H3C SecPath NSQ1FAB04B0 User manual

Manual version: 6PW106-20210319 BOM: 3123A0R3
i
H3C SecPath NSQ1FAB04B0 switching fabric module
1 Module view
The NSQ1FAB04B0 switching fabric module uses product code NSQM1FAB04B0.
Figure 1 NSQ1FAB04B0 switching fabric module
2 Specifications
Figure 2 Front panel
(1) Status LEDs (2) Console port (CONSOLE)
Table 1 Module specifications
Item Specification
Dimensions (H × W × D) 40 × 256 × 298 mm (1.57 × 10.08 × 11.73 in)
Power consumption 48 W to 65 W
Weight 1.71 kg (3.77 lb)
Hot swapping Supported
Connector type RJ-45
Ports 1 × console port
Ambient temperature Operating: 0°C to 45°C (32°F to 113°F)
Storage: –40°C to +70°C (–40°F to +158°F)

Manual version: 6PW106-20210319 BOM: 3123A0R3
ii
Item Specification
Ambient humidity Operating: 10% RH to 95% RH, noncondensing
Storage: 5% RH to 95% RH, noncondensing
Compatible device models and
slots
•M9006 gateway (slots 6 to 9)
•T9006 IPS (slots 6 to 9)
IMPORTANT:
An M9006 gateway and a T9006 IPS each require a minimum of three switching fabric modules, and
slots 6 and 7 must be installed with switching fabric modules.
3 LEDs
The module provides LEDs to show its operating status.
Table 2 LED description
RUN LED ALM LED Description
Flashing (0.5 Hz) Off The switching fabric module is operating properly.
Off On The switching fabric module is faulty.
Flashing (0.5 Hz) On The temperature of the switching fabric module has exceeded the
upper or lower limit.
Off Off The switching fabric module has not started.
On Off The switching fabric module is starting up.
4 Installing and removing the module
CAUTION:
•Wear a well-grounded ESD-preventive wrist strap before you install or remove the module.
•When you install or remove the module, avoid touching the components on it.
4.1 Installing the module
1. Face the rear panel of the device.
2. Remove the filler panel from the target slot.
This example uses slot 7.
3. Place the module vertically with the component side facing left. Open the ejector levers and
gently push the module into the slot along the guide rails, as shown by callout 1 in Figure 3.
4. Close the ejector levers. Make sure the module is in close contact with the backplane, as shown
by callout 2 in Figure 3.
5. Use a Phillips screwdriver to fasten the captive screws on the module, as shown by callout 3
in Figure 3.

Manual version: 6PW106-20210319 BOM: 3123A0R3
iii
Figure 3 Installing the module
(1) Gently push the module into the slot along the guide rails until the module is in close contact with the
backplane.
(2) Close the ejector levers.
(3) Use a Phillips screwdriver to fasten the captive screws.
(4) Installation is finished.
4.2 Removing the module
1. Use a Phillips screwdriver to loosen the captive screws on the module until all pressure is
released.
2. Simultaneously open the ejector levers on the module to separate the module from the
backplane, and pull the module slowly out of the chassis along the guide rails.
3. Place the module on an anti-static workbench or put it in an anti-static bag, with the component
side facing up.
If you are not to install a new module, install a filler panel in the slot to prevent dust and ensure
good ventilation in the device.
Copyright © 2021 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.