Haier Tiana HW1007NZP User manual

Automatic Drum Washer-dryer
HW100-HB1297NZP
User Manual
Please read these instructions carefully before use.
Please save these instructions for future reference.

/

Product Features
DD inverter frequency motor technology Function (Stop just in time upon cleanness)
Hybrid balance technology Drawer-type box
Inclined drum Function of Supporter Dry
Large capacity Self-cleaning function
Optimal door height design Air-wash function
Large-caliber clothes-loading opening Technology of anti-bacteria and mildew-proof with
JIT function (Stop just in time upon
drying)
window pad
Large high-brightness LCD
Specifications
Washing noise (sound pressure level/sound power level)
Spinning noise (sound pressure level/sound power level)
The diagrams in this manual are for illustrative purpose only. Due to continuous product improvement,
pleasesee the actual product for appearance, color and accessories which may be inconsistent with
those described in this manual. Here we apologize for this.
This product is classified as Class I appliance. Please pay attention to electrical safety during use.
* : Please ensure that
Water inlet pressure is higher than 0.03 MPa while drying.
Power supply
Water inlet pressure
Rated washing capacity
Rated spinning capacity
Rated drying capacity
Spinning speed
Overall dimensions(H×D×W)
220-240V~/50Hz
(0.001-1.0)MPa *
10kg
10kg
8kg
1200rpm
36dB(A)/49dB(A)
54dB(A)/63dB(A)
1200mm×639mm×699mm

15 Fault Diagnosis and Solution
Displayed
code Code meaning Solution
The washer is in automatic weighing state Normal prompt
Code for the clothes weight:
X=1(i.e. AL-1) displays when there are no clothes or less than 2kg clothes in the
washer-dryer;
X=2(i.e. AL-2) displays when there are about 2-4kg clothes in the washer-dryer;
X=3(i.e. AL-3) displays when there are about 4-6kg clothes in the washer-dryer;
X=4(i.e. AL-4) displays when there are about 6-8kg clothes in the washer-dryer;
X=5(i.e. AL-5) displays when there are about 8-10kg clothes in the washer-dryer.
Normal prompt
Being inconsistent with the conditions
for door opening,it is not allowed to
unlock the door
Normal prompt
Normal prompt
Normal prompt
Close the door ; if the code remains,please ask for repair
Check whether the outlet of drain pipe is 10cm above the floor;
Clean the drain filter and check whether the drain pipe is
clogged;if the code remains, please ask for repair
Check whether the water tap is turned on, whether the water
pressure istoo low ,whether power supply cut-off occurs.Press
the “Start/Pause” button to clear it, if the code remains,please
ask for repair
Check whether the outlet of drain pipe is 10cm above the floor;
Clean the drain filter and check whether the drain pipe is
clogged;if the code remains, please ask for repair
Check the adjsuyable feet to confirm whether the washer-dryer
is level;
Take out and fluff out the clothes;if the code remains,please ask
for repair
Take out some clothes
Reinstall the drying filter; if the code remains,please ask for
repair
Abnormal drying filter
Child lock prompt
The whole program ends
Abnormal door locking or unclosed
door
Drainage faulr (The words “Drain
Filter” on the display screen flash)
Abnormal water feed
Abnormal drying water level
Unbalanced clothes distribution when
spinning(The words “Imbalance” on the
display screen flash)
The clothes weight is beyond the
acceptable range (The words
“Overload” on the display screen flash)
In case of the following alarms, press the “Off” button to clear them. If they remain, unplug the power plug and contact our
After-sales Service Department.In case of the following alarms, press the “Off” button to clear them. If they remain, unplug the power
plug and contact our After-sales Service Department.
Contents
1 Safety Precautions 1
2 Precautions for Use
2
3 Components 4
4 Accessories
5
5 Notice before Use
5
6 Control Panel and Program Description
9
7 Display Screen
11
8 Programs Guide
13
9 Operational Procedures
14
10 General Program Running Process
15
11 Preparations before Washing
16
12 Reference Weight for Different Types of Clothing
16
13 Other Functions
17
14 Cleaning/Maintenance
19
15 Fault Diagnosis and Solution 21
23

