7
Assembly Instructions
• Unpack the appliance but keep all packaging materials until you have made sure
your new fan is undamaged and in good working order. Plastic wrapping can be a
suffocation hazard for babies and young children, so ensure all packaging materials
are out of their reach.
• Unwind the cord to its full length and inspect it for damage. Do not use the appliance
if the appliance or its cord have been damaged or are not working properly. In case
of damage, contact our after sales support line for advice on examination, repair or
return of the damaged product.
• Place the fan body onto the base stand and fasten all screws.
• Fit the rear fan grille onto the motor pane: align the 3 holes on the motor with the 3
holes on the rear grille, then insert the 3 screws through the holes and tighten them
rmly.
• Attach the blade onto the motor spindle and carefully tighten the screws.
• Fit the front grille onto the rear grille. Tighten the locking clips to secure the grilles in
place.
TX-901D
220-240V,
MANUAL
WARNING: NEVER PLUG IN THE FAN WHEN IT?S TAKEN APART, THIS MAY CAUSE ELECTRICAL
HAZARDS.
READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS FAN
Safety precautions:
Only connect the fan to an earthed socket with a corresponding voltage as mentioned on the
article.
Use the fan only as described in this manual.
This product is intended for household use ONLY.
Not for commercial, industrial, or use outside.
To protect against electrical shock, do not immerse unit, plug or cord in water or any other liquids.
Do not spray the fan with liquids.
Do not cover the fan
Do not use in humid spaces or near a sink.
Do not use in the presence of explosive and/or highly flammable fumes.
Do not place the article or any part of it near open fire or another heat source.
Place always out of children?s reach.
Always place on a level surface
Remove all objects in the direct vicinity of the article in order not to block the swerving mechanism.
Never put anything through the ventilation roster and always keep under supervision when
switched on.
Do not place near an open window.
Always unplug from socket when:
- not in use
- moving the article from one location to another
- servicing parts, and before
- cleaning the article
Do not use when:
- plug or cord are damaged.
- the article has fallen.
- the article is not functioning properly.
- the article is damaged in any way.
Do not hang or mount fan on a wall or ceiling.
Do not operate without fan grills properly in place.
When the cord is damaged it has to be replace by a recognized electrician.
Stand assembly
1 Assemble the 2 base pieces as a cross. Place the standard onto the base and fasten with the
included 4 philips-head screws (screwdriver not included)
2 Remove the highest adjust screw, pull out the extension tube and make sure that it does not fall
back in. Push the protective cap al the way down over the stand so it falls over the 2 base pieces.
Replace the adjust screw.
3 Place the fan on the extension tube and fasten with the screw.
Instructions for grill assembly
1 Place the back side of the ventilation grille on the motor
spindle. Make sure the security bolt and nut are at the
bottom. Fasten it with the fixing nut.
2 Place the propeller as close as possible to the motor
spindle and fasten it with the fixing nut.
3 Place the front of the grille on the rear. Check that both
grilles properly placed before you close the clamps.
4 Secure the grill by fastening the security bolt and nut.
Users instructions
Place the ventilator on a solid, flat surface
Put the plug into a socket of
By turning the speed button you can select the different
speed options
0- Off
1- Low speed (light breeze)
2- High speed
To activate the swerving you need to pull out the swerving
pin. To stop the swerving press it back down again.
By loosening the turning screw you can select the vertical
the blowing direction
Maintenance/cleaning
Environment friendly disposal
FIRST TAKE THE PLUG OUT OF THE SOCKET
In order to keep the article clean only use it in dry, clean
spaces.
After taking the article apart make you put it back together as described in this manual.
You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working
electrical equipments to an appropriate waste disposal centre.
NEVER put the plug into the socket when article is taken apart!
50/60Hz volt.
220-240V~ 50/60Hz
30W
II
WARNING:
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not use outdoors.
This appliance is not design for outdoor usage.
This appliance is household usage only.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
TX-901D
220-240V,
MANUAL
WARNING: NEVER PLUG IN THE FAN WHEN IT?S TAKEN APART, THIS MAY CAUSE ELECTRICAL
HAZARDS.
READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS FAN
Safety precautions:
Only connect the fan to an earthed socket with a corresponding voltage as mentioned on the
article.
Use the fan only as described in this manual.
This product is intended for household use ONLY.
Not for commercial, industrial, or use outside.
To protect against electrical shock, do not immerse unit, plug or cord in water or any other liquids.
