence all the way back, then raise it
2" off the table and lock it in place.
2. Insert cutterhead guard shaft so the flat is fac-
ing the set screw, then tighten the set screw
against the shaft (see Figure 17), keeping
the guard approximately 1⁄8" off the table.
Components and Hardware Needed: Qty
Pedestal Switch ................................................. 1
Cap Screws M8-1.25 x 20 ................................. 2
Lock Washers 8mm ........................................... 2
Flat Washers 8mm ............................................ 2
To install the pedestal switch:
1. Attach the pedestal switch with the cap
screws, lock washers, and flat washers, as
shown in Figure 18.
Pedestal Switch
The cutterhead guard is a critical safety fea-
ture on this machine—you MUST install and
verify its operation before using the joint-
er! Failure to install this guard will greatly
increase the chances of a serious injury.
Figure 18. Attaching pedestal switch to stand.
2. Thread the excess motor cord through the
access hole in the stand, and plug it into the
switch cord.