1 Safety Precautions
The plug should be accessible after the washer-dryer is installed in place. Do
not disconnect the plug from the socket by pulling the power cord. If the
power cord needs to be replaced, ask a qualified technician or contact our
After-sales Service Department for replacement. Prevent the power cord
from being pressed by any foot and from such problems as break-off, flattening, etc.
Power supply must use an independent socket, the grounding terminal of which must be
properly grounded. The socket must be a qualified product.
Such overload protective devices as proper fuse must be available at the user’s home.
And, the ammeter, wire and socket must be able to withstand 10A current.
Keep the washer-dryer away from any heat source and direct sunlight to prevent the aging of
plastic and rubber parts.
Do not use such chemicals as flammable detergent and dry-cleaning solvent to wash the clothes. Do
not use any flammable spray near the washer-dryer. In case of flammable gas leakage, do not plug or
unplug the washer-dryer’s power plug.
The washer-dryer’s door and tabletop panel are relatively hot during heating and drying. For
the purpose of safety, keep the children away from the washer-dryer. In addition, when
draining hot water, be careful to avoid scald.
After unpacking the washer-dryer, do not allow the children to play with the disassembled
packaging materials such as carton, plastic packaging bag and foam, etc.
Do not install the washer-dryer outdoors and in excessively humid environment, otherwise moisture on
the electrical components may easily cause damage to the ignition system or other accidents. In case of
inadvertent water spray onto or into the washer-dryer, only after the washer-dryer is thoroughly dried
can you use it.
Neither should you place the washer-dryer directly onto an airproof carpet in order not to block the
bottom vent, nor place it close up to the wall or furniture to avoid accidents. Do not use the
washer-dryer on any platform above the floor, otherwise it may fall off onto the floor and be damaged.
Electrical safety prompt:
Please pay attention to electrical safety during use.
Warning sign:
The contents with this sign involve the safety of both the product and the user.
Be sure to strictly follow these instructions, otherwise the washer-dryer
may be damaged or the user may be injured.
Prohibitory sign:
The contents with this sign indicate the behaviors to be absolutely
prohibited. Failure to follow these instructions may result in damage to the
washer-dryer or personal injury.
22
State
When
rinse
When
drain
When
spin
Others
Phenomenon Solution
Poor washing effect
Forceless washing
Stop operation during washing
Repeated rinsing
No spinning
Loud noise when spinning
Vibration and displacement
The clothes are not spun dry agter
finishing the spinning progran
No water discharge or slow water
discharge
The control panel is partially hot
The washing does not end after the
preset delay time
The washer-dryer’s program is set with discharge time and the
spinning starts after a period of time
Check whether the clothes intertwist
Check whether all the packaging bolts are removed
Check whether the clothes intertwist
Check whether the washer-dryer collides with other objects
Check whether there are forergn bodies in the washer-dryer
The spinning effect varies with type of clothes
Check whether eccentric protection functions due to few clothes
Check whether thedrain pipe is bent, clogged or frozen
Check whether the outlet of drain pipe is 10cm above the floor
Check whether the filter is clogged
It is normal that electronic components are a bit hot
Poor water feeding/drainage conditions or unbalanced clothes
distribution results in longer time
Check whether the washer-dryer is level (The feet can be
adjusted to level the washer)
Check whether sudden power failure or power supply cut-off
occurs
Check whether the “Srart/Pause” button is pressed
The washer-dryer with the function of automatic shutdown upon
clean detected automatically increases or decreases the times
of rinsing (1-2 times) according to the degree of dirtiness of the
clothes
Check the detergent for proper type and dosage
Check whether a proper program is selected
Check whether the clothes weight exceeds the washer-dryer’s
rated washing capacity
When
wash
1

