H3C SecCenter CSAP-SA User manual

H3C SecCenter
CSAP-SA
Installation Guide
New H3C Technologies Co., Ltd.
http://www.h3c.com
Document version: 5W100-20220329

Copyright © 2022, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
Except for the trademarks of New H3C Technologies Co., Ltd., any trademarks that may be mentioned in this
document are the property of their respective owners.
Notice
The information in this document is subject to change without notice. All contents in this document, including
statements, information, and recommendations, are believed to be accurate, but they are presented without
warranty of any kind, express or implied. H3C shall not be liable for technical or editorial errors or omissions
contained herein.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage, use,
and disposal of this product must meet the applicable national laws and regulations.

Preface
This installation guide describes the procedure for installing servers of the H3C SecCenter CSAP-S
threat discovery and security operations platform, H3C SecCenter CSAP-C threat discovery and
security operations platform, and H3C SecCenter CSAP-SA log audit platform.
This preface includes the following topics about the documentation:
•Audience.
•Conventions.
•Documentation feedback.
Audience
This documentation is intended for:
•Network planners.
•Field technical support and servicing engineers.
•Network administrators.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention
Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntax choices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention
Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For

Convention
Description
example, File > Create > Folder.
Symbols
Convention
Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION: An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT:
An alert that calls attention to essential information.
NOTE: An alert that contains additional or supplementary information.
TIP:
An alert that provides helpful information.
Network topology icons
Convention
Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
T
T
T
T

Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
Documentation feedback
You can e-mail your comments about product documentation to [e-mail].
We appreciate your comments.

i
Contents
Safety information ············································································1
Safety sign conventions···············································································································1
Power source recommendations ···································································································1
Installation safety recommendations ······························································································2
General operating safety·······································································································2
Electrical safety···················································································································2
Rack mounting recommendations···························································································2
ESD prevention···················································································································3
Cooling performance············································································································3
Battery safety ·····················································································································3
Preparing for installation····································································1
Space requirements ···················································································································1
Installation site requirements········································································································1
Airflow direction of the server·································································································1
Temperature and humidity requirements ··················································································1
Equipment room height requirements ······················································································2
Cleanliness requirements······································································································2
Grounding requirements ·······································································································2
Installation tools·························································································································2
Installing or removing the server··························································1
Installing the server ····················································································································1
Installing rails ·····················································································································1
Rack-mounting the server ·····································································································1
Installing cable management brackets ·····················································································2
Connecting external cables··········································································································2
Cabling guidelines···············································································································2
Connecting a mouse, keyboard, and monitor·············································································2
Connecting an Ethernet cable ································································································4
Connecting a USB device ·····································································································5
Connecting the power cord····································································································6
Securing cables ··················································································································8
Removing the server from a rack···································································································9
Installing hardware options·································································1
Installing drives ·························································································································1
Installing power supplies··············································································································2
Installing a PCIe network adapter··································································································3
Installing DIMMs························································································································5
About DIMMs ·····················································································································5
Guidelines ·························································································································5
Powering on and powering off the server···············································1
Important information··················································································································1
Powering on the server ···············································································································1
Prerequisites······················································································································1
Procedure··························································································································1
Powering off the server ···············································································································2
Guidelines ·························································································································2
Procedure··························································································································2
Replacing hardware options ·······························································1
Replacing the security bezel·········································································································1
Removing the security bezel··································································································1
Installing the security bezel····································································································1
Replacing a drive·······················································································································2

ii
Replacing the access panel··········································································································3
Removing the access panel···································································································3
Installing the access panel ····································································································4
Replacing a power supply············································································································5
Replacing the chassis air baffle·····································································································7
Removing the chassis air baffle······························································································7
Installing the chassis air baffle································································································7
Replacing a PCIe network adapter·································································································8
Replacing a fan ·······················································································································10
Removing a fan················································································································· 10
Installing a fan ··················································································································11
Verifying the installation······································································································ 11
Replacing a DIMM····················································································································12
Replacing the system battery······································································································ 13
Removing the system battery·······························································································13
Installing the system battery ································································································14
Verifying the replacement····································································································14
Technical support·············································································1
Collecting fault information···········································································································1
Preparing tools··························································································································1

