H3C ICT Converged Gateway Series User manual

H3C MSR3610-I
ICT Converged Gateway Series
Hardware Information and Specifications
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 6W100-20201231

Copyright © 2020, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this
document are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage, use,
and disposal of this product must meet the applicable national laws and regulations.

Preface
This document provides hardware information and specifications for the H3C MSR3610-I ICT
converged gateway.
This preface includes the following topics about the documentation:
•
Audience.
•
Conventions.
•
Documentation feedback.
Audience
This documentation is intended for:
•
Network planners.
•
Field technical support and servicing engineers.
•
Network administrators.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention
Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntaxchoices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention
Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.

Symbols
Convention
Description
WARNING!
An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION:
An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT:
An alert that calls attention to essential information.
NOTE:
An alert that contains additional or supplementary information.
TIP:
An alert that provides helpful information.
Network topology icons
Convention
Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
T
T
T
T

Documentation feedback
You can e-mail your comments about product documentation to [e-mail].
We appreciate your comments.

i
Contents
1 Chassis views and technical specifications··············································1-1
Chassis views·················································································································································1-1
MSR3610-I-DP/MSR3610-I-XS/MSR3610-IE-DP/MSR3610-IE-ES/MSR3610-IE-XS····························1-1
MSR3610-IE-EAD···································································································································1-2
MSR3610-I-IG/3610-IE-IG ······················································································································1-2
Power button···········································································································································1-3
Technical specifications··································································································································1-3
Link mode of interfaces···································································································································1-4

1-1
1 Chassis views and technical
specifications
Chassis views
The following figures are for illustration only. The label Hard Disk on the front panel refers to a drive
slot.
MSR3610-I-DP/MSR3610-I-XS/MSR3610-IE-DP/MSR3610-
IE-ES/MSR3610-IE-XS
Figure1-1 Front panel
(1) AC power receptacles PWR1 and PWR2
(2) Drive slot
(3) Power button/LED
(4) USB port
(5) Console port (CONSOLE)
(6) Ethernet fiber port SFP0 (combo interface)
(7) Ethernet fiber port SFP1 (combo interface)
(8) Ethernet copper ports GE0 and GE1 (combo interfaces)
(9) Ethernet copper ports GE2 to GE7
(10) Drive button (HD)
Figure1-2 Rear panel
(1) SIC interface module slots 1 to 4
(2) Grounding screw
12
10
3 4 5 6 7 8 9
1 2

1-2
MSR3610-IE-EAD
Figure1-3 Front panel
(1) AC power receptacles PWR1 and PWR2
(2) Drive slot
(3) Power button/LED
(4) USB port
(5) Console port (CONSOLE)
(6) Ethernet fiber port SFP0 (combo interface)
(7) Ethernet fiber port SFP1 (combo interface)
(8) Ethernet copper ports GE0 and GE1 (combo interfaces)
(9) Ethernet copper ports GE2 to GE7
(10) Drive button (HD)
Figure1-4 Rear panel
(1) SIC interface module slots 3 and 4
(2) SIC-M2-SATA riser modules 1 and 2
(3) Grounding screw
MSR3610-I-IG/3610-IE-IG
Figure1-5 Front panel
(1) AC power receptacles PWR1 and PWR2
(2) Drive slot
(3) Power button/LED
(4) USB port
(5) Console port (CONSOLE)
(6) Ethernet fiber port SFP0 (combo interface)
(7) Ethernet fiber port SFP1 (combo interface)
(8) Ethernet copper ports GE0 and GE1 (combo interfaces)
(9) Ethernet copper ports GE2 to GE7
(10) PoE port
(10) Drive button (HD)
1 2
10
34 5 6 7 89
1 2 3
1 2
11
3 4 5 6 7 8
10
9

