Grouser Products Ag Pro Silage Special User manual

Date 3-19-2021
PN: 19460-R2
Purchase Date
Serial Number
Model Number
Tractor Model
Dealer
Grouser Products
755 2nd Ave NW - West Fargo, ND 58078
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Website: www.grouser.com
Serial Number: 10206243 & 10206258-Current
Ag Pro Silage Special
Owner’s Manual & Parts Book

2
Description Page
Welcome To The Owner 2
Safety Precautions, Torque Specications & Pre-Installation 3
Decals 4
Maintenance & Lubrication 5
Standard Lift System & Nested Top Arm Lift System 6-7
Tractor Side Hydraulics 8-10
Initial Startup 11
Blade Connection and Disconnection 12
Skid Shoe Adjustment & Tilt Plate Adjustment 13
Ag Pro Silage Special Blade 14-15
Hydraulic Angle-Hydraulic Tilt and Hydraulic Angle-No Tilt System 16-17
Hydraulic Angle-Hydraulic Tilt Hydraulics 18-19
Hydraulic Angle-No Tilt Hydraulics 20-21
No Angle-Hydraulic Tilt System 22-23
No Angle-No Tilt Blade 24
No Angle-No Tilt System 25
Blade Attachments 26-27
Replacement Wear Parts 28
Hydraulic Schematics 29
Hydraulic Multi-Coupler Maintenance 30-31
Contact Us, Improvements, & Warranty 32
Thank you for your recent purchase of a Grouser Ag Pro Silage Special Dozer. Welcome to the family of satised Grouser blade
owners. Grouser Products is committed to offering quality products to help professionals in their daily jobs. We are also committed
to providing you the highest level of customer satisfaction possible. Again, thank you for your patronage. We look forward to
serving you.
This manual contains information concerning the operation, adjustment, safety and maintenance of the Ag Pro Silage Special
Dozer. You have purchased a dependable, long lasting piece of equipment. You can expect to receive long lasting performance
and long service built into our products with proper care and operation. Please have all operators read and understand this manual
carefully. Keep the manual available for reference. If, for any reason, you have questions or comments, we would be happy to hear
from you. Call our toll-free number, 800-747-6182, or send us an e-mail at [email protected]. You can expect us to respond to
your e-mail in a timely manner.
ContentsWelcome to the Owner
HAHT Hydraulic Angle - Hydraulic Tilt
HANT Hydraulic Angle - No Tilt
NAHT No Angle - Hydraulic Tilt
NANT No Angle - No Tilt
Abbreviation Key

3
A careful operator is the best operator. Most accidents can be avoided by observing certain precautions. To help prevent
accidents, read and take the following precautions before operating this equipment. In addition, please follow all safety and
operational instructions of your tractor manufacturer.
The Ag Pro Silage Special Dozer:
1. The Ag Pro Silage Special Dozer should be operated only by those who are responsible and instructed to do so.
2. Read the owner’s manual carefully before using this equipment. Lack of operating knowledge can lead to accidents.
3. Keep the Ag Pro Silage Special Dozer maintained in reliable and satisfactory condition to ensure your safety.
4. Make sure the area is clear of people before moving any equipment.
5. Do not modify or permit anyone else to modify or alter the equipment and its components without rst consulting Grouser
Products.
6. Lower the blade to the ground when not in use.
Servicing the Ag Pro Silage Special Dozer:
1. Read and follow all safety instructions provided by the tractor manufacturer.
2. Always use proper personal safety gear when performing maintenance on equipment.
3. Before servicing, relieve hydraulic pressure, stop engine and fully engage parking brake.
4. Escaping hydraulic uid under pressure can penetrate skin causing serious injury. If uid is injected into skin, obtain medical
attention immediately.
– DO NOT use your hand to check for leaks. Use a piece of cardboard or paper to search for leaks.
– Stop the engine and relieve pressure before connecting or disconnecting lines.
– Tighten all connections before starting the engine or pressurizing lines.
Storing the Ag Pro Silage Special:
1. Thoroughly clean the Ag Pro Silage Special Dozer before storage. Use paint where necessary to prevent rust.
2. Check the Ag Pro Silage Special Dozer for worn or damaged parts. Install new parts as required.
3. Lubricate all pins and joints.
Tighten all bolts to the values listed below unless otherwise noted. Refer to the parts lists for proper length and grade of the bolts.
Torque - Dry (ft–lbs)
SAE Grade 5 SAE Grade 8
Size UNC UNF UNC UNF
5/16 17 19 24 27
3/8 30 35 45 50
7/16 50 55 70 80
1/2 75 85 110 120
9/16 110 120 150 170
5/8 150 170 210 240
3/4 260 300 380 420
7/8 430 470 600 670
1 640 720 910 1020
Torque - Dry (ft-lbs)
Size Grade 10.9
M18 x 2.50 284
M20 x 2.50 401
M22 x 2.50 547
M24 x 3.00 694
Safety Precautions Torque Specications Pre-Installation
Unstrap and remove the lift frame, hoses, top arms, and any boxes of hardware from the undercarriage. If any components are
missing, call Grouser.
Install undercarriage per the tractor specic mounting instructions.

4
Decals
27-9503
PN: 27-9503
PN: 27-2409
WARNING
Cancer and Reproductive Harm
For more information go to
www.P65Warnings.ca.gov
27-40962
STOP
PROPER RATCHET STORAGE
27-40917
Ratchet
Keeper
Ratchet
Handle
Handle
Ratchet Handle Must Be Secured
Between The Ratchet Keeper And
The Handle When Not In Use
FAILURE TO FOLLOW MAY
RESULT IN DAMAGE
Parts May Vary Slightly In Appearance From Your Product
PN: 27-40917
PN: 27-40962
16
AG PRO
PN: 27-40956
PN: 27-14845 PN: 27-14842-XX
XX = Length of Blade
PN: 27-9504
SILAGE SPECIAL
Left and Right Side
Left and Right SideLeft and Right Side

5
Maintenance & Lubrication
Due to the harsh environment this equipment operates in, the following tasks should be performed
every 10 hours or less.
• Inspect all equipment before operation for existing or potential damage.
• Lubricate all joints with high quality grease. See below for grease locations.
• Inspect all bolts, and tighten any loose bolts to torque specications on page 3.
• Check replaceable cutting edge for wear ensuring there is enough material to prevent permanent damage to the Ag Pro Silage
Special Dozer. For cutting edge information, see pages 34 .
• Check hydraulic cylinders and hoses for damage or leaks. For replacement parts, see hydraulic pages 6, 8-9 and 20-29.
• Make sure all non-rotating pins are secured properly.
• Inspect all decals and order replacement decals from your dealer if any are damaged or worn.
• For multi-coupler maintenance, see pages 36-37.
• Inspect all tilt-ways for wear. See page 14 for tilt plate adjustment.
• Replace parts with original parts only.
4X
2 Places
6X
6X
2 Places 4X
2 Places 4X
2 Places 4X
2 Places
6X
2 Places
Top
Center
Pivot
Bottom
Center
Pivot
Left
Angle
Base
Right
Angle
Base
27-41669
PN: 27-41669
4X
2 Places
4X
View From Front of
Angle Frame