1
Safety information
Safety sign conventions
To avoid bodily injury or damage to the server or its components, make sure you are familiar with the
safety signs on the server chassis or its components.
Table 1 Safety signs
Sign Description
Circuit or electricity hazards are present. Only H3C authorized or
professional server engineers are allowed to service, repair, or
upgrade the server.
WARNING!
To avoid bodily injury or damage to circuits, do not open any
components marked with the electrical hazard sign unless you have
authorization to do so.
Electrical hazards are present. Field servicing or repair is not allowed.
WARNING!
To avoid bodily injury, do not open any components with the
field-servicing forbidden sign in any circumstances.
The surface or component might be hot and present burn hazards.
WARNING!
To avoid being burnt, allow hot surfaces or components to cool before
touching them.
The server or component is heavy and requires more than one people
to carry or move.
WARNING!
To avoid bodily injury or damage to hardware, do not move a heavy
component alone. In addition, observe local occupational health and
safety requirements and guidelines for manual material handling.
The server is powered by multiple power supplies.
WARNING!
To avoid bodily injury from electrical shocks, make sure you disconnect
all power supplies if you are performing offline servicing.
Power source recommendations
Power instability or outage might cause data loss, service disruption, or damage to the server in the
worst case.
To protect the server from unstable power or power outage, use uninterrupted power supplies
(UPSs) to provide power for the server.

2
Installation safety recommendations
To avoid bodily injury or damage to the server, read the following information carefully before you
operate the server.
General operating safety
To avoid bodily injury or damage to the server, follow these guidelines when you operate the server:
•Only H3C authorized or professional server engineers are allowed to install, service, repair,
operate, or upgrade the server.
•Place the server on a clean, stable table or floor for servicing.
•Make sure all cables are correctly connected before you power on the server.
•To avoid being burnt, allow the server and its internal modules to cool before touching them.
Electrical safety
WARNING!
If you put the server in standby mode (system power LED in amber) with the power on/standby
button on the frontpanel, the power supplies continue to supply
power to some circuits in the server.
To remove all power for servicing safety, you must
first press the button, wait for the system to enter
standby mode, and then remove the power cords from the server.
To avoid bodily injury or damage to the server, follow these guidelines:
•Always use the power cords that came with the server.
•Do not use the power cords that came with the server for any other devices.
•Power off the server when installing or removing any components that are not hot swappable.
Rack mounting recommendations
To avoid bodily injury or damage to the equipment, follow these guidelines when you rack mount a
server:
•Mount the server in a standard 19-inch rack.
•Make sure the leveling jacks are extended to the floor and the full weight of the rack rests on the
leveling jacks.
•Couple the racks together in multi-rack installations.
•Load the rack from the bottom to the top, with the heaviest hardware unit at the bottom of the
rack.
•Get help to lift and stabilize the server during installation or removal, especially when the server
is not fastened to the rails. As a best practice, a minimum of two people are required to safely
load or unload a rack.A third person might be required to help align the server if the server is
installed higher than check level.
•For rack stability, make sure only one unit is extended at a time. A rack might get unstable if
more than one server unit is extended.
•Make sure the rack is stable when you operate a server in the rack.
•To maintain correct airflow and avoid thermal damage to the server, use blank panels to fill
empty rack units.

3
ESD prevention
Electrostatic charges that build up on people and tools might damage or shorten the lifespan of the
system board and electrostatic-sensitive components.
Preventing electrostatic discharge
To prevent electrostatic damage, follow these guidelines:
•Transport or store the server with the components in antistatic bags.
•Keep the electrostatic-sensitive components in separate antistatic bags until they arrive at an
ESD-protected area.
•Place the components on a grounded surface before removing them from their antistatic bags.
•Avoid touching pins, leads, or circuitry.
Grounding methods to prevent electrostatic discharge
The following are grounding methods that you can use to prevent electrostatic discharge:
•Wear an ESD wrist strap and make sure it makes good skin contact and is reliably grounded.
•Take adequate personal grounding measures, including wearing antistatic clothing and static
dissipative shoes.
•Use conductive field service tools.
•Use a portable field service kit with a folding static-dissipating work mat.
Cooling performance
Poor cooling performance might result from improper airflow and poor ventilation and might cause
damage to the server.
To ensure good ventilation and proper airflow, follow these guidelines:
•Install blanks if the following module slots are empty:
Drive bays.
Fan bays.
PCIe slots.
Power supply slots.
•Do not block the ventilation openings in the server chassis.
•To avoid thermal damage to the server, do not operate the server for long periods in any of the
following conditions:
Access panel open or uninstalled.
Air baffles uninstalled.
PCIe slots, drive bays, fan bays, or power supply slots empty.
•If you stack devices in a rack, make sure a minimum of 2 mm (0.08 in) space is available
between two vertically adjacent devices.
Battery safety
The server's system board contains a system battery, which is designed with a lifespan of 5 to 10
years.
If the server no longer automatically displays the correct date and time, you might need to replace
the battery. When you replace the battery, follow these safety guidelines:
•Do not attempt to recharge the battery.