21
15 Fault Diagnosis and Solution
State Phenomenon Solution
Before operation
There is a small amount of water in
the drain pipe and washer-dryer when
using for the first time
The washer-dryer does not operate
Check whether power failure or abnormal power supply occurs
Check whether the power plug is firmly plugged in the socket
Check whether the fuse of power supply or the current breaker
is in good condition
Check whether the power switch is pressed
Check whether the water tap is turned on
Check whether the “delay” function is activated
Check whether the “Start/Pause” button is pressed
Check whether the water tap is tured on and whether water
supply cut-off occurs
Check whether the washer-dryer inclines or shakes
Abnormal noise
Check whether there are foreign bodies such as coins and
zippers in the washer-dryer
Check whether the noise is from the draining pump or motor in
normal operation
Check whether the water inlet filter screen is clogged (If
necessary clean it)
Check whether the water tap and water inlet pipe are frozen
Check whether the “Delay” program is selected
Check whether the “Start/Pause” button is pressed
Check whether the water inlet pipe is bent
Check whether the water pressure is too low
Buttons cannot be operated
No water feed or slow water feed
Water leakage occurs at the water tap
Check whether the“child lock”function is activated
Check whether the shape of water tap is suitable
Check whether the water inlet pipe joint is installed in place
Check whether the water tap is damaged
Refer to the instructions under the title of “Cancel or reselect a
program in the process of running” in the sectionof “13.Other
Functions”
When wash
It is normal and the water is the remaining water of factory
inspection
The following phenomena are not necessarily faults of the washer-dryer. Please check against the following
table before call for servicing. If any fault actually exists, please contact our After-sales Service Department
and do not repair by yourself. Please unplug the power plug before check.
2 Precautions for Use
1.Due to the fluctuation of water pressure, please check all the joints of water inlet pipe, water tap and drain
pipe for firm connection before washing every time. In case of loose water pipe connection or water leakage,
please turn off the water tap and take proper measures or contact our After-sales Service Department for
reconnection. Only after such faults are cleared can you use it again.
2.When the washer-dryer is not in use, please keep the door slightly open and towel off both the window
pad and door glass to avoid unpleasant smell. Do not cover the washer-dryer with a plastic bag to avoid
moisture staying in it.
3.Do not place any heavy object, heat-producing appliance and item liable to water/liquid leakage on the
table top to avoid deformation of the tabletop panel and plastic parts.
4.Do not wash such waterproof articles as raincoat, bicycle cover and down products as well as carpet to
avoid abnormal vibration or damage to such articles.
5.Please add a proper amount of washing powder, detergent (or bleach) and softener in corresponding
chambers of the distributor box before starting the selected program. Do not open the distributor box
during the program running to avoid some detergent (or bleach) left in its chamber.
6.If a brassiere with steel wire is washed in the washer-dryer, the steel wire may bounce out. Therefore,
do not wash any brassiere with steel wire in order to protect the washer-dryer.
7.The washer-dryer’s door is equipped with a self-lock safety device. Press the “Start/Pause” button to
make the washer-dryer in pause (if the washer-dryer is operating). Only when the washer-dryer is in the safe
state (the water level is below the lower edge of sight glass, the temperature inside of the drum is below
50 °C and the inner drum is not rotating) and the door lock icon is not illuminated can you open the door by
pressing the door-opening button. Never forcibly open the door before the washer-dryer enters the safe state
8.Turn off the water supply and power supply after finishing washing every time. Meanwhile, clean the sight
glass window pad interlining to prevent contaminants from tainting the clothes again.
9.The washer-dryer described in this manual is equipped with downward drainage system. Please
install the washer-dryer in a location with floor drainer.
10.Using the washer-dryer at or below 0 °C may damage the water inlet valve and drainage system.
If the washer-dryer is stored at or below 0 °C, be sure to move and leave it in the environment at room
temperature for 2-4 hours
before use.
11.Do not put the clothes tainted with chemicals into the washer-dryer.
12.It is prohibited to dry the clothes with oil stains to avoid fire hazard.
13.When any program other than “Supporter Dry” is selected, it is prohibited to put the drying rack into
the washer-dryer to avoid damage to the washer-dryer.
14.When using the washer-dryer’s drawer:
Do not put any flammable, explosive and corrosive substance in the drawer. Do not pour detergent and
washing powder into the drawer to prevent the drawer from being contaminated. The maximum weight
of all the items in the drawer must not exceed 5kg. Please close the drawer immediately after you use it.
Neither should you put wet clothes on the drawer, nor allow the children to play with and step on the drawer
to avoid deformation or damage of the drawer.
to avoid damage to the door or scald.
2