6
For JD 9000 and Versatile Wheeled Tractors see Nested Top Arm Lift System
* Quantity May Vary
29
25
5
1
2
24
23
27
3
17
15
22
6
28
29
21
8
12
9
30
19
29
7
28
8
29
20
28
4
13
18
14
16
26*
10
11
Note: The cylinder part number is stamped on the base
end of the cylinder opposite of the hydraulic ports.
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 11-19975-L Top Arm Weld
2 1 11-19975-R Top Arm Weld
3 2 16-20002 1/4" x 3/4 " Hex Bolt Gr 5 NC
4 2 16-20214 3/4" x 1" Hex Bolt Gr 5 NC
5 2 16-20216 3/4" x 1-1/2" Hex Bolt Gr 5 NC
6 4 16-20217 3/4" x 1-3/4" Hex Bolt Gr 5 NC
7 4 16-20220 3/4" x 2-1/2" Hex Bolt Gr 5 NC
8 8 19-13515 Spacer, NR Pin
9 2 19-13525 2.75 x 2.50 x 4.75 Spring Bushing
10 2 19-18089 2.75 x 2.50 x 3.75 Spring Bushing
11 8 19-16695 2.25 x 2.00 x 1.50 Spring Bushing
12 2 26-34745 4.5 x 18 Hydraulic Cylinder
13 1 27-40962 Warning Prop 65 Decal
14 2 27-9503 Pinch Decal (Foot)
15 2 27-9504 Grouser Horizontal Decal
16 1 32-42335 Lift Frame
Cylinder Part No. Description
26-34745 49-12278 Seal Kit 4.5 x 18 Nitrided Rod
ITEM NO. QTY. PART NO. DESCRIPTION
17 1 34-14961 Manual Canister Small
18 2 43-14725 Lift Frame / UC Pin
19 4 43-18120 Top Pin Weld
20 2 43-18127 Top Arm Pin Weld
21 2 43-18175 Lift Cyl Pin Weld
22 2 43-18635 Ag Pro Plus QA Pin
23 1 45-18110-L Male Quick Attach, Ag Pro S
24 1 45-18130-R Male Quick Attach, Ag Pro S
25 2 57-1530 3" OD X .75 ID X .25" HD Flat Washer
26* 6 57-1811 2” Washer
27 2 57-20740 1/4" Flat Washer
28 10 57-20747 3/4" Flat Washer
29 12 58-9369 Straight 1/8" NPT Grease Zerk
30 2 70-20607 3/4" Center Lock Hex Nut Gr 2 NC
Standard Lift System
Some assembly of Lift System components is necessary. Follow the steps listed below. See diagram below for the correct hardware
and orientation of parts.
1. Remove all pins and fasteners on each side of the undercarriage and set aside for later installation.
2. Position the lift frame between the two plates on both sides of the undercarriage and align to the bottom holes.
3. Insert pins and hardware to attach the lift frame, the base end of the lift cylinders, and the top arms to the undercarriage.
4. Insert pins and hardware to attach the male quick attaches to the lift frame, and to the top arms. Use 2” washers as shims to
keep top arm pins tight and in place. Only use as many as needed until pin is tight.
5. Torque all fasteners according to the specications on Page 3.

7
16
11
9
* Quantity May Vary
10
30
26
6
1
2
25
24
3
17
15
20
8
7
30
19
29
12
4
23
22
6
31
30
21
29
5
13
18
28
28 32
27*
30
26
27*
14
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 11-19035-L Nested Top Arm Weld
2 1 11-19035-R Nested Top Arm Weld
3 2 16-20004 1/4" X 1" Hex Bolt Gr 5 NC
4 2 16-20134 1/2" x 3-1/2" Hex Bolt Gr 5 NC
5 2 16-20214 3/4" x 1" Hex Bolt Gr 5 NC
6 4 16-20216 3/4" x 1-1/2" Hex Bolt Gr 5 NC
7 4 16-20217 3/4" x 1-3/4" Hex Bolt Gr 5 NC
8 4 19-13515 Spacer, NR Pin
9 2 19-13525 2.75 x 2.50 x 4.75 Spring Bushing
10 8 19-16695 2.25 x 2.00 x 1.50 Spring Bushing
11 2 19-18089 2.75 x 2.50 x 3.75 Spring Bushing
12 2 26-34753 4.5 x 18 Hydraulic Cylinder With 90° Zerk
13 1 27-40962 Warning Prop 65 Decal
14 2 27-9503 Pinch Decal (Foot)
15 2 27-9504 Grouser Horizontal Decal
16 1 32-42335 Lift Frame
17 1 34-14961 Manual Canister Small
18 2 43-14725 Lift Frame / UC Pin
Note: The cylinder part number is stamped on the base
end of the cylinder opposite of the hydraulic ports.
Cylinder Part No. Description
26-34745 49-12278 Seal Kit 4.5 x 18 Nitrided Rod
ITEM NO. QTY. PART NO. DESCRIPTION
19 2 43-18175 Lift Cyl Pin Weld
20 2 43-18635 Ag Pro Plus QA Pin
21 2 43-19040 Top Arm - Quick Attach Pin Weld
22 2 43-19041 Pin, Lift Cylinder
23 2 43-19043 Top Arm - Undercarriage Pin Weld
24 1 45-18110-L Male Quick Attach, Ag Pro S
25 1 45-18110-R Male Quick Attach, Ag Pro S
26 4 57-1530 3" OD X .75 ID X .25" HD Flat Washer
27* 12 57-1811 2” Washer
28 4 57-20740 1/4" Flat Washer
29 6 57-20747 3/4" Flat Washer
30 10 58-9369 Straight 1/8" NPT Grease Zerk
31 2 70-20604 1/2" Center Lock Hex Nut
32 2 70-20610 1/4" Nyloc Hex Nut Gr 5 NC
Nested Top Arm Lift System