1-3
Figure1-6 Rear panel
(1) SIC interface module slots 1 to 4
(2) Grounding screw
Power button
WARNING
!
The
device might still have power after you press the power button. Do not reboot the device or
remove power cords from the device until the power button/LED goes off.
CAUTION:
•
Forced power-off might cause data loss in virtual machines. Please use it with caution.
•
Avoid accidentally pressing the power button when the device is operating. Doing so will power
off the device system and cause service interruption.
The power button is used to power on or power off the Comware system and virtual machines
created on the Comware system.
If you cannot power off the virtual machines gracefully by pressing the power button for 0.5 to 3
seconds, use either of the following methods:
•
Press the power button for over 3 seconds to power off the virtual machines forcibly.
•
Terminate running processes on the virtual machines, and then press the power button to
gracefully power off the virtual machines.
By default, pressing the power button on a powered-off device starts the Comware system but not
the virtual machines. You can use the autostart command to configure the virtual machines to be
started together with the Comware system.
Technical specifications
Table1-1 Technical specifications
Item MSR3610-I-DP/361
0-I-XS
MSR3610-IE-DP/36
10-IE-ES/3610-IE-X
S
MSR3610-IE-E
AD MSR3610-I-IG/36 10-IE-IG
Console port 1 1 1 1
GE copper
ports 2 (combo interfaces) + 6 2 (combo interfaces) + 6 2 (combo interfaces) + 6 2 (combo interfaces) + 6
GE fiber ports 2 (combo interfaces) 2 (combo interfaces) 2 (combo
interfaces) 2 (combo interfaces)
USB port 1 1 1 1
Drive slot 1 (support for a
2.5-inch SATA drive) 1 (support for a 2.5-inch SATA drive) 1 (support for a
2.5-inch SATA
1 (support for a
2.5-inch SATA
12

1-4
Item MSR3610-I-DP/361
0-I-XS
MSR3610-IE-DP/36
10-IE-ES/3610-IE-X
S
MSR3610-IE-E
AD MSR3610-I-IG/36 10-IE-IG
drive)
drive)
SIC interface
module slots 4 4 4 4
AC power
receptacles 2 2 2 2
Memory 8/16/32 GB DDR4 8/16/32 GB DDR4 32 GB DDR4
•MSR3610-I-IG
: 8 GB
•MSR3610-IE-I
G: 16 GB
Built-in
storage 4 GB EMMC 4 GB (64 GB in total)
EMMC 4 GB (64 GB in total) EMMC
•MSR3610-I-IG
: 4 GB EMMC
•MSR3610-IE-I
G: 4 GB (64
GB in total)
EMMC
Dimensions
(H × W × D)
(excluding
mounting
brackets and
rubber feet)
43.6 × 440 × 360 mm
(1.72 × 17.32 × 14.17
in)
43.6 × 440 × 360 mm
(1.72 × 17.32 × 14.17
in)
43.6 × 440 × 360
mm (1.72 ×
17.32 × 14.17 in)
43.6 × 440 × 360
mm (1.72 × 17.32 ×
14.17 in)
Rated AC
voltage 100 VAC to 240 VAC @ 50 or 60 Hz 100 VAC to 240 VAC @ 50 or 60 Hz
100 VAC to 240
VAC @ 50 or 60
Hz
100 VAC to 240
VAC @ 50 or 60 Hz
Maximum
power
consumption 54 W 54 W 54 W 54 W
Operating
temperature
•Without a drive:
0°C to 45°C
(32°F to 113°F)
•With a drive: 5°C
to 40°C (41°F to
104°F)
•Without a drive:
0°C to 45°C
(32°F to 113°F)
•With a drive: 5°C
to 40°C (41°F to
104°F)
•Without a
drive: 0°C to
45°C (32°F
to 113°F)
•With a
drive: 5°C to
40°C (41°F
to 104°F)
•Without a
drive: –20°C to
+55°C (–4°F to
+131°F)
•With a drive:
5°C to 40°C
(41°F to
104°F)
Relative
humidity
(non-condensi
ng)
•Without a drive: 5% RH to 95% RH, noncondensing
•With a drive: 10% RH to 80% RH, noncondensing
Link mode of interfaces
Ethernet interfaces on the device operate differently in link mode. Interfaces that operate in bridge
mode are Layer 2 interfaces. Interfaces that operate in route mode are Layer 3 interfaces.
•
Some fixed Ethernet interfaces on the device operate as Layer 3 Ethernet interfaces by default.
You cannot use the port link-mode command to change the operating mode of these
interfaces to bridge. Table1-2 describes these interfaces.

1-5
•
Some fixed Ethernet interfaces on the device operate as Layer 2 Ethernet interfaces by default.
You can use the port link-mode command to change their operating mode to route.
Table1-3 describes these interfaces.
For information about link mode change of interfaces on interface modules, see H3C MSR Router
Series Comware 7 Interface Module Guide.
Table1-2 Fixed interfaces that can operate only as Layer 3 Ethernet interfaces
Device model Interfaces
MSR3610-I-DP/MSR3610-I-XS/MS
R3610-IE-DP/MSR3610-IE-ES/MS
R3610-IE-XS Combo 0 (GE0, SFP0), Combo 1 (GE1, SFP1)
MSR3610-IE-EAD Combo 0 (GE0, SFP0), Combo 1 (GE1, SFP1)
MSR3610-I-IG/3610-IE-IG Combo 0 (GE0, SFP0), Combo 1 (GE1, SFP1)
Table1-3 Fixed interfaces that operate as Layer 2 interfaces by default and can be changed to
Layer 3 interfaces
Device model Interfaces
MSR3610-I-DP/MSR3610-I-XS/MSR3610-
IE-DP/MSR3610-IE-ES/MSR3610-IE-XS GE2 to GE7
MSR3610-IE-EAD GE2 to GE7
MSR3610-I-IG/3610-IE-IG GE2 to GE7

i
Contents
1 LEDs········································································································1-1
LEDs ·······························································································································································1-1
LED descriptions·············································································································································1-1