4
•Do not expose the battery to a temperature higher than 60°C (140°F).
•Do not disassemble, crush, puncture, short external contacts, or dispose of the battery in fire or
water.
•Dispose of the battery at a designated facility. Do not throw the battery away together with other
wastes.

1
Preparing for installation
Prepare a rack that meets the rack requirements and plan an installation site that meets the
requirements for space and airflow, temperature, humidity, equipment room height, cleanliness, and
grounding.
Space requirements
The cabinet for installing the server must meet the following requirements:
•A minimum clearance of 635 mm (25 in) in front of the cabinet.
•A minimum clearance of 762 mm (30 in) behind the cabinet.
•A minimum clearance of 1219 mm (47.99 in) between two adjacent cabinets.
Installation site requirements
Airflow direction of the server
Figure 1 Airflow direction of the server
(1) to (4) Directions of the airflow into the chassis and power supplies
(5) to (7) Direction of the airflow out of the chassis (8) Direction of the airflow out of the power supplies
Temperature and humidity requirements
To ensure correct operation of the server, make sure the room temperature and humidity meet the
requirements as described in Table 2.
Table 2 Temperature and humidity requirements
Item Description
Temperature •Operating temperature: 0°C to 45°C (32°F to 113°F)
•Storage temperature: –40°C to +70°C (–40°F to +158°F)
Humidity •Operating humidity: 8% to 90%, non-condensing
•Storage humidity: 5% to 95%, non-condensing
Operating altitude –60 m to +3000 m (–196.85 ft to +9842.52 ft)
The allowed maximum temperature decreases by 0.33 °C (32.59°F) as the altitude

2
increases by 100 m (328.08 ft) from 900 m (2952.76 ft)
Storage altitude –60 m to +5000 m (–196.85 ft to +16404.20 ft)
Equipment room height requirements
To ensure correct operation of the server, make sure the equipment room height meets the
requirements as described in "Appendix A Server specifications."
Cleanliness requirements
Mechanically active substances buildup on the chassis might result in electrostatic adsorption,which
causes poor contact of metal components and contact points. In the worst case, electrostatic
adsorption can cause communication failure.
Table 3 Mechanically active substance concentration limit in the equipment room
Substance Particle diameter Concentration limit
Dust particles ≥ 5 µm ≤ 3 x 104particles/m3
(No visible dust on desk in three days)
Dust (suspension) ≤75 µm ≤0.2 mg/m3
Dust
(sedimentation) 75 µm to 150 µm ≤1.5 mg/(m2h)
Sand ≥ 150 µm ≤30 mg/m3
The equipment room must also meet limits on salts, acids, and sulfides to eliminate corrosion and
premature aging of components, as shown in Table 3.
Table 4 Harmful gas limits in an equipment room
Gas Maximum concentration (mg/m3)
SO20.2
H2S 0.006
NO20.04
NH30.05
Cl20.01
Grounding requirements
Correctly connecting the server grounding cable is crucial to lightning protection, anti-interference,
and ESD prevention. The server can be grounded through the grounding wire of the power supply
system and no external grounding cable is required. Make sure the resistance between the server
chassis and the ground is less than 10 Ω.
Installation tools
Table 4 lists the tools that you might use during installation.

3
Table 5 Installation tools
Picture Name Description
T25 Torx screwdriver Installs or removes screws inside chassis ears. A
flathead screwdriver can also be used for this purpose.
T15 Torx screwdriver
(shipped with the server) Installs or removes the screw on the access panel.
T10 Torx screwdriver
(shipped with the server) Installs or removes screws on riser card blanks.
Flat-head screwdriver Installs or removes the system battery.
Cage nut insertion/extraction
tool Inserts or extracts the cage nuts in rack posts.
Diagonal pliers Clips insulating sleeves.
Tape measure Measures distance.
Multimeter Measures resistance and voltage.
ESD wrist strap Prevents ESD when you operate the server.
Antistatic gloves Prevents ESD when you operate the server.
Antistatic clothing Prevents ESD when you operate the server.
Ladder Supports high-place operations.

4
Picture Name Description
Interface cable (such as an
Ethernet cable or optical
fiber) Connects the server to an external network.
Monitor Displays the output from the server.