8
Tractor Side Hydraulics
14 2028 21 22 1724
B
5
32
1
33
19
4
16
34
24
25
18
29
13
23
10
26 DETAIL B
See Detail A for correct
hose locations
27
C
A
F
E
H
G
H
G
H
G
8
9
24
30
32
15
24
12
11
26
View of Left Side Hoses
1 Orange Spiral Band
31
From The Front 2 Orange Spiral Bands
27
Lift Hoses (Orange Spiral Bands)
Angle Hoses (Red Spiral Bands)
Tilt Hoses (Green Spiral Bands)
ITEM
NO. PART NO.
HAHT
QTY.
HANT
QTY.
NAHT
QTY.
NANT
QTY. DESCRIPTION
1 16-20124 2 2 2 - 1/2" x 1" Hex Bolt Gr 5 NC
2 16-812525 2 2 2 - 8mm x 1.25mm x 25mm Metric Hex Bolt Gr 10.9
3 18-19995-L 1 1 1 - Multi-Coupler Mount
4 25-19864 1 - - - Multi-Coupling Plate - 4 Port Fixed
5 25-19867 1 - - - Multi-Coupling Plate - 4 Port - Cap
6* 19868 - 1 1 - Multi-Coupling Plate - 2 Port - Fixed
7* 19871 - 1 1 - Multi-Coupling Plate - 2 Port - Cap
8 25-19870 4 2 2 - Multi-Coupling Plate - Male Coupler
9 25-40407 4 2 2 - Multi-Coupling Plate - Snap Ring
10 25-34342 6 4 4 2 Tappet Quick Coupler Male - Poppet Style
11 25-3453 2 - 2 - Pioneer Dust Cap Tilt (Green)
12 25-3455 2 2 - - Pioneer Dust Cap Angle (Red)
13 25-3457 2 2 2 2 Pioneer Dust Cap Lift (Orange)
14 31-11699-10-8 2 2 2 2 JIC Union
15 31-15199-8-8 4 2 2 - JIC Union Elbow 90°
16 31-34030 2 2 2 2 Bulkhead Run Tee JIC
17 31-34040 2 2 2 2 Straight JIC x O-Ring
18A,B 31-34051 6 4 4 2 Straight Thread Elbow 90° JIC x O-Ring
18C 31-6802-08-10 6 4 4 2 Straight Thread Elbow 45° JIC x O-Ring
19 31-34150 4 2 2 - Straight Thread Elbow 45° JIC x O-Ring
20 31-6400-10-08 2 2 2 2 Straight JIC x O-Ring
* Part Not Shown
Hoses Not Drawn to Scale
Item A for CNH, JD 9R, JD 9030
Item B for Versatile, Challenger MT900 and JD 9RX
Item C for Claas Xerion Tractor
Item #1, 3 and 33 not used with Nested Top Arm Lift Systems
HAHT Shown. See Page 10 for remaining Multi-Coupler Configurations.
Every hydraulic function from the front to the back of the system is designated by a and a
letter and can also be referenced on the Hydraulic Schematic on Page 29.
Designated Hose
Locations
ITEM
NO. PART NO. HAHT QTY.
HANT
QTY.
NAHT
QTY.
NANT
QTY. DESCRIPTION
21 34-12932 2 2 2 2 Cylinder Saddle
22 34-16578 2 2 2 2 Hose Clamp (worm drive - 4.5)
23 34-18888-GR 9 - 9 - -12 Green - Spiral Band
24 34-18888-OR 15 15 15 15 -12 Orange - Spiral Band
25 34-18888-RD 9 9 - - -12 Red - Spiral Band
26 35-12633-0535 2 2 2 2 53.5” x 1/2" -8JIC/-8JIC Hose w/ Cordura
27 35-12633-0670 2 2 2 2 67” x 1/2" -8JIC/-8JIC Hose w/Cordura
28 35-18240 2 2 2 2 Lift Cylinder Steel Line
29A,C 35-30183 6 4 4 2 293" (24.42”) x 1/2" -8JIC/-8JIC Hose w/ Cordura
29B 35-18953-3200 6 4 4 2 320" (26.67”) x 1/2" -8JIC/-8JIC Hose w/ Cordura
30 35-31135 2 2 - - 78” x 1/2" -8JIC/-8JIC Hose w/Cordura
31 35-31136 2 - 2 - 81” x 1/2" -8JIC/-8JIC Hose w/Cordura
32 57-20740 2 2 2 - 1/4" Flat Washer
33 57-20744 2 2 2 - 1/2" Washer
34 70-20807 2 2 2 2 3/4" Hex Jam Nut NF
ETilt Rod
Green Spiral Band (X1)
Tilt Base F
Green Spiral Band (X2)
DETAIL A
Right Angle Rod A
Red Spiral Band (X1)
Right Angle Base C
Red Spiral Band (X2)
NOTE: All hoses are marked with colored spiral
bands and should be attached to designated
ports on the Multi-Coupler.
25-19868
25-19871

9
Tractor Side Hydraulics
14 2028 21 22 1724
B
5
32
1
33
19
4
16
34
24
25
18
29
13
23
10
26 DETAIL B
See Detail A for correct
hose locations
27
C
A
F
E
H
G
H
G
H
G
8
9
24
30
32
15
24
12
11
26
View of Left Side Hoses
1 Orange Spiral Band
31
From The Front 2 Orange Spiral Bands
27
Lift Hoses (Orange Spiral Bands)
Angle Hoses (Red Spiral Bands)
Tilt Hoses (Green Spiral Bands)
ITEM
NO. PART NO. HAHT QTY.
HANT
QTY.
NAHT
QTY.
NANT
QTY. DESCRIPTION
1 16-20124 2 2 2 - 1/2" x 1" Hex Bolt Gr 5 NC
2 16-812525 2 2 2 - 8mm x 1.25mm x 25mm Metric Hex Bolt Gr 10.9
3 18-19995-L 1 1 1 - Multi-Coupler Mount
4 25-19864 1 - - - Multi-Coupling Plate - 4 Port Fixed
5 25-19867 1 - - - Multi-Coupling Plate - 4 Port - Cap
6* 19868 - 1 1 - Multi-Coupling Plate - 2 Port - Fixed
7* 19871 - 1 1 - Multi-Coupling Plate - 2 Port - Cap
8 25-19870 4 2 2 - Multi-Coupling Plate - Male Coupler
9 25-40407 4 2 2 - Multi-Coupling Plate - Snap Ring
10 25-34342 6 4 4 2 Tappet Quick Coupler Male - Poppet Style
11 25-3453 2 - 2 - Pioneer Dust Cap Tilt (Green)
12 25-3455 2 2 - - Pioneer Dust Cap Angle (Red)
13 25-3457 2 2 2 2 Pioneer Dust Cap Lift (Orange)
14 31-11699-10-8 2 2 2 2 JIC Union
15 31-15199-8-8 4 2 2 - JIC Union Elbow 90°
16 31-34030 2 2 2 2 Bulkhead Run Tee JIC
17 31-34040 2 2 2 2 Straight JIC x O-Ring
18A,B 31-34051 6 4 4 2 Straight Thread Elbow 90° JIC x O-Ring
18C 31-6802-08-10 6 4 4 2 Straight Thread Elbow 45° JIC x O-Ring
19 31-34150 4 2 2 - Straight Thread Elbow 45° JIC x O-Ring
20 31-6400-10-08 2 2 2 2 Straight JIC x O-Ring
* Part Not Shown
Hoses Not Drawn to Scale
Item A for CNH, JD 9R, JD 9030
Item B for Versatile, Challenger MT900 and JD 9RX
Item C for Claas Xerion Tractor
Item #1, 3 and 33 not used with Nested Top Arm Lift Systems
HAHT Shown. See Page 10 for remaining Multi-Coupler Configurations.
Every hydraulic function from the front to the back of the system is designated by a and a
letter and can also be referenced on the Hydraulic Schematic on Page 29.
Designated Hose
Locations
ITEM
NO. PART NO.
HAHT
QTY.
HANT
QTY.
NAHT
QTY.
NANT
QTY. DESCRIPTION
21 34-12932 2 2 2 2 Cylinder Saddle
22 34-16578 2 2 2 2 Hose Clamp (worm drive - 4.5)
23 34-18888-GR 9 - 9 - -12 Green - Spiral Band
24 34-18888-OR 15 15 15 15 -12 Orange - Spiral Band
25 34-18888-RD 9 9 - - -12 Red - Spiral Band
26 35-12633-0535 2 2 2 2 53.5” x 1/2" -8JIC/-8JIC Hose w/ Cordura
27 35-12633-0670 2 2 2 2 67” x 1/2" -8JIC/-8JIC Hose w/Cordura
28 35-18240 2 2 2 2 Lift Cylinder Steel Line
29A,C 35-30183 6 4 4 2 293" (24.42”) x 1/2" -8JIC/-8JIC Hose w/ Cordura
29B 35-18953-3200 6 4 4 2 320" (26.67”) x 1/2" -8JIC/-8JIC Hose w/ Cordura
30 35-31135 2 2 - - 78” x 1/2" -8JIC/-8JIC Hose w/Cordura
31 35-31136 2 - 2 - 81” x 1/2" -8JIC/-8JIC Hose w/Cordura
32 57-20740 2 2 2 - 1/4" Flat Washer
33 57-20744 2 2 2 - 1/2" Washer
34 70-20807 2 2 2 2 3/4" Hex Jam Nut NF
ETilt Rod
Green Spiral Band (X1)
Tilt Base F
Green Spiral Band (X2)
DETAIL A
Right Angle Rod A
Red Spiral Band (X1)
Right Angle Base C
Red Spiral Band (X2)
NOTE: All hoses are marked with colored spiral
bands and should be attached to designated
ports on the Multi-Coupler.

