H3C MSR2600-10-X1 User manual

H3C MSR2600-10-X1 Gigabit Ethernet Integrated Service Gateway Installation Quick Start-6PW101
H3C MSR2600-10-X1 -6PW101
Introduction to installation accessories
Wear an ESD wrist strap, and make sure the wrist strap makes good skin contact and
is reliably grounded.
操作者需佩戴防静电腕带，确保防静电腕带与皮肤良好接触，并确认防静电腕带已经良
好接地。
The installation tools are not provided with the device. Prepare them yourself.
设备不随机提供安装工具，请用户根据实际安装需求自己准备安装工具。
Mounting the device on a workbench
Airflow design of the device
2
1
Flathead screwdriver
一字螺丝刀 Phillips screwdriver 十字螺丝刀 Needle-nose pliers 尖嘴钳 Wire-stripping pliers 剥线钳
ESD wrist strap
防静电腕带
Diagonal pliers
斜口钳 Blow dryer 热吹风 Marker 记号笔
Cage nut
(user-supplied)
浮动螺母(用户自备)
Grounding cable
(provided)
地线(标配)
Stick the rubber feet to the appropriate
positions on the device bottom.
粘贴胶垫到设备底部
Mount the device on a workbench.
将设备安装到工作台
Make sure the air inlet and outlet vents are not blocked and the installation site has a good
ventilation system.
请确保设备的进、出风孔不被遮挡，并将设备安装在具有良好通风散热系统的环境中。
BOM:3104A0JQ
Tool list
!
M4 screw
(provided)
M4 螺钉(标配)
2600-10-X1 bail latch (provided )
2600-10-X1电源线卡钩(标配)
2600-10-X1 mounting brackets (provided)
2600-10-X1 挂耳(标配)
Rubber feet
脚垫
The MSR2600-10-X1 uses left-to-
right aisles.
MSR2600-10-X1采用左进右出的
风道设计

4
3
Connecting the grounding cable
Mount the device in the rack.
安装设备到机柜
To connect the grounding cable when you mount the device on a workbench:
1. Connect one end of the grounding cable to the device and secure it with the grounding
screws provided with the device.
2. Connect the other end of the grounding cable to the building grounding device. If the
installation site has no grounding devices, but earth ground is available, hammer an
angle iron or steel tube into the earth ground to serve as a grounding conductor.
Correctly connecting the device grounding cable is crucial to lightning protection and
EMI protection.设备地线的正确连接是设备防雷、防干扰的重要保障，使用设备随机提供
的保护地线正确接地。
设备安装在工作台时，应将接地线一端与设备相连，并使用随设备提供的两颗接地螺钉固
定，另一端与楼宇接地装置相连。如果安装环境中不具备专用的接地线连接装置也可以采用
埋设接地体的方式将设备妥善接地。
Mounting the device in a rack
Install cage nuts.
安装浮动螺母
Attach the mounting brackets to the device.
安装挂耳到设备

6
5
To connect the grounding cable for rack-mounting:
1. Connect the building grounding cable to the grounding strip on the rack.
2. Connect one end of the grounding cable to the device and the other end to the
grounding strip on the rack. Make sure the rack is reliably grounded.
Connecting the power cord
Before connecting the power cord, make sure the device is reliably grounded. Make
sure the power switch is off and connect the power cord to the device first and then to
the equipment-room power supply system to avoid bodily injury.
在连接电源线前，需保证设备已正确接地。在连接电源线时，请确认设备电源开关处于关
闭状态，先完成电源线与设备的连接，再进行电源线与机房供电系统的连接，以免造成人
身伤害。
设备安装在机柜时，要求机柜已经良好接地，首先需将楼宇保护地线与机柜接地排相连，然后
使用接地线将设备与机柜接地排相连。
Installing a SIC interface card SIC
SIC interface cards are not hot swappable.
SIC接口模块不支持热插拔。
!
To install a SIC interface card:
1. Remove the filler panel from the SIC slot.
2. Insert the SIC interface card.
3. Fasten the captive screws.
安装SIC接口模块：拆卸SIC槽位假面板，插入SIC接口模块，旋紧固定螺钉。

7
Connect one end of the AC power cord to the device and the other end to the power supply
system. Use the bail latch to retain the AC power cord connector for the device. The bail
latch prevents the power cord from falling off.
电源线的两端分别与设备和供电设备紧密相连，并使用电源线卡勾固定，避免因人员走动或
触碰导致电源线的松脱。
Connect the AC power cord.
连接交流电源
To access the most up-to-date H3C product documentation on the H3C website at
www.h3c.com.hk:
1. Go to http://www.h3c.com.hk/Technical_Documents.
2. Choose the desired product category and model.
您可以访问H3C网站（www.h3c.com）获取最新的产品配套资料：
1. 请访问网址：http://www.h3c.com/cn/Technical_Documents；
2. 选择产品类别和产品型号，即可查询和下载与该产品相关的手册。
Obtaining documentation
Copyright © 2017, New H3C Technologies Co., Ltd.
For more information about the product and installation procedures, log in to www.h3c.com.hk
Copyright © 2017 新华三技术有限公司 版权所有，保留一切权利。
如需了解产品及安装方面的更多信息，请登录H3C网站 www.h3c.com