GROWRILLA 2.0 PRO User manual

MANUAL INSTRUCTION
[phone] www.growrillahydroponics.com
[e-mail]
Strada Comunale da Bertolla
all’Abbadia di Stura, 140
10156 Torino - ITALY
2.0PRO
2.0PRO
new

Growrilla is a 100% Italian brand of hydroponic farming systems, designed
and made in Italy by growers for growers.
The project stems from a passion for indoor gardening and a common need
for all growers: getting the most out of their plants .
The constant search for information and the desire to experiment with new
techniques has led us to hydroponics, an alternative cultivation method to
the land. Fascinated by the results obtained from the great potential oe-
red, we decided to propose our own system, the result of direct experience
gained over the years, with the aim of oering the grower a functional, easy
to use and high performance product.
Growrilla is not simply a system, first of all it wants to be a resource capable
of providing the grower with the tools necessary to get the most, because
we know that a fast car is not enough to win a race, it is the pilot that makes
the dierence!
Growing with a Growrilla system also means relying on technical and edu-
cational support which, through video tutorials, articles and texts that are
constantly updated, will give you all the information you need to achieve
the results you are looking for!
WELCOME
ABOUT US
This instruction manual is divided into 5 step, in order to help you for a
right assembly of the system. By closely following these instructions you
will ensure your system is properly installed and ready to grow!
STEP 1. SYSTEM SET UP
STEP 2. CONTROLLER POT FITTING KIT
STEP 3. AIR DISTRIBUTION SYSTEM
STEP 4. TESTING
STEP 5. SYSTEM UPGRADE
INSTRUCTION MANUAL STEPS
1

“Hello and congratulations for choosing
a Grorilla RDWc system. I’m your guide who
will help you to assembly and set up your
RDWc system. Please read carefully this
manual instruction, take your time and try to
work in a neat and clean mode, this will ensure
to avoid any issues and make a good job!”
INDEX
36
41
32
21
16
09
05
UPGRADE
RESET / SYSTEM CLEANING
42
LOGIC OF RDWC SYSTEMS
SYSTEM TESTING
AIR DISTRIBUTION
CONTROLLER POT FITTING
ASSEMBLY AND SET UP
SYESTEM COMPONENTS
2

SIMBOLS
The presence of this symbol indicates to pay the attention to the subject
matter.
Lubricate.
Risk of leakage , pay attention to this step.
Ceck that everything has been done right.
Rotate and screw.
Scan this QRcode to download the manual
directly on your electronic device.
3

Questo manuale contiene informazioni molto importanti. Leggere attenta-
mente queste istruzioni prima di iniziare e conservarle per ogni eventualità
futura.
- GROWRILLA declina qualsiasi responsabilità per utilizzo improprio del
prodotto, o per un uso non descritto in questo manuale.
- Prima di utilizzare il prodotto per la prima volta, rimuovere
tutto l’imballaggio e assicurarsi che il prodotto sia in
perfette condizioni. Se così non è, non utilizzare il prodotto
e contattare GROWRILLA dal momento che la garanzia copre
qualsiasi danno di origine o difetto di fabbrica.
- Prima di collegare l’apparecchio alla rete elettrica,
assicurarsi che il cavo e la spina siano in perfette condizioni.
- Questo apparecchio è inteso esclusivamente per uso domestico. Non
esporre il prodotto a condizioni climatiche avverse come pioggia, neve, sole,
ecc.
- Non tirare mai dal cavo per scollegore l’apparecchio, tirare sempre dalla
spina dopo essersi assicurati che l’apparecchio sia spento.
-Per la sicurezza dell’utente e per un corretto funzionamento
del dispositivo, usare sempre ricambi e accessori GROWRILLA.
READ ME
IMBALLAGGIO
I materiali di imballaggio dell’apparecchio sono integrati in
un sistema di raccolta, classificazione e riciclaggio dei rifiuti.
Si prega di smaltirli negli appositi contenitori pubblici.
PRODOTTO ELETTRICO/ELETTRONICO
Questo simbolo indica che, una volta teminato il ciclo di vita
del prodotto, se si desidera smaltirlo, non deve essere trattato
come rifiuto domestico ma deve essere consegnato presso
l’idoneo punto di raccolta per il riciclaggio di apparecchiature
elettriche e elettroniche (RAEE). Questo prodotto non
contiente concentrazioni di sostanze che potrebbero causare
eetti negativi per l’ambiente.
AVVERTENZE DI SICUREZZA
RICICLAGGIO / SMALTIMENTO
4