10
HANT
NAHT
ITEM
NO. PART NO. HANT QTY.
NAHT
QTY. DESCRIPTION
1 16-812525 2 2 8mm x 1.25mm x 25mm Metric Hex Bolt Gr 10.9
2 25-19868 1 1 Multi-Coupling Plate - 2 Port - Fixed
3 25-19871 1 1 Multi-Coupling Plate - 2 Port - Cap
4 57-20740 2 2 1/4" Flat Washer
Red Spiral Band (X1)
3
2
Red Spiral Band (X2)
B
1
Angle Base
Angle Rod A
4
Green Spiral Band (X1)
Tilt Base
2
Green Spiral Band (X2)
F
Tilt Rod E
3
Tractor Side Hydraulics
Note: Refer to Pages 6-9 for the correct hose lengths and hose location.
Note: All connections are identied by spiral bands. 2 bands are from the base end of a cylinder and 1 band is from the
rod end of a cylinder. Orange = Lift, Green = Tilt and Red = Angle.
1. Connect the lift hoses to the lift cylinders.
2. Verify that hoses are not twisted and protected from rubbing on any sharp edges. See Pages 8-10 for proper hose routing.
3. Attach the multi-coupler to the top arm mount and install the 45° ttings.
4. Identify each remaining hose at the front of the undercarriage by the colored bands on end of hose and connect hose to
corresponding 45° tting on multi-coupler. Refer to Pages 8-10 for proper hose locations.
5. Hoses were plugged into the rear of the tractor during the undercarriage installation.
6. Continue on Page 11 for initial startup instructions.

11
Prior to operating the blade system, all air must be purged from the hydraulic system. Follow the steps below for each function on
your blade.
Lift Function:
1. With the lift frame down and blocked, loosen the ttings on both ends of the lift cylinders.
2. Actuate the raise function to supply oil to the rod end of the cylinders.
3. When oil starts to ow from the ttings, stop oil ow, and tighten the tting on the rod end of the lift cylinders.
4. Continue to ow oil until the system is fully raised and then block the lift frame.
5. Actuate the function in the opposite direction to supply oil to the base end of the lift cylinders.
6. When all air is removed from the lift system, stop oil ow and tighten the ttings on the base end of the lift cylinders.
7. Raise lift system and remove blocks. Cycle up and down 5 more times.
8. Check tractor oil level and ll if necessary.
9. Continue with connecting the blade on Page 10.
Tilt Function:
1. Use a lift or jack to tilt the blade system until the left side is fully up, loosen the ttings on the rod and base end of both tilt cylinders.
2. Actuate the tilt function to extend the right tilt cylinder and supply oil to the base end of the right cylinder and to the rod end of the
left cylinder.
3. When oil starts to ow from the ttings, stop oil ow, and tighten the tting on the base end of the right cylinder and rod end of
the left cylinder.
4. Remove the lift or jack.
5. Continue to actuate the tilt function until oil ows out of the remaining open ports.
6. Actuate the tilt function in the opposite direction.
7. When all air is removed from the tilt system, stop oil ow, and tighten the remaining ttings on the cylinders.
8. Cycle both cylinders in and out 5 more times.
9. Check tractor oil level and ll if necessary.
Angle Function:
1. Loosen the ttings on the rod and base end of the left angle cylinder.
2. Actuate the angle function to extend the left angle cylinder and supply oil to the base end of the left cylinder.
3. When oil starts to ow from the ttings, stop oil ow, and tighten the tting on the base end of the left cylinder.
4. Continue to actuate the left angle function in the same direction until the cylinder is fully extended.
5. Actuate the left angle function in the opposite direction.
6. When oil starts to ow from the rod end tting, stop oil ow, and tighten the rod end tting on the left angle cylinder.
7. Continue to actuate the left angle fuction until cylinder is fully retracted.
8. Loosen the ttings on the rod and base end of the right angle cylinder.
9. Actuate the angle function to extend the right angle cylinder and supply oil to the base end of the right cylinder.
10. When oil starts to ow from the ttings, stop oil ow, and tighten the tting on the base end of the right cylinder.
11. Continue to actuate the right angle function in the same direction until the cylinder is fully extended.
12. Actuate the right angle function in the opposite direction.
13. When oil starts to ow from the rod end tting, stop oil ow, and tighten the rod end tting on the right angle cylinder.
14. Continue to actuate the right angle function until cylinder is fully retracted.
16. Cycle the left cylinder in and out 5 more times and then the right cylinder in and out 5 more times.
16. Check tractor oil level and ll if necessary.
Run the blade through all the functions. If any function does not operate correctly, refer to corresponding section above and re-
bleed. If problem still persists, call Grouser Products.
Initial Startup

12
To Connect:
Note: If necessary, use a spotter to help center the blade on the lift system.
1. If necessary, lift the locking latch and push the quick attach lock handle on the left side of the lift system to open the quick
attach system. Refer to Page #15 for further clarication on the quick attach system.
2. Drive the tractor forward slowly until the top edge of the male quick attach is under the top hook of the female quick attach on
the blade assembly.
3. Raise the lift system until the male quick attach engages the female hook. If both sides don’t fully engage, reposition.
Continue to raise the lift system until the blade is off the ground and the female quick attaches are against the front of the male
quick attaches.
4. Shut off the tractor engine and set the parking brake.
5. Pull the quick attach lock handle to engage the quick attach pins and lift the locking latch to lock the handle in place.
6. Clean and connect hydraulic multi-coupler on the top arm. Refer to Pages 20-21 for cleaning and connecting information.
7. If initial startup, refer to Page 9 before operating any function of the blade.
To Disconnect:
1. Lower the blade until the cutting edge is off the ground a few inches.
2. Shut off the tractor engine and set the parking brake.
3. Unhook the multi-coupler on the top arm.
4. Remove the multi-coupler covers from the parking stations on the blade assembly and install on the multi-couplers on the top
arms.
5. Plug the blade side multi-couplers into the parking station.
6. Lift the locking latch and push the quick attach lock handle to disengage the quick attach pins.
7. Start tractor, disengage the parking brake, and lower the blade until cutting edge is on the ground.
8. Continue to slowly lower the lift system to disengage the blade.
9. Slowly back away from the blade. When lift system is clear from the blade, raise the lift system.
10. Shut off the tractor engine and set the parking brake.
Blade Connection and Disconnection