1
Installing or removing the server
To install hardware options, first install the options and then rack-mount the server. For more
information, see "Installing hardware options."
Installing the server
Installing rails
Install the inner rails to the server and the outer rails to the rack. For information about installing the
rails, see the document shipped with the rails.
Rack-mounting the server
1. Slide the server into the rack. For more information about how to slide the server into the rack,
see the installation guide for the rails.
Figure 2 Rack-mounting the server
2. Secure the server as shown in Figure 3.
a. Push the server until the multifunctional rack mount ears are flush against the rack front
posts, as shown by callout 1.
b. Unlock the latches of the multifunctional rack mount ears, as shown by callout 2.
c. Fasten the captive screws inside the chassis ears and lock the latches, as shown by callout
3.

2
Figure 3 Securing the server
Installing cable management brackets
Install cable management brackets if the server is shipped with cable management brackets. For
information about how to install cable management brackets, see the installation guide shipped with
the brackets.
Connecting external cables
Cabling guidelines
WARNING!
To avoid electric shock, fire,or damage to the equipment, do not connect communication equipment
to RJ-45 Ethernet ports on the server.
•For heat dissipation, make sure no cables block the inlet or outlet air vents of the fan modules,
heatsinks, GPUs, and PSUs.
•To easily identify ports and connect/disconnect cables, make sure the cables do not cross.
•Label the cables for easy identification of the cables.
•Wrap unused cables onto an appropriate position on the rack.
•To avoid damage to cables when extending the server out of the rack, do not route the cables
too tight if you use cable management brackets.
Connecting a mouse, keyboard, and monitor
About this task
Perform this task before you configure HDM or enter the operating system of the server.
The server provides one DB15 VGA connector for connecting a monitor. The server is not shipped
with a standard PS2 mouse and keyboard. To connect a PS2 mouse and keyboard, you must
prepare a USB-to-PS2 adapter.

3
Procedure
1. Connect one plug of a VGA cable to a VGA connector on the server, and fasten the screws on
the plug.
Figure 4 Connecting a VGA cable
2. Connect the other plug of the VGA cable to the VGA connector on the monitor, and fasten the
screws on the plug.
3. Connect the mouse and keyboard.
For a USB mouse and keyboard, directly connect the USB connectors of the mouse and
keyboard to the USB connectors on the server.
For a PS2 mouse and keyboard, insert the USB connector of the USB-to-PS2 adapter to a
USB connector on the server. Then, insert the PS2 connectors of the mouse and keyboard
into the PS2 receptacles of the adapter.
Figure 5 Connecting a PS2 mouse and keyboard by using a USB-to-PS2 adapter

4
Connecting an Ethernet cable
About this task
Perform this task before you set up a network environment or log in to the HDM management
interface through the HDM network port to manage the server.
Procedure
1. Determine the network port on the server.
To connect the server to the external network, use one of the four Ethernet ports on the rear
panel.
To log in to the HDM management interface, use the HDM dedicated network port or the
HDM shared network port (Ethernet interface 1) on the rear panel. For the location of the
network ports, see "Rear panel."
2. Determine type of the Ethernet cable.
Verify the connectivity of the cable by using a link tester.
If you are replacing the Ethernet cable, make sure the new cable is the same type or compatible
with the old cable.
3. Label the Ethernet cable by filling in the names and numbers of the server and the peer device
on the label.
As a best practice, use labels of the same kind for all cables.
If you are replacing the Ethernet cable, label the new cable with the same number as the
number of the old cable.
4. Connect one end of the Ethernet cable to the network port on the server and the other end to
the peer device.
Figure 6 Connecting an Ethernet cable
5. Verify network connectivity.
After powering on the server, use the ping command to test the network connectivity. If the
connection between the server and the peer device fails, verify that the Ethernet cable is
securely connected.
6. Secure the Ethernet cable. For information about how to secure cables, see "Securing cables."

5
Connecting a USB device
About this task
Perform this task before you install the operating system of the server or transmit data through a
USB device.
The server provides a maximum of five USB connectors.
•Three USB connectors on the front and rear panels.
•Two internal USB connectors for connecting USB devices that are not designed to be installed
and removed very often.
Guidelines
Before connecting a USB device, make sure the USB device can operate correctly and then copy
data to the USB device.
USB devices are hot swappable.
As a best practice for compatibility, purchase H3C-certified USB devices.
Procedure
1. (Optional.) Remove the access panel if you need to connect the USB device to an internal USB
connector. For information about how to remove the access panel, see "Removing the access
panel."
2. Connect the USB device to the USB connector, as shown in Figure 7.
Figure 7 Connecting a USB device to an internal USB connector
3. (Optional.) Install the access panel. For information about how to install the access panel, see
"Installing the access panel."
4. Verify that the server can identify the USB device.
If the server fails to identify the USB device, download and install the driver of the USB device.
If the server still fails to identify the USB device after the driver is installed, replace the USB
device.