GSi PNEG-2286 User manual

®
Metric Aeration Transition
Installation Manual
PNEG-2286
Version 1.0
Date: 11-07-19
PNEG-2286

All information, illustrations, photos, and specifications in this manual are based on the latest
information available at the time of publication. The right is reserved to make changes at any
time without notice.
2PNEG-2286 Metric Aeration Transition

Contents
Chapter 1 Safety Precautions ....................................................................................................................5
Safety Guidelines........................................................................................................................5
Safety Decals .............................................................................................................................9
Safety Sign-off Sheet.................................................................................................................10
Chapter 2 Aeration Transition Instructions.............................................................................................. 11
Parts List .................................................................................................................................. 11
Installation ................................................................................................................................14
Limited Warranty — EME Grain Products ................................................................................23
PNEG-2286 Metric Aeration Transition 3

NOTES
4PNEG-2286 Metric Aeration Transition

1Safety Precautions
Topics Covered in this Chapter
▪ Safety Guidelines
▪ Safety Decals
▪ Safety Sign-off Sheet
Safety Guidelines
Follow Safety Instructions
Use Personal Protective Equipment
PNEG-2286 Metric Aeration Transition 5

Chapter 1: Safety Precautions
Do Not Enter Bin
Prevent Roof Damage due to Vacuum Pressure
6PNEG-2286 Metric Aeration Transition

Chapter 1: Safety Precautions
Unload Bin Correctly
Do Not Overfill the Bin
PNEG-2286 Metric Aeration Transition 7

Chapter 1: Safety Precautions
Stay Clear of Hoisted Equipment Sharp Edge Hazard
Store Bin Sheets Properly
Install and Operate Equipment Properly
Rotating Auger Hazard
8PNEG-2286 Metric Aeration Transition

Chapter 1: Safety Precautions
Safety Decals
To replace a damaged or missing decal, contact GSI to receive a free replacement.
Location Decal No. Decal
A DC-2306
B DC-2161
PNEG-2286 Metric Aeration Transition 9

Chapter 1: Safety Precautions
C DC-2210
Safety Sign-off Sheet
Date Employee Name Supervisor Name
ST-0007
10 PNEG-2286 Metric Aeration Transition

2Aeration Transition Instructions
Topics Covered in this Chapter
▪ Parts List
▪ Installation
Parts List
PNEG-2286 Metric Aeration Transition 11

Chapter 2: Aeration Transition Instructions
12 PNEG-2286 Metric Aeration Transition

Chapter 2: Aeration Transition Instructions
Table 2-1 Hardware list
S.No Part No Description
1 S-BSTM06020 M06 x 20 self-tapping screws
2 CH-6873-M Silicone free cartridge
NOTE: Use silicone free cartridge (2) to seal all joints and make sure there are no air leaks or water
accumulation.
PNEG-2286 Metric Aeration Transition 13

Chapter 2: Aeration Transition Instructions
Installation
Figure 2-1 Assembling the duct top and bottom plates
Figure 2-2 Connecting the duct top and bottom plate assemblies
14 PNEG-2286 Metric Aeration Transition

Chapter 2: Aeration Transition Instructions
Figure 2-3 Assembling the transition side panels with bottom panel
Figure 2-4 Field cut holes on the faceplate for installing the fan discharge
PNEG-2286 Metric Aeration Transition 15

Chapter 2: Aeration Transition Instructions
Figure 2-5 Installing the faceplate and transition assembly to the duct assembly
NOTE: After installing the faceplate (11), use shims at the bottom to make the fan discharge flush with the
transition assembly (14). Once the flush fit is ensured, bolt the fan discharge to the transition
faceplate (11).
Figure 2-6 Installing the transition top panel
16 PNEG-2286 Metric Aeration Transition

Chapter 2: Aeration Transition Instructions
Figure 2-7 Transition and duct assembly dimensions
Figure 2-8 Stemwall transition entrance
PNEG-2286 Metric Aeration Transition 17

Chapter 2: Aeration Transition Instructions
Figure 2-9 Concrete for standard stemwall transition entrance
Figure 2-10 Typical installation of the transition and duct assembly with floor
18 PNEG-2286 Metric Aeration Transition

Chapter 2: Aeration Transition Instructions
Figure 2-11 Transition entrance duct cross section for cor-perforated floor
Figure 2-12 Transition entrance duct cross section for plank floor
PNEG-2286 Metric Aeration Transition 19

Chapter 2: Aeration Transition Instructions
Figure 2-13 Installing the post support weldment inside the duct assembly
Figure 2-14 Marking the stiffener support post location for anchor bolt
20 PNEG-2286 Metric Aeration Transition