13
Tilt Plate
Figure 1
Tilt Plate Adjustment
Figure 2
Forward/Reverse Lever
Handle
Receiver
Skid Shoe Adjustment:
1. Remove handle from ratchet keeper by pulling hitch clip pin and
insert it into handle receiver on ratchet jack.
2. Loosen locking nut on ratchet jack.
3. Hold body of ratchet jack and rotate ratchet jack handle to raise or
lower skid shoes.
4. If skid shoe is not moving in the proper direction, ip forward/reverse
lever on handle (see Figure 2). Rotate ratchet jack handle again to
move skid shoe in desired direction.
5. After skid shoe is adjusted, rotate ratchet jack handle until it rests
against the ratchet keeper. Return removable handle to ratchet
keeper ensuring that ratchet jack handle is captured by removable
handle and ratchet keeper. Secure handle to ratchet keeper with
hitch clip pin.
6. Tighten locking nut against ratchet jack body to keep it from moving.
7. When skid shoes are worn up to bolt heads, replace skid shoes.
Removable
Handle
Handle
Receiver
Skid Shoe
Preferred Method:
1. The preferred blade position for adjusting tilt plates is laying face down on blocks.
2. Remove 6 bolts from right tilt plates.
3. Add or remove washers as needed to adjust tilt-way clearance to 1/16” - 1/8”.
4. Reinstall bolts in right tilt plates.
5. Follow Steps #2-4 for left tilt plates.
6. Once tilt-way clearance is set, torque bolts to 640 ft-lbs.
Non-Preferred Method:
Note: Do not remove all of the bolts at the same time if the blade is not laying face down.
1. The non-preferred blade position for adjusting tilt plates is
blade in upright position.
2. Remove the 3 bolts from top right tilt plate and bottom
left tilt plate.
3. Add or remove washers as needed to adjust tilt-way
clearance to 1/16” - 1/8”.
4. Reinstall bolts in top right tilt plate and bottom left tilt
plate.
5. Follow Steps #2-4 for bottom right tilt plate and top left tilt
plate.
6. Once tilt-way clearance is set, torque bolts to 640 ft-lbs.
Washers
Skid Shoe Adjustment

14
Ag Pro Silage Special Blade
DWG. NO.: 40910-XX-A
ITEM
NO. PART NO. 12'/QTY. 14'/QTY. 16'/QTY. 18'/QTY. DESCRIPTION
1 15-19250-12 1 - - - Ag Pro SS Blade - 12'
1 15-19250-14 - 1 - - Ag Pro SS Blade - 14'
1 15-19250-16 - - 1 - Ag Pro SS Blade - 16'
1 15-19250-18 - - - 1 Ag Pro SS Blade - 18'
2 16-18945 2 2 2 2 1" x 3" Hex Bolt Gr 5 NC - Short Thread
3 16-20558 3 3 3 3 1" x 2" Hex Bolt Gr 8 NC
4 16-20562 12 12 12 12 1" x 3" Hex Bolt Gr 8 NC
5 16-21064 8 8 8 8 3/8" x 1" Carriage Bolt Gr 5 NC
6 16-21666 4 4 4 4 5/8" x 1-3/4" Plow Bolt Gr 5 NC
7 16-21748 24 28 32 36 3/4" x 2" Plow Bolt Gr 8 NC
8 18-18498-L 1 1 1 1 Ratchet Keeper - Left
9 18-18498-R 1 1 1 1 Ratchet Keeper - Right
10 19-7774 2 2 2 2 1" x 1" Spring Bushing
11 NA 1 1 1 1 Grouser Dozer Metal Serial Tag
ITEM
NO. PART NO. 12'/QTY. 14'/QTY. 16'/QTY. 18'/QTY. DESCRIPTION
12 27-14842-12 1 - - - 12' Decal
12 27-14842-14 - 1 - - 14' Decal
12 27-14842-16 - - 1 - 16' Decal
12 27-14842-18 - - - 1 18' Decal
13 27-14845 1 1 1 1 Ag Pro Blade Decal
14 27-40917 2 2 2 2 Ratchet Holder Storage Decal
15 27-40956 1111Silage Special Decal
16 27-40962 1 1 1 1 Warning Prop 65 Decal
17 29-11118-6 2 - - 3 6' - 3/4”x 8” Cutting Edge
17 29-11118-7 - 2 - - 7' - 3/4”x 8” Cutting Edge
17 29-11118-8 - - 2 - 8' - 3/4”x 8” Cutting Edge
18 34-17565 2 2 2 2 Ratchet Jack
19 34-17567 2222Handle, Ratchet Jack
20 43-18463 2 2 2 2 1” x 2.75” Pin
21 43-18943 2 2 2 2 3/16” x 1-1/2” Cotter Pin
22 43-7767 2222Cylinder Pin Clip
23A 44-15150 1 1 1 1 Ag Pro Dozer Name Plate
23B 44-14830 1 1 1 1 Custom Name Plate
24 44-3749 1 1 1 1 Backdrag Brace Plate
25 50-15458 222212”Round Mushroom Skid Shoe
26 50-17545 2 2 2 2 Mushroom Skid Shoe Mount
27 52-8204 4 4 4 4 Tilt Plate
28 57-20749 12 12 12 12 1" Flat Washer
29 70-20622 8 8 8 8 3/8" Flange Hex Nut Gr 5 NC
30 70-20646 4 4 4 4 5/8" Hex Top Lock Nut Gr 5 NC
31 70-20647 24 28 32 36 3/4" Hex Top Lock Nut Gr 5 NC
32 70-20999 2 2 2 2 1" Hex Top Lock Nut Gr 8 NC
8
6
19
30
32
20
21
25
2
DETAIL A
22
18
26
5
10
Item #A for Ag Pro Dozer Name Plate and #B for Custom Name Plate
24
4
17
28
27
12
7
11
3
13
9
16
15
1
14
23
31
29
A

