H3C SecPath NSQM2AC1400 User manual

H3C SecPath NSQM2AC1400
Power Module User Manual
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Document version: APW101-20170414

Copyright © 2016-2017, New H3C Technologies Co., Ltd.
and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of New H3C
Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, ,
H3Care, , IRF, NetPilot, Netflow, SecEngine, SecPath,
SecCenter, SecBlade, Comware, ITCMM and HUASAN are
trademarks of New H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of
any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental
protection requirements. The storage, use, and disposal of this
product must meet the applicable national laws and regulations.

Obtaining documentation
To access the most up-to-date H3C product documentation, go to the
H3C website at http://www.h3c.com.hk
To obtain information about installation, configuration, and
maintenance, click http://www.h3c.com.hk/Technical_Documents
To obtain software version information such as release notes,
click http://www.h3c.com.hk/Software_Download
Technical support
[email protected]
http://www.h3c.com.hk
Documentation feedback
You can e-mail your comments about product documentation to
[email protected].
We appreciate your comments.

i
Contents
Overview ·················································· 1
Front panel ···································································· 2
Technical specifications ··················································· 3
LEDs············································································ 4
Installing and removing the power module······· 6
Installing the power module··············································· 6
Removing the power module············································· 8
Connecting and removing the power cord···························· 8

1
Overview
The NSQM2AC1400 AC-input DC-output power module has the
following features:
•It has a protection mechanism against input undervoltage,
output overvoltage, output short circuit, output overcurrent, and
overtemperature.
•It is hot swappable. You can install and remove the power
module on an operating device when the power switch on the
power module is turned off.
•It can operate in 1+1 redundancy and supports load balancing.

2
Front panel
Figure 1 Front panel
(1) Captive screw (2) Power switch
(3) Status LEDs (4) Power cord retainer
(5) AC power receptacle (6) Handle

3
Technical specifications
Table 1 Technical specifications
Item Specifications
Input voltage range 100 to 240 VAC @ 50/60 Hz
Maximum output current 117 A
Maximum output power •1150 W at 110 VAC
•1400 W at 220 VAC
Dimensions (H × W × D) 128 × 196 × 380 mm (5.04 ×
7.72 × 14.96 in)
Ambient
temperature
Operating
temperature 0°C to 40°C (32°F to 104°F)
Non-operating
temperature –40°C to +70°C (–40°F to +158°F)

4
LEDs
CAUTION:
•The power module restores operation automatically when
the power output alarm, such as short circuit, overcurrent, o
r
overtemperature, is cleared. The power module does not
restore operation automatically when the output overvoltage
alarm is cleared. To restore operation of the power module,
perform the following steps:
a. Turn off the power switch and remove the power cord.
b.Connect the power cord and turn on the power switch.
•Do not frequently turn on or off the power switch. Wait more
than 30 seconds between a turn-on and a turn-off operation.
•After the power switch of the power module is turned off, the
LEDs on the power module will remain on for a while. Make
sure the LEDs are off when you remove the power module.
The power module provides three red/green LEDs: power input LED
(INPUT), power output LED (OUTPUT), and fan status LED (FAN).
Table 2 LED description
LED Status Description
INPUT
Off No power input.
Green Normal power input.
Red Abnormal power input.

5
LED Status Description
OUTPUT
Off No power output.
Green Normal power output.
Red
The power switch is off.
A power output alarm, such as output
short circuit, overcurrent,
overvoltage, or overtemperature, has
occurred. The power module has
entered self-protection mode.
FAN
Off No power input.
Green The fan is operating correctly.
Red
The power switch is off.
The fan is faulty (The power module
enters self-protection mode and stops
power output two seconds after the
fan fails).

6
Installing and removing the power
module
CAUTION:
Do not install the NSQM2AC1400 power module and other types
of power modules on the same device.
To avoid bodily injury and device damage, follow the procedures
in Figure 2 and Figure 3, respectively, to install and remove the
power module.
Figure 2 Procedure for installing the power module
Figure 3 Procedure for removing the power module
Installing the power module
1. Wear an ESD wrist strap and make sure the strap makes good
skin contact and is reliably grounded.
2. Unpack the power module. Make sure the power module meets
the power requirements of the device.
3. Holding the power module handle with one hand and supporting
the bottom with the other, push the power module into the slot
along the guide rails. Make sure the power module makes good
contact with the connectors on the backplane.
Install the power
module Connect the power cord Turn on the power switch