1-1
1 LEDs
LEDs
Figure1-1 MSR3610-I-DP/3610-I-XS/3610-IE-DP/3610-IE-ES/3610-IE-XS/3610-IE-EAD LEDs
(1) System status LED (SYS)
(2) Power status LED (PWR1)
(3) Power status LED (PWR2)
(4) LEDs for Ethernet copper ports GE0 to GE7
(5) LEDs for Ethernet fiber ports SFP0 and SFP1
(6) Power button/LED
(7) Drive LED (HD)
Figure1-2 MSR3610-I-IG/3610-IE-IG LEDs
(1) System status LED (SYS)
(2) Power status LED (PWR1)
(3) Power status LED (PWR2)
(4) PoE status LED
(5) LEDs for Ethernet copper ports GE0 to GE7
(6) LEDs for Ethernet fiber ports SFP0 and SFP1
(7) Power button/LED
(8) Drive LED (HD)
LED descriptions
Table1-1 LED descriptions
LED Status Description
System status LED
Fast flashing green BIOS stage BIOS has started successfully.
3
2
1
7
654
2
1
7
3
4
85
6

1-2
LED Status Description
(SYS)
Slow flashing yellow The memory does not exist or system
initialization has failed.
Fast flashing yellow The extended segment does not exist.
Off The system hardware is faulty or the
device has no power input.
Steady green
BootWare
stage
The SDRAM is performing self-test.
Fast flashing green The system software image is being
decompressed.
Slow flashing green Comware is starting up and the
system is operating correctly.
Steady yellow The system software image does not
exist.
Slow flashing yellow The SDRAM has failed the self-test.
Off No power input, or exceptions have
occurred.
Fast flashing green (5
seconds) Comware
stage
The USB disk completed auto
configuration.
Fast flashing yellow (10
seconds) The USB disk has failed auto configuration.
Power button LED
Fast flashing red The power button is being pressed to start up the
Comware system.
Slow flashing red BIOS is starting up.
Slow flashing green BIOS has started and BootWare is starting up.
Steady green The Comware system has started and the device is
operating.
Fast flashing green The power button is being pressed to power off the
Comware system.
Steady red The Comware system is being shutting down.
Off The Comware system has been shut down.
Power status LED
(PWR1 or PWR2) Steady green The power system is operating correctly.
Off No power is being input.
PoE status LED
Steady green Normal PoE input.
Flashing green Abnormal PoE input.
Off No PoE input.
Ethernet copper port
LED
Steady green A 1000 Mbps link is present.
Flashing green The port is receiving or transmitting data at 1000
Mbps.
Steady yellow A 10/100 Mbps link is present.
Flashing yellow The port is receiving or transmitting data at 10/100
Mbps.
Off No link is present.
Ethernet fiber port LED Steady green A 1000 Mbps link is present.

1-3
LED Status Description
Flashing green The port is receiving or transmitting data at 1000
Mbps.
Steady yellow A 100 Mbps link is present.
Flashing yellow The port is receiving or transmitting data at 100 Mbps.
Off No link is present.
Hard disk LED (HD)
Steady green The hard disk has completed initialization.
Flashing green The hard disk is transmitting or receiving data.
Steady yellow The hard disk is faulty.
Off No hard disk is present or the hard disk is faulty.

i
Contents
1 Slot arrangement and interface numbering·················································2

2
1 Slot arrangement and interface
numbering
The fixed ports on the device are defined in slot 0. The device provides four SIC slots. Table1-1
describes the slot arrangement and interface numbering of the device.
Table1-1 Slot arrangement and interface numbering
Slot arrangement
Interface numbering
An interface on a SIC interface module is numbered
in the x/yformat.
•xrepresents the slot number.
•yrepresents the interface number. The
interfaces are numbered from left to right,
starting with 0.
For example, the leftmost interface on a SIC
interface module in slot 2 is numbered GE2/0.
: SIC slots
SIC 1SIC 2SIC 3SIC 4