15
Ag Pro Silage Special Blade
DWG. NO.: 40910-XX-A
ITEM
NO. PART NO. 12'/QTY. 14'/QTY. 16'/QTY. 18'/QTY. DESCRIPTION
1 15-19250-12 1 - - - Ag Pro SS Blade - 12'
1 15-19250-14 - 1 - - Ag Pro SS Blade - 14'
1 15-19250-16 - - 1 - Ag Pro SS Blade - 16'
1 15-19250-18 - - - 1 Ag Pro SS Blade - 18'
2 16-18945 2 2 2 2 1" x 3" Hex Bolt Gr 5 NC - Short Thread
3 16-20558 3 3 3 3 1" x 2" Hex Bolt Gr 8 NC
4 16-20562 12 12 12 12 1" x 3" Hex Bolt Gr 8 NC
5 16-21064 8 8 8 8 3/8" x 1" Carriage Bolt Gr 5 NC
6 16-21666 4 4 4 4 5/8" x 1-3/4" Plow Bolt Gr 5 NC
7 16-21748 24 28 32 36 3/4" x 2" Plow Bolt Gr 8 NC
8 18-18498-L 1 1 1 1 Ratchet Keeper - Left
9 18-18498-R 1 1 1 1 Ratchet Keeper - Right
10 19-7774 2 2 2 2 1" x 1" Spring Bushing
11 NA 1 1 1 1 Grouser Dozer Metal Serial Tag
ITEM
NO. PART NO. 12'/QTY. 14'/QTY. 16'/QTY. 18'/QTY. DESCRIPTION
12 27-14842-12 1 - - - 12' Decal
12 27-14842-14 - 1 - - 14' Decal
12 27-14842-16 - - 1 - 16' Decal
12 27-14842-18 - - - 1 18' Decal
13 27-14845 1 1 1 1 Ag Pro Blade Decal
14 27-40917 2 2 2 2 Ratchet Holder Storage Decal
15 27-40956 1111Silage Special Decal
16 27-40962 1 1 1 1 Warning Prop 65 Decal
17 29-11118-6 2 - - 3 6' - 3/4”x 8” Cutting Edge
17 29-11118-7 - 2 - - 7' - 3/4”x 8” Cutting Edge
17 29-11118-8 - - 2 - 8' - 3/4”x 8” Cutting Edge
18 34-17565 2 2 2 2 Ratchet Jack
19 34-17567 2222Handle, Ratchet Jack
20 43-18463 2 2 2 2 1” x 2.75” Pin
21 43-18943 2 2 2 2 3/16” x 1-1/2” Cotter Pin
22 43-7767 2222Cylinder Pin Clip
23A 44-15150 1 1 1 1 Ag Pro Dozer Name Plate
23B 44-14830 1 1 1 1 Custom Name Plate
24 44-3749 1 1 1 1 Backdrag Brace Plate
25 50-15458 222212”Round Mushroom Skid Shoe
26 50-17545 2 2 2 2 Mushroom Skid Shoe Mount
27 52-8204 4 4 4 4 Tilt Plate
28 57-20749 12 12 12 12 1" Flat Washer
29 70-20622 8 8 8 8 3/8" Flange Hex Nut Gr 5 NC
30 70-20646 4 4 4 4 5/8" Hex Top Lock Nut Gr 5 NC
31 70-20647 24 28 32 36 3/4" Hex Top Lock Nut Gr 5 NC
32 70-20999 2 2 2 2 1" Hex Top Lock Nut Gr 8 NC
8
6
19
30
32
20
21
25
2
DETAIL A
22
18
26
5
10
Item #A for Ag Pro Dozer Name Plate and #B for Custom Name Plate
24
4
17
28
27
12
7
11
3
13
9
16
15
1
14
23
31
29
A

16
Hydraulic Angle-Hydraulic Tilt and Hydraulic Angle-No Tilt System
DWG. NO.: 19893
4
11
17
5
29
9
12
21
25
32
23 20
3
26 7
25
23
20
7
7730 20
26
25
23
20 23 25
33
31
25
18
19
1
2
28 22 24 14 824
6
15
27
16
13
ITEM NO. QTY. PART NO. DESCRIPTION
1 2 11-18495 Blade Stand
2 1 16-20011 1/4" x 2-3/4" Hex Bolt Gr 5 NC
3 2 16-20130 1/2" x 2-1/2" Hex Bolt Gr 5 NC
4 1 16-20560 1" x 2-1/2" Hex Bolt Gr 8 NC
5 2 16-20561 1" x 2-3/4" Hex Bolt Gr 8 NC
6 2 16-21065 3/8" x 1-1/4" Carriage Bolt Gr 5 NC
7 4 16-21126 1/2" x 1-1/2" Carriage Bolt Gr 5 NC
8 2 19-40440 .378” ID x .503” OD x .375” Spacer
9 2 27-2409 Pinch Decal (Hand)
10 2 19-7774 1" x 1" Spring Bushing
11 1 32-17960 Tilt Frame Weld
12 1 32-19130 Angle Frame
13 1 34-17799 Latch Spring
14 1 39-14663 Latch
15 1 39-14665 Handle Weld
16 1 39-3072 Rubber Handle
17 2 43-15712 3/4" x 3-1/4" Pin with Hitch Pin Clip
ITEM NO. QTY. PART NO. DESCRIPTION
18 2 43-18486 Ag Pro SS QA Lock Pin
19 1 43-18491 Angle Pin Weld
20 4 44-8490 Spacer
21 1 57-16928 Plate, Washer
22 2 57-20742 3/8" Flat Washer
23 4 57-20744 1/2" Washer
24 4 57-40408 3/8" Flat Nylon Washer
25 6 70-20604 1/2" Center Lock Hex Nut
26 2 70-20607 3/4" Center Lock Hex Nut Gr 2 NC
27 1 70-20610 1/4" Nyloc Hex Nut Gr 5 NC
28 2 70-20612 3/8" Nyloc Hex Nut Gr 5 NC
29 2 70-20999 1" Hex Top Lock Nut Gr 8 NC
30 1 75-18480 Bell Crank Weld
31 1 75-18485 Link, Right Pin
32 1 75-18526 Link, Handle To Left Pin
33 1 75-18527 Link, Left Pin

17
Hydraulic Angle-Hydraulic Tilt and Hydraulic Angle-No Tilt System
DWG. NO.: 19893
4
11
17
5
29
9
12
21
25
32
23 20
3
26 7
25
23
20
7
7730 20
26
25
23
20 23 25
33
31
25
18
19
1
2
28 22 24 14 824
6
15
27
16
13
ITEM NO. QTY. PART NO. DESCRIPTION
1 2 11-18495 Blade Stand
2 1 16-20011 1/4" x 2-3/4" Hex Bolt Gr 5 NC
3 2 16-20130 1/2" x 2-1/2" Hex Bolt Gr 5 NC
4 1 16-20560 1" x 2-1/2" Hex Bolt Gr 8 NC
5 2 16-20561 1" x 2-3/4" Hex Bolt Gr 8 NC
6 2 16-21065 3/8" x 1-1/4" Carriage Bolt Gr 5 NC
7 4 16-21126 1/2" x 1-1/2" Carriage Bolt Gr 5 NC
8 2 19-40440 .378” ID x .503” OD x .375” Spacer
9 2 27-2409 Pinch Decal (Hand)
10 2 19-7774 1" x 1" Spring Bushing
11 1 32-17960 Tilt Frame Weld
12 1 32-19130 Angle Frame
13 1 34-17799 Latch Spring
14 1 39-14663 Latch
15 1 39-14665 Handle Weld
16 1 39-3072 Rubber Handle
17 2 43-15712 3/4" x 3-1/4" Pin with Hitch Pin Clip
ITEM NO. QTY. PART NO. DESCRIPTION
18 2 43-18486 Ag Pro SS QA Lock Pin
19 1 43-18491 Angle Pin Weld
20 4 44-8490 Spacer
21 1 57-16928 Plate, Washer
22 2 57-20742 3/8" Flat Washer
23 4 57-20744 1/2" Washer
24 4 57-40408 3/8" Flat Nylon Washer
25 6 70-20604 1/2" Center Lock Hex Nut
26 2 70-20607 3/4" Center Lock Hex Nut Gr 2 NC
27 1 70-20610 1/4" Nyloc Hex Nut Gr 5 NC
28 2 70-20612 3/8" Nyloc Hex Nut Gr 5 NC
29 2 70-20999 1" Hex Top Lock Nut Gr 8 NC
30 1 75-18480 Bell Crank Weld
31 1 75-18485 Link, Right Pin
32 1 75-18526 Link, Handle To Left Pin
33 1 75-18527 Link, Left Pin

