GWS T6 User manual

s »r-' ^
www.gws.com.tw
www.gwsus.com
Instruction Manual
Please read these instructions carefully and thoroughly before
assembly in order to achieve safe operation with maximum
performance from your "GWS-T6 "airplane. Please retain the
manual for future reference
WARNING! This is a hobby kit, not a toy.
Children must be under the strict supervision
of adults who have studied the precautions
given in this manual.
Specifications/Parts list....02
Wing Assembly 03__
Landing Gear Assembly..04^
i
Fuselage Assembly 04
Horizontal/vertical
Stabilizer Assembly 05
Canopy Assembly. 07
Power System Assembly.07
Control System
Assembly 08
Control Throw and center il
of gravity 10 ^
Control system wiring
diagram 11 g,
Decal position suggested |

SPECIFICATIONS
Wing Span :1000 mm (39.4in)
Wing Area : 16.7dm^(258.8sq in)
Lenght = 726mm (28.6in)
FlyingWeight : 500-61 Og (17.6-21.5oz)
Wing Loading : 29.1-35.5g/dm^
(9.79-12.0oz/sq ft)
Propeller ^ EP9050H/EP1080
Radio Required ^ 4CHl^Jl
Receivce ^ GWS-R6N II /R8M/R8MSL
Servo : NAR0X4
Speed Controller ^GWESC25/VICS400Li
Battery Required ^11.1V 1.5Ah Li-Po 9.6V
750mah Ni-Mh
Power System:GWBLM003/EPS350C-CS/EBS2028-BS
I'Mrv 1 0 i_io 1
01.GWST6 Wing(L)
Xl
38.U Shape Canopy Latch B
xl
02.GWST6 Wing(R)
Xl 20.Fiberglass Rod 0 4*2.5*25Omm
xl
39.Ball Shape Latch
x6
03.GWST6 Fuselage(L)
xl 21 .Fiberglass Rod 0 3*1.6*300mm
xl
40.Ball Shape Latch
x6
04.GWST6 Fuselage(L)
xl
22.Tubing(Elevator)3*2*180mm
xl
41.Fire Wall (ABS)
xl
05.GWST6 Horizontal Stabilizer
xl
23.Tubing(Rudder)3*2*220mm
xl
42.Frame A
xl
06.GWST6 Vertical Stabilizer
xl 24.U Shape Connecting Rod 0 1.4mm
xl
43.Frame C
xl
07.GWST6 Battery cover
xl
25.Tubing(Elevator) 01*370mm
xl
44.Clear Tubing 5*2*3 x8
08.Power System Mounting Block
xl
26.Tubing(Rudder)0 1*415mm
xl
45.Pushrod Fixing 1.5
x4
09.GWST6 Engine Cowling
xl
27.Tubing(Aileron)0 1.4*65mm
x2
46.Washer 2.2*5*0.5
x8
10.GWST6 Canopy
xl
28.Pushrod Lock Head 0 1.0
x2
47.Screws M3*4mm
x4
11 .Foam TireA/Vheel o 52mm *
x2
29.Pushrod Lock Head 0 1.4
x2
48.GWS Glue (24g)
xl
12.Foam Tire/Wheel 0 25mm *
xl 30.Y Split Servo Wire W26/24+6
xl
49.30g Clay Stick
xl
13.Tubing 3*2*30mm *
xl 31.3 Motor Power Wire W20/10
xl
50.Spinner xl
14.Tail Landing Gear 1.2*46*11 *
xl
32.Double Side Foam Tape 17.5*20*1mm
x4
51.Washer0 3* *
xl
15.Left Landing Gear 2*115*19 *
xl
33.HexNutM3*5.5*1.8mm x2
52.Screws M3x30mm* *
xl
16.Right Landing Gear 2*115*19*
xl
34.Screws M3*30mm
xl
53.GWST6 Instruction Manual xl
17.Screws M2*10mm *
x6
35.10*18 Hinge Plates
xl
54.GWS Decal
xl
18.Tubing 3*1.2*20mm*
xl 36.Wooden Stick 10*10*90
xl
55.GWST6 Decal(A)
xl
19.Fiberglass Rod 0 4*2.5*38Omm
x2 37.U Shape Canopy Latch A
xl
56.GWST6 Decal(B)
xl
*" Not included In SG kit " * * " Only used for SG kit
GWS-T6 Suggested Power System
Power System
Propeller
Battery
EPS350C-CS
EP1080
8.4-9.6V 750-1200mAh Ni-MH
GWBLM003
11.1V 1.3Ah-2.0Ah(12C)
EP9050H
EBS2028-BS
Required tools before assembly.
TOOLS & MATERIALS
Pliers Screw Driver Hand Drill '^Scissors Triangle Ruler Protractor
Cutting Knife
Masking Tape
E.S.
ICS400
ESC25A
Spray Paint