AREA 1 - SYETEM COMPONENTS
SI-GRC50VDC19
CONTROLLER
POT PRO 2.0
SI-GRC50VPAS19
IN LINE POT
PRO 2.0
SI-GRCOP19
CONTROLLER LID
SI-GRCCOP191F
DWC POT LIDS
ID-NETHD014
NET POT 14CM
RC-GSKGGDN50
WATER PROOF 50mm
RUBBER GASKETS
RC-PPBG90502B
ELBOW 90 PP
PUSH FIT D50
RC-PPBT90502B
TEE PP PUSH
FIT D50
COMPONENT
SYSTEM
TU-PVC50010
TU-PVC50015
TU-PVC50030
TU-PVC50040
PVC PIPE DN50
L 10 15 30 40
SI-GRC50TR40D
RETURN TEE D50
L 40 X 1"
RC-VALPVCDMF
VALVE 1"
MALE FEMALE
RC-GSKORDM
O RING 1" 1/4
RC-VALDMF
COMPACT VALVE 1"
MALE FEMALE
IR-FLTD50B
IN LINE FILTER 1"
TU-PVCGFP25
RETURN HOSE
20MM
--
---
5

AREA 2 - CONTROLLER POT COMPONENTS
RACCORDI INGRESSO / USCITA SISTEMA - CHILLER IN/OUT
RC-FILPRLCMM
EXT. TRHEADED
FITTING 3/4" MALE
RC-FIL90CCFFGM
THREADED ELBOW
90 3/4" FF
SI-GRC90CGMV
VENTURI ELBOW
RC-PG90CGM
ELBOW BARBED
FITTING 16X3/4” FEM
RC-ATSPC
BULKHEAD 3/4"
ID-PAC135TB
WATER PUMP
EDEN 135TB
RC-PG20DGM
BARBED FITTING
1" 20X1" F
RC-PG20CGM
BARBED FITTING
20X3/4" F
RC-PG20CM
BARBED FITTING
20X3/4" M
RC-PG16CM
BARBED FITTING
MALE 16 X ¾”
RC-FILTECCFFFGM
THREADED TEE
3/4" FFF
6

AREA 3 - AIR DISTRIBUTION SYSTEM
T
AIR HOSE
6X4MM
TU-PVCTH0812
AIR HOSE
12X8MM
PVC AIR HOSE
6X4MM L30CM
PVC64030 RC-GSKPT1006
AIR GASKETS
6MM
RC-PG900305
AIR ELBOW FITTING
3X5MM
RC-PGMU1206U1
AIRMANIFOLD 12X6
1 WAY OUT
RC-PGMU1206U2
AIRMANIFOLD 12X6
2 WAY OUT
RC-PGSMU1206U4
AIRMANIFOLD 12X6
4 WAY OUT
COMPONENT
SYSTEM
RC-PGSTAP012
END CAP 12MM
ID-POR1002020B
AIR STONE
TU-PEN12050B
TU-PEN12060B
TU-PEN1205100B
AIR DISTRIBUTION
PIPE 12 X9MM
RC-PG9010
PORTAGOMMA
A GOMITO 10MM
ID-PARV30
AIR PUMP HAILEA
V SERIES

ID-PARET30
ID-PARET40
ID-PARET80
ID-PARET100
AIR PUMP
ET SERIES
SI-GRC50GCA3F
AIR JOINT
3/4 ROWS
SI-GRC50GCA4F
L60/100
TU-SIL0604100
ID-PARV60
7

