Grizzly H2870 User manual

COPYRIGHT © OCTOBER, 2001 BY GRIZZLY INDUSTRIAL, INC., REVISED AUGUST, 2014 (WK)
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#WK3825 PRINTED IN CHINA
Assembly
For questions or help with this product contact Tech Support at [phone] or [e-mail]
MODEL H2870
6-TON HYDRAULIC PRESS
INSTRUCTIONS
Eye injury hazard! Always
wear safety glasses when
using this machine.
This shop press is not a toy. DO NOT allow
children to use this press. Serious injury
may occur if this press is used incorrectly.
Off-center loads can cause parts to be
ejected unexpectedly, striking operator or
bystanders with great force. STOP and
release compression if workpiece tilts or
binds during compression.
Description Qty
Additional People ................................................. 1
Safety Glasses ............................................... 1 Ea
Open-End Wrenches 13, 16, 18, 19mm ....... 1 Ea
Figure 1. Model H2870.
Needed For Setup
1. Use (4) M10-1.5 x 30 hex bolts, 10mm flat
washers, and M10-1.25 hex nuts to assemble
base supports (#1) to press frame (#5). Have
a helper hold press frame in upright position
until base supports are securely fastened.
2. Align holes in press bed platform (#3) with
highest set of holes in press frame (#5), and
insert support pins (#2) through aligned holes
of bed and frame.
3. Install two eye bolts (#9) into press plate
(#8V2), and secure each eye bolt with an
8mm flat washer and M8-1.25 hex nut.
4. Hook each spring to mounting holes on
underside of frame top.
5. Carefully slide press plate shaft (#8V2)
through frame cross brace, and attach springs
to eye bolts.
6. Fit top of bottle jack (#7V2) into recess on
underside of frame top (#5).
7. Mount base of jack to top of press plate
(#8V2) using (2) M8-1.25 x 25 hex bolts,
8mm flat washers, 8mm lock washers, and
M8-1.25 hex nuts. Slide jack handle (#15)
into bottle jack sleeve.
8. Lay press blocks (#4) across press bed plat-
form (#3). The hydraulic press is now ready
for use.
To assemble press:
Use parts breakdown and list on following page
(with corresponding parts numbers included in
parenthesis below) for guidance while completing
each step.

-2- H2870 6-Ton Hydraulic Press (Mfd. 5/14)
5
7V2
6
9
14
10
8V2
4
3
2
11
13
12
1
15
16
17
14
H2870 Parts Breakdown and List
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PH2870001 BASE SUPPORT 10 PH2870010 HEX NUT M8-1.25
2 PH2870002 SUPPORT PIN 11 PH2870011 HEX BOLT M10-1.5 X 30
3 PH2870003 PRESS BED PLATFORM 12 PH2870012 HEX NUT M10-1.5
4 PH2870004 PRESS BLOCKS 13 PH2870013 FLAT WASHER 10MM
5 PH2870005 FRAME 14 PH2870014 FLAT WASHER 8MM
6 PH2870006 EXTENSION SPRING 15 PH2870015 JACK HANDLE
7V2 PH2870007V2 BOTTLE JACK V2.05.14 16 PH2870016 HEX BOLT M8-1.25 X 25
8V2 PH2870008V2 PRESS PLATE V2.05.14 17 PH2870017 LOCK WASHER 8MM
9 PH2870009 EYE BOLT M8-1.25 X 20
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call [phone] or visit our online parts store at www.grizzly.com to check for availability.