1. Wing Assembly
Frame"A"
1.3.Cut aileron
as shown
^Fiberglass
Frame"C"
1.4. Secure rods
with glue
l.z.Secure with tape
atemporariiy
1.5. Cut hinge slots
® Fiberglass
1.7.Attach horn
with glue
Fiberglass
I.e.Apply GWS glue to each hinge
and insert into slots on aileron/wing
I ^
i % Hinge %
J \ plate / \
1.8.Glue on plastic
parts 02 and 05
Aileron

2.Landing Gear Assembly
in en
Foam Tire
/ Wheel
5mm ® Tubing 3*2*30
2.1.Cut tubing as shown
2.3.Glue on main
ianding gear
Left Landing Gear
Left Landing//
Gear //
\5mm Tubing
M2x10 Screw
2.2.Assembie main
ianding gears
IRight ianding gear

06
4.8.Cut rudder off as shown
Vertical Stabilizer
4.10.Glue to vertical
stabilizers as shown
3mm ® Tubing 3*1.2*20
4.14.Cut tubing
4.9.Cut hinge slots
o I
I
Jb—TliL.
C) toll 1^
0 0
UiJ to
Frame"C"
Hinge slot
4.12.Giue to vertical-
stabilizers and I
4.11.Glue on tail landing gear rudder as showi)'
lE^Tail landing gear
l,®0
Hinge Plates
Rudder
Smm Tubing
4.13.Attach horn with glue
(1) 25mm Foam Tire/Wheel
4.15.Assemble tail landing gear

5.Canopy Assembly
[SG Spinner asse]

7.Control System Assembly
M3 Screws
i
410mm
\s©Pushrod Fixing
365mm
I Alcohol I
Double Side Foam Tape

Elevator Serw
Receiver
Rudder Serw
@ Elevator Purhrod
Rudder purshrod
7.12.Elicit Antenna
Wive
Pushrod Lock
^ Head 01.0
X 7.8 Assembly
Elevator/Rudder
Serw System
Pushrod Lock
Head 0 1.0
09

8. Control Throw and Center of Gravity
Center of Gravity
Elevator
Control throw
increase horn
Reduce horn
Measure center
of gravity
Rudder
Control angle adjustment
Ai eron
Reduce horn
Increase horn

Control System Wiring Diagram
EPS Power System
EPS400C-FS Electronic Speed
EPS-BR2028-4BS Controller ICS400
Motor Split Wire
Servo Extension Y Split Wire
Propeller
EP1147
EP1080HD
BL2212/13T
BL2215/12T
Propeller
EP-1060HD
GW/R-6N II
Receiver gW/R-SM
GW/R8MSL
Electronic Speed Controller
GW/R-6N II
Receiver GW/R-SM
GW/R8MSL
Receiver system choicej
GW/JR/SANWA
•USTin RECEIVER
^mm.
FM^
Chi. Throttle.
(Electronic speed controller
Gh4. Rudder(Nose Steering)
Channel Assignment for GWS/JR/SANWA
CAUTIONS BEFORE FLIGHT.
9.6V0.75Ah-1.6Ah Nl-Mh
ELEVATOR
FRONT WHEEL/Rudder
GWS Battery
11.1V 1.3Atl(10C*)-2.2Ati(10C*)
Li-Po 9.6V 0.75Ah~1.6Ah Ni-Mti
AILERON
ELEVATOR
FRONT WHEEL/Rudder
Futaba/Hltec
iiS
KEIIM RECEIVER ^
.^r^^NARROW BAND "
g iWM madein TAIWAN
Ch2. Elevator
Ch3. Throttle.
(Electronic speed controller)
Ch4. Rudder(Nose Steering)
Channel Assignment for futaba/hitec
1. Flying field should be wide-open and free of obsticles; do not fly near power lines or buildings.
2. Flight must take place at approved sites; do not fly in restricted air space.
3. Before each flight, make certain that the radio frequency is open to avoid interference.
4. First time flyers, please seek assistance from experienced flyers.
5. Always choose a flat smooth surface for rolling take-offs.

U03'«MB'M«wiv/:du>(
(Blffll
LG
22
Nsn
^5
cccbcb
i?roro
II
o a
K
¥