AREA 4 - ADDITIONAL COMPONENTS
ID-VALG12178
FLOAT VALVE
ID-CONTF098
ID-CONTF157
ID-CONTF225
ID-CONTF500
ID-CONTF700
FLEXIBLE STORAGE
TANK
SI-GRCTF16MT2
CONNECTION
QUICK FITTING
SI-GRC50MMBPR
EXTENSION FOR
DELIVERY MANIFOLD B
SI-GRC50MMAPR
EXTENSION FOR
DELIVERY MANIFOLD A
TU-PVCGFP16
TUBO FLESSIBILE
PVC DN16
ID-PACCHJ600
ID-PACCHJ800
ID-PACCHJ1500
CHILLER KIT
WATER PUMP
8

INSTALLATION
SYESTEM
STEP 1 SYSTEM INSTALLATION
RC-GSKGGDN50
a) Unbox. Place all parts adjacent to the grow area and keep
all the components separately. All the components are divided
by type, this will make it easy to recognize them and will help you
to understand where they have to be used.
b) Gaskets. Insert the water proof gaskets 50mm inside the
hole at the bottom of the buckets, making sure to put them with
the FRONT writing on the outside of the pots.
LUBRICATE. use a bit
of soap or other lubricant
will help you to insert the
gaskets inside the holes
c) put all the pots on the floor of your grow area , lo-
oking at the shape of your system ( 2, 3 or 4 rows)
and with the air hole in the same position as shown
in the picture below.
air hole
rubber hole
9

e) Delivery and return manifold. The
return and delivery manifolds are made with PVC
pipe and PUSH FIT FITTING, they are easy to
assemble and disassemble. Refer to the shape of
your system to assemble the manifolds, as
shown below.
Fat Fitting. they are easy to
assemble and disassemble. Refer
to the shape of your system to
assemble the manifolds, as
shown below.
How to fit the pipe.
insert the pipe inside the
gasket simply sliding it
inside them.
Gasket. lubricate the
internal side of the gaskets
and the PVC pipe before
insert them
d) now you are able to start to insert the connection pipes inside
the gaskets.
2 FILE 3 FILE 4 FILE
air hole
10

MANIFOLD ASSEMBLY
DELIVERY
2 ROWS 3 ROWS
4 ROWS
SI-GRCMRB50
SI-GRCMRB50
SI-GRCMRB50
SI-GRCMRB50
SI-GRCMRB50 SI-GRCMRB50
11

f) Assembly diagrams DELIVERY MANIFOLD.
SI-GRC50MMA DELIVERY MANIFOLD A
2/3 ROWS
DELIVERY MANIFOLD B
3/4 ROWS
RETURN MANIFOLD A
2/4 ROWS
SI-GRC50MMB
L15
L15
L15
L10 L10
L15
L15
L40
L40
RC-PPBG90502B x1
x2
TU-PVC50015
TU-PVC50040 x1
x3
x1
RC-PPBG90502B
x1
RC-PPBT90502B
TU-PVC50015
SI-GRC50MRA
SI-GRC50TR40D x2
x3
x1
RC-PPBT90502B
x2
RC-PPBG90502B
TU-PVC50015
RETURN MANIFOLD B
3 ROWS
L10 L10
L10
L40 L40
SI-GRC50MRB
SI-GRCTR5040D x2
x3
x1
RC-PPBT90502B
x2
RC-PPBG90502B
TU-PVC50015
12

SYSTEM
ROWS RDWC
2
SI-GRC50MMA
SI-GRC50MMA
DISTANCE
BETWEEN POTS:
the distance between
pots can be adjusted
simply sliding the pipes
inside the pots ( please
keep minimum 3 cm of
pipe inside the the pot)
g) DELIVERY MANIFOLD FOR 2/ ROWS SYSTEM. connect the
controller pot to the first two growing pot.
h) Growing Pot Connection .
i) RETURN MANIFOLD FOR 2 ROWS SYSTEM. connect the last
two pots at the back of the system with the relative RETURN MA-
NIFOLD
TU-PVC50030
SI-GRC50MRA
13

