hager 47PN User manual

INSTALL RIM CYLINDER THROUGH WAVE WASHER, CYLINDER SPACER A.
RING (IF NEEDED) AND COLLAR. THE THINNER COLLAR PROVIDED WITH
THE RIM CYLINDER CAN BE USED FOR 1-1/8" LONG CYLINDERS ONLY.
INSERT RIM CYLINDER THROUGH HOLE IN PULL PLATE AND INSTALL B.
SPACER AND CYLINDER CUP FROM THE BACKSIDE OF THE
PULL PLATE.
SECURE RIM CYLINDER ASSEMBLY USING THE 2 BREAK OFF SCREWS C.
PROVIDED WITH THE RIM CYLINDER.
STEP 1: INSTALL CYLINDER (SKIP TO STEP "2" FOR DUMMY PULL PLATE - 47PD)
RIM CYLINDER
1-1/8" TO 1-3/8" LONG
IC OR STANDARD
CORE
WAVE
SPRING
WASHER
CYLINDER
SPACER
RING
CYLINDER COLLAR FOR
1-1/4 TO 1-3/8" LONG CYLINDERS
CYLINDER COLLAR - PROVIDED WITH CYLINDER
FOR 1-1/8" LONG CYLINDERS ONLY
SPACER
BREAK-OFF SCREWS
CYLINDER CUP AND
TAILPIECE GUIDE
TAB MUST FIT INTO
SLOT ON SPACER
TAB MUST FIT INTO
SLOT ON PULL PLATE
BREAK-OFF SCREWS
PROVIDED WITH
RIM CYLINDER
TRANSFER HORIZONTAL CENTERLINE AND BACKSET A.
CENTERLINE FROM EXIT DEVICE SIDE OF THE DOOR.
USE TEMPLATE OR DIMENSIONS FROM PAGE 2 TO MARK B.
HOLE LOCATIONS.
DRILL THREE
1/2" CLEARANCE HOLES FOR MOUNTING POSTS. C.
DRILL 1-3/4" CLEARANCE HOLE FOR THE CYLINDER. D.
INSERT PULL PLATE MOUNTING POSTS THROUGH DOOR. E.
RIM CYLINDER TAILPIECE SHOULD INSERT INTO THE EXIT DEVICE F.
CAM APPROXIMATELY 7/16" 1/16". IF IT'S TOO LONG, CAREFULLY
MEASURE AND MARK AT THE CLOSEST BREAK-OFF LINE. THEN USE
PLYERS TO BREAK-OFF ACCESS, CAREFULLY NOT TO BREAK-OFF
TOO MUCH.
SECURE PULL PLATE AND EXIT DEVICE USING THE 3 MOUNTING G.
SCREWS.
STEP 2: INSTALL PULL PLATE
1/4"-20 PAN HEAD
MACHINE SCREW (2X)
4700 EXIT DEVICE
HEAD CHASSIS
1-3/4" CYLINDER HOLE (1X)
1/2" MOUNTING HOLES (3X)
1/4"-20 FLAT HEAD
MACHINE SCREW (1X)
SCREW COLLAR
DOOR
SHEET 1 OF 2
47PN & 47PD PULL PLATE INSTRUCTIONS
FOR USE WITH 4700 SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - [phone] - Fax [phone] DRAWING NO: I-ED00264 REV: 01

.24
6
1.49
37.9
.45
11.3
1.62
41.1
.08
2
1.68
42.5
EXIT DEVICE
C
L
(SEE NOTE 1)
RIM CYLINDER
C
L
3.00
76.2
R .75
19.1
2.81
71.4
1.43
36.3
5.93
150.6
1.58
40.1
11.75
298.5
.24
6
1.50
38.1
1.50
38.1
2.88
73
5.44
138.2
1.44 36.5
1.44 36.5
6.88
174.7
REQUIRES A
0.50"
CLEARANCE HOLE
THROUGH DOOR (3X)
REQUIRES A
1.75"
CLEARANCE HOLE
THROUGH DOOR
PULL PLATE
C
L
CORRESPONDS TO
EXIT DEVICE
C
L
NOTES:
MATCH THIS CENTERLINE UP WITH THE EXIT DEVICE CENTERLINE. 1.
THIS WILL ENSURE THE RIM CYLINDER TAILPIECE LINES UP WITH THE
EXIT DEVICE TAILPIECE CAM.
PULL PLATE
C
L
CORRESPONDS TO
EXIT DEVICE
C
L
47PN & 47PD PULL PLATE INSTRUCTIONS
FOR USE WITH 4700 SERIES EXIT DEVICES
HAGER COMPANIES
139 Victor Street, St. Louis, MO 63104 - [phone] - Fax [phone]
REV: 01 DRAWING NO: I-ED00264 SHEET 2 OF 2