15. When washing small articles (e.g. handkerchiefs, gloves, socks, etc.) and those clothes liable to
inter-twist and wear, please put them in net bags for washing, rinsing and spinning to prevent them from
falling into between the inner drum and window pad and further avoid inadequate washing and drying. The
weight of articles in each net bag must not exceed 300g and the net bags should be put in the washer-dryer
together with those clothes not in a net bag, otherwise the washer-dryer will not be balanced and result in
abnormal vibration. Reference weights for small articles: handkerchiefs about 30g/piece; gloves about
60g/pair; cotton socks about
30g/pair; silk socks about 20g/pair.
16. When spinning at high speed, the clothes will stick on the washer-dryer’s inner drum wall due to
centripetal force. If the clothes are to be dried, it is recommended to take them out and fluff them
out, then put them in the washer-dryer again for drying to achieve optimal drying effect.
17. During heating or drying, high temperature inside the washer-dryer may cause temperature rise of the
tabletop panel and door, etc. Therefore, do not touch the tabletop panel and door during heating or drying.
18. During drying, it is recommended not to load the inner drum with clothes over the height of drying sticker
on the electroplated ring; otherwise inadequate drying may occur.
To clean the drying filter box
Note: Please clean the drying filter box after using the drying function every time.
(1) Pull out the drying filter box as shown in Fig. 1.
(2) Gently open the drying filter box cover as shown in Fig. 2.
(3) Remove the flocking in the drying filter box with a soft bristle brush as shown in Fig. 3.
(4) Close the drying filter box and install it in place.
Fig.1 Fig.2 Fig.3
Note: The flocking must not be piled up around the washer-dryer to avoid its entry into the washer-dryer
and poor drying effect.
To clean the water inlet filter screen
Warm tips: To improve the washing effect, do not
throw away the water inlet filter screen. In case of
unsmooth water feed, please clean the water inlet
filter screen in time as follows:
(1) Screw off the water inlet pipe as shown in Fig.1,
and then take out the filter screen with a pair of
nipper pliers as shown in Fig. 2.
(2) Wash the filter screen with a soft bristle brush.
(3) Install the filter screen in place and connect the
water inlet pipe.
Fig.1 Fig.2
320

14 Cleaning/Maintenance
Please unplug the power plug from the socket before cleaning and maintenance.
After finishing washing, please turn off the water tap and remove the water inlet pipe.
Unplug the power plug and put back the drain pipe.
If the washer-dryer is not to be used for a long time, please keep the door slightly open and dry the
window pad to avoid unpleasant smell.
Do not use organic solvent or corrosive liquid to wipe the washer-dryer’s exterior and rubber parts.
Frequently clean both the water inlet pipe joint and water inlet valve filter screen to prevent them from
being clogged by dirt.
To clean the drain filter (once every 30 days)
After draining the water in the washer-dryer, press the filter cover with a hand to open it as shown in
Fig. 1.
Press the push switch to the end to prevent the hand from being wounded when turning the filter knob,
then anticlockwise screw out the drain filter with a hand.
Note: A little water may flow out when screwing out the filter knob (if Err2 alarm appears, relatively
much water may flow out when screwing out the filter knob). Therefore, prepare a container (e.g. basin)
before screwing out the filter knob and make the water flow in the container but not onto the ground or
floor.
Remove the thrums and impurities on the filter and rinse the filter with clean water.
Insert the filter along the groove and tighten it by turning clockwise; otherwise water leakage may occur.
Be careful not to distort the filter.
Note: The drain filter must be tightened to avoid water leakage.
(5)
Press the push switch again with a hand to make it bounce out, then close the filter cover.
To clean the distributor box
(1) Fully pull out the distributor box.
(2) Slightly lift up and pull out the distributor box.
(3) Rinse the distributor box and siphon cap with clean water.
distributor box.
Note: Please buckle the siphon cap in the correct position of distributor box; otherwise the detergent
and softener in the distributor box cannot be siphoned into the washer-dryer’s drum.
Fig. 1 Fig. 2 Fig. 3
(4) Buckle the siphon cap, then insert, push in and close the
Push
switc
Drain
filter knob
Drain
filter
cover
Loosen
Groove
Drain
filte
r
19 4
(1)

/
(2)
(3)
(4)
3 Components
Main control panel Drying filter box Tabletop pannel
Distributor
box
Electroplated
ring
Door
Drain filter
cover
Front adjusttable foot(2) Drawer Drain pipe joint
Handle (2
on each
side)
Drain pipe
hook (1 on
each side)
Door-opening
button