SI-GRC50MMA
SI-GRC50MMB
SYSTEM
ROWS RDWC
3
l) DELIVERY MANIFOLD FOR 3/ ROWS SYSTEM: connect the
controller pot to the first 3 growing pots . Use the component
SI-GRC50MMB to connect the growing pot 1 and 2. Use the com-
ponent SI-GRC50MMA to connect the growing pot 3.
m) Growing Pot Connection .
n) RETURN MANIFOLD FOR 3 ROWS SYSTEM. connect the last
three pots at the back of the system with the relative RETURN
MANIFOLD ( SI-GRC50MRB)
TU-PVC50030
SI-GRC50MRB
DISTANCE
BETWEEN POTS:
the distance between
pots can be adjusted
simply sliding the pipes
inside the pots ( please
keep minimum 3 cm of
pipe inside the the pot)
14

SI-GRC50MMB SI-GRC50MMB
o) DELIVERY MANIFOLD FOR 4/ ROWS SYSTEM. connect the
controller pot to the first 4 growing pots . Use the two componen-
ts SI-GRC50MMB to connect the growing pot 1 and 2, then con-
nect the pots 3 and 4
p) Growing Pot Connection .
q) RETURN MANIFOLD FOR 4 ROWS SYSTEM. connect the last
four pots at the back of the system with the two relative RETURN
MANIFOLD ( SI-GRC50MRa)
TU-PVC50030
SI-GRC50MRASI-GRC50MRA
15
SYSTEM
ROWS RDWC
4
DISTANCE
BETWEEN POTS:
the distance between
pots can be adjusted
simply sliding the pipes
inside the pots ( please
keep minimum 3 cm of
pipe inside the the pot)

POT FITTING KIT
CONTROLLER
RC-FIL90CCFFGM
ID-PAC135TB
STEP 3 CONTROLLER POT FITTING KIT
a) Unbox. Keep the controller pot fitting bag and start the
assembly.
b) Water Pump. Screw the extension tube and the elbow
threaded fitting as shown in the figure.
c) BULKHEAD. Put the bulkhead inside the
hole of the controller pot, keeping the gasket
inside it.
16

RC-FILPRLCMM
Note. Make it sure that all
the fitting are well screwed.
Water Pump. Make sure
the water pump is perfectly
set on the ground.
SI-GRC90CGMV
POT FITTING KIT
CONTROLLER
d) Screw the VENTURI ELBOW and the other EXTENSION TUBE
to the internal side of the controller pot.
e) Venturi Elbow. this component is designed for mixing the
water from the pump with the air in order to keep the water
inside the controller pot well oxygenated. Once the system is
filled with water, operate the pump and adjust the VENTURI air
tube until the Venturi eect is triggered. If everything is done
correctly you will see bubbles appear in the control pot
Venturi. Connect the venturi
elbow inside the control pot.
17

KIT FILTRO CON VALVOLA 1"
SI-GRC50FVDK
RC-VALPVCDMF x1
x1
x1
IR-FLTD50B
x1
RC-VALDMF
RC-GSKORDM
ORING. remember
to put the o'ring on
the male thread of the
valve.
2 ROWS
f) Screw the FILTER + VALVE KIT inside the RETURN TEE then connect the
water sucking hose to the second valve. Make sure that the two valves are tight-
ly screwed.
HOSE KIT
RETURN
RETURN HOSE. length is
variable according to the
number of pots envolved.
18

Aspirazione.
La lunghezza di
questo compo-
nete varia in base
al numero di vasi
posati.
3 FILE
g) Nel sistema a 3 FILE i due tubi di aspirazione dei moduli di Ritorno rimango-
no i medesimi, a variare di lunghezza sarà la dorsale principale che va dal Tee al
vaso di controllo.
HOSE KIT
RETURN
SI-GRC50GR3F
SI-GRC50GR3F
19