Do not spray the fan with liquids.
Do not cover the fan
Do not use in humid spaces or near a sink.
Do not use in the presence of explosive and/or highly flammable fumes.
Do not place the article or any part of it near open fire or another heat source.
Place always out of children?s reach.
Always place on a level surface
Remove all objects in the direct vicinity of the article in order not to block the swerving mechanism.
Never put anything through the ventilation roster and always keep under supervision when
switched on.
Do not place near an open window.
Always unplug from socket when:
- not in use
- moving the article from one location to another
- servicing parts, and before
- cleaning the article
Do not use when:
- plug or cord are damaged.
- the article has fallen.
- the article is not functioning properly.
- the article is damaged in any way.
Do not hang or mount fan on a wall or ceiling.
Do not operate without fan grills properly in place.
When the cord is damaged it has to be replace by a recognized electrician.
Stand assembly
1 Assemble the 2 base pieces as a cross. Place the standard onto the base and fasten with the
included 4 philips-head screws (screwdriver not included)
2 Remove the highest adjust screw, pull out the extension tube and make sure that it does not fall
back in. Push the protective cap al the way down over the stand so it falls over the 2 base pieces.
Replace the adjust screw.
3 Place the fan on the extension tube and fasten with the screw.
Instructions for grill assembly
1 Place the back side of the ventilation grille on the motor
spindle. Make sure the security bolt and nut are at the
bottom. Fasten it with the fixing nut.
2 Place the propeller as close as possible to the motor
spindle and fasten it with the fixing nut.
3 Place the front of the grille on the rear. Check that both
grilles properly placed before you close the clamps.
4 Secure the grill by fastening the security bolt and nut.
Users instructions
Place the ventilator on a solid, flat surface
Put the plug into a socket of
By turning the speed button you can select the different
speed options
0- Off
1- Low speed (light breeze)
2- High speed
To activate the swerving you need to pull out the swerving
pin. To stop the swerving press it back down again.
By loosening the turning screw you can select the vertical
the blowing direction
Maintenance/cleaning
Environment friendly disposal
FIRST TAKE THE PLUG OUT OF THE SOCKET
In order to keep the article clean only use it in dry, clean
spaces.
After taking the article apart make you put it back together as described in this manual.
You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working
electrical equipments to an appropriate waste disposal centre.
NEVER put the plug into the socket when article is taken apart!
50/60Hz volt.
220-240V~ 50/60Hz
30W
II
WARNING:
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not use outdoors.
This appliance is not design for outdoor usage.
This appliance is household usage only.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
20-240V
MANUAL
WARNING: NEVER PLUG IN THE FAN WHEN IT?S TAKEN APART, THIS MAY CAUSE ELECTRICAL
HAZARDS.
READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS FAN
Safety precautions:
Only connect the fan to an earthed socket with a corresponding voltage as mentioned on the
article.
Use the fan only as described in this manual.
This product is intended for household use ONLY.
Not for commercial, industrial, or use outside.
To protect against electrical shock, do not immerse unit, plug or cord in water or any other liquids.
Do not spray the fan with liquids.
Do not cover the fan
Do not use in humid spaces or near a sink.
Do not use in the presence of explosive and/or highly flammable fumes.
Do not place the article or any part of it near open fire or another heat source.
Place always out of children?s reach.
Always place on a level surface
Remove all objects in the direct vicinity of the article in order not to block the swerving mechanism.
Never put anything through the ventilation roster and always keep under supervision when
switched on.
Do not place near an open window.
Always unplug from socket when:
- not in use
- moving the article from one location to another
- servicing parts, and before
- cleaning the article
Do not use when:
- plug or cord are damaged.
- the article has fallen.
- the article is not functioning properly.
- the article is damaged in any way.
Do not hang or mount fan on a wall or ceiling.
Do not operate without fan grills properly in place.
When the cord is damaged it has to be replace by a recognized electrician.
Foot assembly
1 Place fan on the foot and make sure the electrical cord is lead properly from the article.
2 Hold the article up side down and fasten the 7/8 philips screws
Instructions for assembly
1 Place the back side of the ventilation grille on the motor spindle. Make sure the security bolt and
nut are at the bottom. Fasten it with the fixing nut.
2 Place the propeller as close as possible to the motor spindle and fasten it with the fixing nut.
3 Place the front of the grille on the rear. Check that both grilles properly placed before you close
the clamps.