4 Accessories
Inlet pipe assy (1) Drain pipe assy (1) Drain pipe clamp (1) Drying rack (1)
Packaging bolt cover (4) User manual (1)
5 Notice before Use
Please install and adjust the washer according to the instructions in this manual so that you
can use it in a safe manner.
To connect the water inlet pipe
Please use the new water inlet pipe delivered with the washer-dryer.
(1) Select a proper water tap
In case of unsmooth end face of the water tap outlet,
please file it smooth to avoid water leakage.
(2) Remove the water inlet pipe joint
Press the lower end of locking lever;
Hold the water inlet pipe, press down the slider and
remove the water inlet pipe joint;
Di
i
(1)
Before using, please take out the foam piece between equilibrium wreath and window.
This only is used for transport, so please must take it out with other packing pieces at
the same time.
The lengh of front end must be more than 10mm.
Water inlet pipe joint
Locking lever
Slider
Water inlet pipe
HAIERAPPLIANCES(INDIA)PVT.LTD. (hereinafter referred to as “thecompany”)hereby offers the following warranty to the original
domesticpurchasercommencing from the date of the purchase. The company will, free of charge repair or replace any defective part or
partswhichproveto be defective in workmanship and/or materials and not due to abnormal or improper usage at its sole discretion.
HAIERWARRANTY
CustomerName................................................................Address..............................................................................
SerialNo........................................................Dateofpurchase.........................................Model No..............................
DealerSeal................................................................................................................................................................
1) Thiswarrantywillautomatically terminate on the expiry of the warrantyperiodfromthedate ofdelivery.
2) TheCompanyisnot liable for any delay in servicing due to reasons beyond the control of the Company
oranyofitsauthorisedservice centres.
3) Partsreplacedorrepaired underthis warranty are warranted throughout the remaining of the original
warrantyperiod.
4) Itisentirelyleft to Company’sdiscretion to repair/replace parts at the site of installation or at the
authorisedservicecentreoftheC ompany.
5)Thiswarrantyshallbestrictlylimitedto the repairs or replacement of defective parts specified in the
warranty.Thiswarrantyshallnotcoverany consequential or resulting liability.
6)Thiswarrantyshallnot in any case extend towards payment of any monetary consideration
whatsoeverorreplacementorreturnof the product.
7)TheCompany may repair/supply parts free of cost during the warranty period. This warranty does not
coveranyExciseduty,Centralor Sales tax,octroi and other local taxes or levies on the components/part.
8)Thepartsshallbe replaced by functionally operating equivalent material only and not with brand new
onesandarelikelytobe different from the one originally fitted. The parts thus removed shall be taken
backbythecompany.
9)TheCompany reserves the right to retain any part or component replaced at its sole discretion during the warranty period.
10)In no event the Company or its authorised service centre be liable for any consequential damages or resulting liability, damage or loss arising directly or indirectly out of any defect in
theproduct.
11) Th is warranty is not valid in case of the following events:
a)If the Product has been Installed/Serviced/Repaired/Opened or tampered by any unauthorised personnel.
b)If defects arise/caused by accidents, alteration, misuse, neglect, substitution of original components with spurious/non-genuine components, attacked by household pest/
rodents,fire,flood,earthquake, lightning and/or any other act of God/natural calamities.
c)The product is shifted outside India.
12)For any service under this warranty beyond city/town/municipal limits from the C ompany/authorisedservicecentre,afixedchargeofRs. 50will be collected from the customer in
additiontotheactualtoand fro charges by the shortest route.
13)Anychangeoflocationorchange in the ownership during the warranty period must be intimated in writing to the Company.
14)The C ompany’semployeesoritsauthorisedrepresentativeshaveno authority to vary the terms of this warranty.
15)ThisWarrantyiseffected in New Delhi and claims, if any, shall be made only before the courts having jurisdiction in N ewDelhiandnoclaimshall be made against the company outside
NewDelhinotwithstandingthattheAppliancemay have been sold or delivered elsewhere.
CONDITIONSOF WARRANTY
CustomerName................................................................Address...............................................................................................
SerialNo..........................................................Dateofpurchase.........................................Model No...........................................
DealerSeal...................................................................................................................................................................................
HAIERAPPLIANCES(INDIA)PVT.LTD.B-1/A-14,Mohan Co-operative Industrial Estate,NewDelhi-44
PH:26952470/71/72/73.Fax:[phone]
Product Warranty
Period Partsnot covered
ColourTV12Months Remote,Cabinet
Refrigerator Comprehensive:12Months Plastic,Glassware,
Compressor:60Months LightBulb
Comprehensive:24Months TopLid, Outer Steel
WashingMachine
Motor:60Months Casing
Airconditioner Comprehensive:12Months AirFilter, Front Grill
Compressor:60Months
Microwave 12Months Glass, Plate, Bulb
Dishwasher 24Months
ClothDryer 12Months
DVD12Months
Warranty Card (1) Anti Rat Cover (1) Screw (8)
5
Buzzer mute function
Select the self-clean program, simultaneously press and hold the “Delay”and “Temp.”buttons for 3s to
mute the buzzer for all the programs (excluding the alarm sound), and the display screen will display “bEEP
OFF”. Simultaneously press and hold the “Delay”and “Temp .”buttons for 3s to resume the beep for all the
programs, and the display screen will display “bEEP On”.
Memory program
When selecting the “Memory”program, all the washing parameters set by the user will be memorized
after the program ends. If the user wants to wash with the same settings, just select the “Memory”program
after turning on the washer-dryer.
(This program does not memorize the “delay”function set by the user.)
“Spin” program
Air Wash function
This function is available in the “Dry”mode. The inner drum rotates during air-wash and removes the moisture
and unpleasant smell from the clothes via hot air. Please turn on the water tap before starting air-wash.
Tub Clean function
This function is available in the “Wash”and “Wash & Dry”modes and used to wash away the dirt from inner
and outer drums. Note that clothes must not be put in the washer-dryer when using this function.
The function of drying with rack
This function is used to dry those articles liable to
deformation such as hat, cloth doll and cloth shoes, etc.
Make sure that the articles in the washer-dryer are
suitable for drying with washing machine.
When using the function of drying with rack, put the
drying rack in the drum as shown in Fig. 1. Insert the
protuberance at the front end of drying rack into the hole of inner drum cover, place the back end of drying
rack on the gimbals and keep the drying rack level as shown in Fig. 2.
Fig.1 Fig. 2
To select the “Spin”program only, just anticlockwise ture the program knob
after turning on the washer-dryer by pressing the “On”button.Press the
“Spin”button to set the spinning time; press the “Speed”button to set the
spinning speed.
Gimbals
18