18
DWG. NO.: 19893
Cylinder Part No. Description
26-34747 49-12271 Seal Kit 4x8 Nitrided Rod, Clevis Ends
26-34750 49-12275 Seal Kit 5 x 20 Nitrided Rod
ITEM NO. QTY. PART NO. DESCRIPTION
1 3 16-20038 5/16" x 2" Hex Bolt Gr 5 NC
2 2 16-20040 5/16" x 2-1/2" Hex Bolt Gr 5 NC
3 2 16-20134 1/2" x 3-1/2" Hex Bolt Gr 5 NC
4 2 16-20219 3/4" x 2-1/4" Hex Bolt Gr 5 NC
5 4 16-35C612 3/8" x 3/4" Flange Bolt
6 3 18-19311-03-P-087 Hose Clamp
7 1 18-19311-03-P-100 Hose Clamp
8 3 18-19312-03 Twin Cover Plate
9 1 18-19313-04 Twin Stacking Bolt
10 1 18-19314-02 Twin Safety Plate
11 2 19-13515 Spacer, NR Pin
12 4 19-13577 NR Pin Spacer Clevis End
13 8 19-16695 2.25" x 2.00" x 1.50" Spring Bushing
14 4 25-19865 Multi-Coupling - Female Coupler
15 1 25-19866 Multi-Coupling Plate - 4 Port Mobile
16 4 25-40407 Multi-Coupling - Snap Ring
17 2 26-34747 4 x 8 Cylinder w/ Clevis Ends
18 2 26-34750 5 x 20 Cylinder Bushed Tube Ends
19 6 31-11492-8-8 Male JIC x Female JIC Swivel Nut Elbow 45°
20 2 31-11699-10-8 JIC Union
21 2 31-34030 Bulkhead Run Tee JIC
22 6 31-34040 Straight JIC x O-Ring
23 2 31-34041 Straight JIC x O-Ring
24 2 31-34042 Straight JIC x O-Ring
25 4 31-34050 Straight Thread Elbow 90° JIC x O-Ring
26 2 31-34060 Branch Tee JIC x O-Ring
ITEM NO. QTY. PART NO. DESCRIPTION
27 2 31-13933-2-2 1/8” NPT Street Elbow
28 2 34-12932 Cylinder Saddle
29 2 34-12933 Hose Clamp (worm drive - 5.0)
30 18 34-18888-RD -12 Red - Spiral Band
31 18 34-18888-GR -12 Green - Spiral Band
32 1 34-19217 Rubber Seal
33 2 35-12931 Formed Steel Line
34 2 35-19355 75.5" x 1/2" -8JIC/-8JIC Hose (w/ 1 Collar & Cordura)
35 1 35-19356 122" x 3/8" -8JIC/-8JIC Hose (w/ 3 Collar & Cordura)
36 1 35-19359 128.5" x 3/8" -8JIC/-8JIC Hose (w/3 Collar & Cordura)
37 2 35-30018 33" x 3/8" -8JIC/-8JIC Hose
38 2 35-30081 37" x 3/8" -8JIC/-8JIC Hose
39 4 35-31113 28" x 1/2" -8 JIC/-8 JIC Hose w/ Cordura
40 4 43-13580 Pin Weld
41 2 43-18487 Angle Cylinder Base Pin
42 2 43-18490 Angle Cylinder Rod Pin Weld
43 1 44-19218 Seal Clamp Plate
44 1 44-19219 Cover Plate
45 1 56-7772 Valve
46 4 57-20744 1/2" Washer
47 2 57-20747 3/4" Flat Washer
48 2 58-9369 Straight 1/8" NPT Grease Zerk
49 2 58-18994-0440 44" Grease Hose (w/lock nut and grease zerk)
50 2 58-18994-0570 57" Grease Hose (w/lock nut and grease zerk)
51 2 70-20581 5/16" Hex Nut Gr 5 NC
52 6 70-20604 1/2" Center Lock Hex Nut
53 2 70-20607 3/4" Center Lock Hex Nut Gr 2 NC
54 2 70-20807 3/4" Hex Jam Nut NF
Note: Every hydraulic function from the front to the back of the system is
designated by a letter and can also be referenced on the Hydraulic Schematic.
D
Green Spiral Band X2
Right Angle Base
25
2
45
19
26
19
Left Angle Rod Red Spiral Band X2
D
51
Left Angle Base B
Green Spiral Band X1
Right Angle Rod B
Red Spiral Band X1
25
22
17
40
12 5
44
37
38
37
38
35
36
39
39
34
34
52
53
1
31
31
31
Red Spiral Band X2
C
F
31
13
Red Spiral Band X1
Right Angle Rod A
Right Angle Base
E
48
16
15
14
24
33
23 20 29 28
18
4
47
11
42
41
3
22
19
21
54
49
27
50
50
49
Grease Lines
43
32
46
52
7910 68 1
FC
30
31
Note: The cylinder part number is stamped on the base
end of the cylinder opposite of the hydraulic ports.
E
A
Green Spiral Band X2
F
Right Angle Rod
Left Tilt Base
All hoses are marked with colored spiral bands and should
Red Spiral Band X1
A
be attached to designated ports on the Multi-Coupler.
Note: View is from Multi-Coupler Installed on Top Arm.
Left Tilt Rod E
Green Spiral Band X1
Right Angle Base C
Red Spiral Band X2
Hydraulic Angle-Hydraulic Tilt Hydraulics