4 Secure the grill by fastening the security bolt and nut.
Users instructions
Place the ventilator on a solid, flat surface
Put the plug into a socket of 2
By turning the speed button you can select the different speed options
0- Off
1- Low speed (light breeze)
2- Normal speed
3- High speed
To activate the swerving you need to pull out the swerving pin. To stop the swerving press it back
down again.
By loosening the turning screw you can select the vertical the blowing direction
Maintenance/cleaning
FIRST TAKE THE PLUG OUT OF THE SOCKET
In order to keep the article clean only use it in dry, clean spaces.
After taking the article apart make you put it back together as described in this manual.
NEVER put the plug into the socket when article is taken apart!
Environment friendly disposal
You can help protect the environment!
Please remember to respect the local regulations: hand in
the non-working electrical equipments to an appropriate waste disposal centre.
TX-1201D
50/60Hz volt
TECHXIN ELECTRIC APPLIANCE MANUFACTURE CO., LTD
Add: No.36, Haitanwei Zone,Zhoujun Village,Tangxia Town,Jiangmen City Guangdong,China
220-240V~ 50/60Hz
40W
I / II
WARNING:
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not use outdoors.
This appliance is not design for outdoor usage.
This appliance is household usage only.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
TX-901D
220-240V,
MANUAL
WARNING: NEVER PLUG IN THE FAN WHEN IT?S TAKEN APART, THIS MAY CAUSE ELECTRICAL
HAZARDS.
READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS BEFORE USING THIS FAN
Safety precautions:
Only connect the fan to an earthed socket with a corresponding voltage as mentioned on the
article.
Use the fan only as described in this manual.
This product is intended for household use ONLY.
Not for commercial, industrial, or use outside.
To protect against electrical shock, do not immerse unit, plug or cord in water or any other liquids.
Do not spray the fan with liquids.
Do not cover the fan
Do not use in humid spaces or near a sink.
Do not use in the presence of explosive and/or highly flammable fumes.
Do not place the article or any part of it near open fire or another heat source.
Place always out of children?s reach.
Always place on a level surface
Remove all objects in the direct vicinity of the article in order not to block the swerving mechanism.
Never put anything through the ventilation roster and always keep under supervision when
switched on.
Do not place near an open window.
Always unplug from socket when:
- not in use
- moving the article from one location to another
- servicing parts, and before
- cleaning the article
Do not use when:
- plug or cord are damaged.
- the article has fallen.
- the article is not functioning properly.
- the article is damaged in any way.
Do not hang or mount fan on a wall or ceiling.
Do not operate without fan grills properly in place.
When the cord is damaged it has to be replace by a recognized electrician.
Stand assembly
1 Assemble the 2 base pieces as a cross. Place the standard onto the base and fasten with the
included 4 philips-head screws (screwdriver not included)
2 Remove the highest adjust screw, pull out the extension tube and make sure that it does not fall
back in. Push the protective cap al the way down over the stand so it falls over the 2 base pieces.
Replace the adjust screw.
3 Place the fan on the extension tube and fasten with the screw.
Instructions for grill assembly
1 Place the back side of the ventilation grille on the motor
spindle. Make sure the security bolt and nut are at the
bottom. Fasten it with the fixing nut.
2 Place the propeller as close as possible to the motor
spindle and fasten it with the fixing nut.
3 Place the front of the grille on the rear. Check that both
grilles properly placed before you close the clamps.
4 Secure the grill by fastening the security bolt and nut.
Users instructions
Place the ventilator on a solid, flat surface
Put the plug into a socket of
By turning the speed button you can select the different
speed options
0- Off
1- Low speed (light breeze)
2- High speed
To activate the swerving you need to pull out the swerving
pin. To stop the swerving press it back down again.
By loosening the turning screw you can select the vertical
the blowing direction
Maintenance/cleaning
Environment friendly disposal
FIRST TAKE THE PLUG OUT OF THE SOCKET
In order to keep the article clean only use it in dry, clean
spaces.
After taking the article apart make you put it back together as described in this manual.
You can help protect the environment!
Please remember to respect the local regulations: hand in the non-working
electrical equipments to an appropriate waste disposal centre.
NEVER put the plug into the socket when article is taken apart!
50/60Hz volt.
220-240V~ 50/60Hz
30W
II
WARNING:
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not use outdoors.
This appliance is not design for outdoor usage.
This appliance is household usage only.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
