Grizzly T10050 User manual

Inventory (Figure 2)
A. Bender (not shown) .................................... 1
B. Bender Handle ........................................... 1
C. Work Stop Rod ........................................... 1
D. Hex Bolts M10-1.5 x 40 (Handle) ............... 2
E. Flat Washers 10mm (Handle) .................... 2
F. Work Stop ................................................... 1
G. Work Stop Knob ......................................... 1
H. Hex Nut M12-1.75 (Work Stop Rod) .......... 1
Specifications
Maximum Workpiece Thickness ........ 3 Ga.(15⁄64")
Maximum Workpiece Width ..............................4"
Machine Weight .........................................81 lbs.
MODEL T10050
RIGHT ANGLE
IRON BENDER
INSTRUCTIONS
Figure 1. Model T10050.
Damage to your eyes, face, and hands could
result from using this item without proper
protective gear, such as safety glasses or a
face shield, and gloves.
Copy RiGHT © July, 2008 By G Rizzly iNdu STRial, iNC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#JB10791 pRiNTed i N CHiNa
Figure 2. inventory.
If you need help with your new machine, call our
Tech Support at: [phone].
BC
d
e
F
G
H

 
Figure 3. 
Identification
Illustration Legend (Figure 4)




       
       

7daY!hda^Ya^cZh^cY^XViZi]Vii]^h
XdbedcZci^hjhZY^ci]^hhiZe#
A^\]i!YVh]ZYa^cZh^cY^XViZi]Vii]^h
XdbedcZci^hcdijhZY^ci]^hhiZe#
6ggdlh^cY^XViZi]ZY^gZXi^dcd[
bdkZbZcid[VXdbedcZci#
GdiVi^dcVaVggdlh^cY^XViZi]ZY^gZXi^dcV
XdbedcZcibjhiWZijgcZY#
8L28adX`l^hZ
88L28djciZgXadX`l^hZ
8L
88L
88L
Figure 4. Illustration Legend.










 
Assembly


To assemble the machine:
1.       
        
Figure 5
Figure 5. Attaching handle.




2. 

Figure 6
Figure 6. Attaching work stop rod.


3. 
        
Figure7
Figure 7. Work stop.




 
Mounting Operations
       


      
       
         

      

      
         

-ACHINE"ASE
7ORKBENCH
7dai
;aViLVh]Zg
;aViLVh]Zg
AdX`LVh]Zg
=ZmCji
Figure 8.
-ACHINE"ASE
7ORKBENCH
AV\HXgZl
;aViLVh]Zg
Figure 9.
       


Creating Bends
1. 
       
     
       
Figures 10 11
Figure 10. Lifting clamp cam shaft and die.
Figure 11. Clamp die positions.



 
4. 
Figure 14
2. 

      
Figure 12
Figure 12. Clamping workpiece.
Figure 14. Bending workpiece.
88L
Figure 15. Releasing workpiece.

Steps
1 2
3. 
Figure 13
8L
Figure 13. Tightening bending plate.
5.       
Figure 15
NOTICE
Use the machine only as it is intended to be
used. Adding cheater bars or other meth-
ods of increasing leverage may damage the
machine and will void the warranty.

 
      


To use the work stop and angle stop:
1. 


Figure 16
2.       


Figure 17
Ldg`Hide
Ldg`e^ZXZ
Figure 16. Using work stop.
6c\aZHide
7ZcYZg7VhZ
8L
Figure 17. Using angle stop.
3.       
       


Repetitive Bends

 
Parts Breakdown & List
&
'
(
)
*
+
,
-
.
&'
&(
&)
&)"&
&*
&+
&,
&-
&.
&."&
'%
'%
'&
''
'(
')
')"&
'*
REF PART # DESCRIPTION REF PART # DESCRIPTION
1 PT10050001 BODY 15 PT10050015 WORK STOP
2 PT10050002 CRANK 16 PT10050016 WORK STOP ROD
3 PT10050003 HANDLE 17 PSW03-1 KNOB M10-1.5 x 35
4 PT10050004 STATIONARY JAW 18 PT10050018 PLASTIC GRIP
5 PT10050005 BENDING PLATE 19 PB31M HEX BOLT M10-1.5 X 40
6 PT10050006 BENDING PLATE KNOB 19-1 PW04M FLAT WASHER 10MM
7 PT10050007 BENDING PLATE LEADSCREW 20 PSB14M CAP SCREW M8-1.25 X 20
8 PT10050008 CLAMP DIE 21 PRP08M ROLL PIN 6 X 30
9 PT10050009 CLAMP CAM SHAFT 22 PN09M HEX NUT M12-1.75
12 PT10050012 COVER PLATE 23 PSB64M CAP SCREW M10-1.5 X 25
13 PT10050013 END PLATE 24 PB14M HEX BOLT M10-1.5 X 35
14 PT10050014 ANGLE STOP 24-1 PN02M HEX NUT M10-1.5
14-1 PSN05M SQUARE NUT M12-1.75 25 PT10050025 PIVOT PIN

"UY$IRECTAND3AVEWITH'RIZZLY
®
n4RUSTED0ROVENANDA'REAT6ALUE
/2
s3%#52%/2$%2).'
s/2$%233()00%$7)4().(/523
s%-!),2%30/.3%7)4()./.%(/52
6ISIT/UR7EBSITE4ODAY!ND$ISCOVER
7HY'RIZZLY®)S4HE)NDUSTRY,EADER
#ALL4ODAY&OR!
&2%%
&ULL#OLOR#ATALOG