19
DWG. NO.: 19893
Cylinder Part No. Description
26-34747 49-12271 Seal Kit 4x8 Nitrided Rod, Clevis Ends
26-34750 49-12275 Seal Kit 5 x 20 Nitrided Rod
ITEM NO. QTY. PART NO. DESCRIPTION
1 3 16-20038 5/16" x 2" Hex Bolt Gr 5 NC
2 2 16-20040 5/16" x 2-1/2" Hex Bolt Gr 5 NC
3 2 16-20134 1/2" x 3-1/2" Hex Bolt Gr 5 NC
4 2 16-20219 3/4" x 2-1/4" Hex Bolt Gr 5 NC
5 4 16-35C612 3/8" x 3/4" Flange Bolt
6 3 18-19311-03-P-087 Hose Clamp
7 1 18-19311-03-P-100 Hose Clamp
8 3 18-19312-03 Twin Cover Plate
9 1 18-19313-04 Twin Stacking Bolt
10 1 18-19314-02 Twin Safety Plate
11 2 19-13515 Spacer, NR Pin
12 4 19-13577 NR Pin Spacer Clevis End
13 8 19-16695 2.25" x 2.00" x 1.50" Spring Bushing
14 4 25-19865 Multi-Coupling - Female Coupler
15 1 25-19866 Multi-Coupling Plate - 4 Port Mobile
16 4 25-40407 Multi-Coupling - Snap Ring
17 2 26-34747 4 x 8 Cylinder w/ Clevis Ends
18 2 26-34750 5 x 20 Cylinder Bushed Tube Ends
19 6 31-11492-8-8 Male JIC x Female JIC Swivel Nut Elbow 45°
20 2 31-11699-10-8 JIC Union
21 2 31-34030 Bulkhead Run Tee JIC
22 6 31-34040 Straight JIC x O-Ring
23 2 31-34041 Straight JIC x O-Ring
24 2 31-34042 Straight JIC x O-Ring
25 4 31-34050 Straight Thread Elbow 90° JIC x O-Ring
26 2 31-34060 Branch Tee JIC x O-Ring
ITEM NO. QTY. PART NO. DESCRIPTION
27 2 31-13933-2-2 1/8” NPT Street Elbow
28 2 34-12932 Cylinder Saddle
29 2 34-12933 Hose Clamp (worm drive - 5.0)
30 18 34-18888-RD -12 Red - Spiral Band
31 18 34-18888-GR -12 Green - Spiral Band
32 1 34-19217 Rubber Seal
33 2 35-12931 Formed Steel Line
34 2 35-19355 75.5" x 1/2" -8JIC/-8JIC Hose (w/ 1 Collar & Cordura)
35 1 35-19356 122" x 3/8" -8JIC/-8JIC Hose (w/ 3 Collar & Cordura)
36 1 35-19359 128.5" x 3/8" -8JIC/-8JIC Hose (w/3 Collar & Cordura)
37 2 35-30018 33" x 3/8" -8JIC/-8JIC Hose
38 2 35-30081 37" x 3/8" -8JIC/-8JIC Hose
39 4 35-31113 28" x 1/2" -8 JIC/-8 JIC Hose w/ Cordura
40 4 43-13580 Pin Weld
41 2 43-18487 Angle Cylinder Base Pin
42 2 43-18490 Angle Cylinder Rod Pin Weld
43 1 44-19218 Seal Clamp Plate
44 1 44-19219 Cover Plate
45 1 56-7772 Valve
46 4 57-20744 1/2" Washer
47 2 57-20747 3/4" Flat Washer
48 2 58-9369 Straight 1/8" NPT Grease Zerk
49 2 58-18994-0440 44" Grease Hose (w/lock nut and grease zerk)
50 2 58-18994-0570 57" Grease Hose (w/lock nut and grease zerk)
51 2 70-20581 5/16" Hex Nut Gr 5 NC
52 6 70-20604 1/2" Center Lock Hex Nut
53 2 70-20607 3/4" Center Lock Hex Nut Gr 2 NC
54 2 70-20807 3/4" Hex Jam Nut NF
Note: Every hydraulic function from the front to the back of the system is
designated by a letter and can also be referenced on the Hydraulic Schematic.
D
Green Spiral Band X2
Right Angle Base
25
2
45
19
26
19
Left Angle Rod Red Spiral Band X2
D
51
Left Angle Base B
Green Spiral Band X1
Right Angle Rod B
Red Spiral Band X1
25
22
17
40
12 5
44
37
38
37
38
35
36
39
39
34
34
52
53
1
31
31
31
Red Spiral Band X2
C
F
31
13
Red Spiral Band X1
Right Angle Rod A
Right Angle Base
E
48
16
15
14
24
33
23 20 29 28
18
4
47
11
42
41
3
22
19
21
54
49
27
50
50
49
Grease Lines
43
32
46
52
7910 68 1
FC
30
31
Note: The cylinder part number is stamped on the base
end of the cylinder opposite of the hydraulic ports.
EA
Green Spiral Band X2
F
Right Angle Rod
Left Tilt Base
All hoses are marked with colored spiral bands and should
Red Spiral Band X1
A
be attached to designated ports on the Multi-Coupler.
Note: View is from Multi-Coupler Installed on Top Arm.
Left Tilt Rod E
Green Spiral Band X1
Right Angle Base C
Red Spiral Band X2
Hydraulic Angle-Hydraulic Tilt Hydraulics

20
DWG. NO.: 19892
29
5
1
37
29
10
33
28 28
39
41
36
Red Spiral Band X1
A
40
11
Right Angle Rod
Red Spiral Band X2
31
9
37
Right Angle Base C
6
Right Angle Base
21
3
34
16
22
16
38
D
Red Spiral Band X2
Green Spiral Band X1
B
Left Angle Base
Green Spiral Band X2
D
Left Angle Rod
Right Angle Rod B
Red Spiral Band X1
Cylinder Part No. Description
26-34750 49-12275 Seal Kit 5 x 20 Nitrided Rod
ITEM NO. QTY. PART NO. DESCRIPTION
1 1 14-9366 Ag Pro Non Tilt Bar
2 1 16-20038 5/16" x 2" Hex Bolt Gr 5 NC
3 2 16-20040 5/16" x 2-1/2" Hex Bolt Gr 5 NC
4 2 16-20134 1/2" x 3-1/2" Hex Bolt Gr 5 NC
5 2 16-20219 3/4" x 2-1/4" Hex Bolt Gr 5 NC
6 2 16-20564 1" x 3-1/2" Hex Bolt Gr.8 NC
7 1 18-19311-03-P-100 Hose Clamp
8 1 18-19312-03 Twin Cover Plate
9 2 19-13515 Spacer, NR Pin
10 1 19-7774 1" x 1" Spring Bushing
11 8 19-16695 2.25" x 2.00" x 1.50" Spring Bushing
12 2 26-34750 5 x 20 Cylinder Bushed Tube Ends
13 4 25-19865 Multi-Coupling - Female Coupler
14 1 25-19869 Multi-Coupling Plate - 2 Port - Mobile
15 4 25-40407 Multi-Coupling - Snap Ring
16 4 31-11492-8-8 Male JIC x Female JIC Swivel Nut Elbow 45°
17 2 31-11699-10-8 JIC Union
18 2 31-34040 Straight JIC x O-Ring
19 2 31-34041 Straight JIC x O-Ring
20 2 31-34042 Straight JIC x O-Ring
21 2 31-34050 Straight Thread Elbow 90° JIC x O-Ring
22 2 31-34060 Branch Tee JIC x O-Ring
23 2 34-12932 Cylinder Saddle
24 2 34-12933 Hose Clamp (worm drive - 5.0)
25 18 34-18888-RD -12 Red - Spiral Band
26 1 34-19217 Rubber Seal
27 2 35-12931 Formed Steel Line
28 2 35-19355 75.5" x 1/2" -8JIC/-8JIC Hose (w/ 1 Collar & Cordura)
29 4 35-31113 28" x 1/2" -8 JIC/-8 JIC Hose w/ Cordura
Note: Every hydraulic function from the front to the back of the system is
designated by a letter and can also be referenced on the Hydraulic Schematic.
ITEM NO. QTY. PART NO. DESCRIPTION
30 2 43-18487 Angle Cylinder Base Pin
31 2 43-18490 Angle Cylinder Rod Pin Weld
32 1 44-19218 Seal Clamp Plate
33 1 44-19219 Cover Plate
34 1 56-7772 Valve
35 4 57-20744 1/2" Washer
36 2 57-20747 3/4" Flat Washer
37 4 57-20749 1" Flat Washer
38 2 70-20581 5/16" Hex Nut Gr 5 NC
39 6 70-20604 1/2" Center Lock Hex Nut
40 2 70-20607 3/4" Center Lock Hex Nut Gr 2 NC
41 2 70-20609 1" Hex Center Lock Nut Gr.2 NC
17
12 19
27
23
24
30
204
Red Spiral Band X1
be attached to designated ports on the Multi-Coupler.
View is from Multi-Coupler Installed on Top Arm.Note:
Right Angle Rod A
All hoses are marked with colored spiral bands and should
Right Angle Base C
Red Spiral Band X2
14
15
32
35
87
25
39
26
13
2
Note: The cylinder part number is stamped on the base
end of the cylinder opposite of the hydraulic ports.
18
C
A
Hydraulic Angle-No Tilt Hydraulics