13 Other Functions
Power-down memory
With the power-down memory function, the washer-dryer can memorize the program’s running state
in case of power failure or loose plug during washing and continue the selected program after resuming
the power supply and turning on the washer-dryer by pressing the “On”button.
Cancel or reselect a program in the process of running
If the child lock function is activated, please deactivate it before performing the following operations.
If there is a need to reset the mode (including the “Wash”, “Wash & Dry”and “Dry”modes) and washing
program (e.g. cotton, Synthetics…), gently press and hold the “Off”button for 3s to shut down the
washer-dryer, turn on the washer-dryer again by pressing the “On”button, then reset the desired mode,
washing program and washing parameters.
If only washing parameters (including washing time, times of rinsing, spinning time and spinning speed)
need to be reset, gently press the “Start/Pause”button, then press the “Wash ”, “Rinse”, “Spin”and
“Speed”buttons respectively to set washing parameters, then gently press the “Start/Pause”button
again to start the selected program.
Eccentric protection
When spinning, if the clothes are not evenly distributed, the washer-dryer will fluff out and redistribute the
clothes and continue spinning after the clothes distribution becomes even. If the clothes distribution does not
become even within the specified time, the washer-dryer will not spin to avoid abnormal vibration. In this case,
please check the clothes for intertwist and rearrange them, then select the “spin”program to spin the clothes.
When there are few articles, the washer-dryer may not spin due to eccentric protection. In this case, you can
put more articles in the washer-dryer and make them evenly distributed, then continue spinning. In addition, it
is normal that the program time will prolong for the washer-dryer rearranges and fluffs out the clothes.
Drying
With the function of drying ramie cotton and chemical fiber fabrics, the washer-dryer can automatically
determine the degree of dryness and end the drying program in time. Pay attention to the following when
drying:
Whether the clothes suitable for drying depends on their texture. Make sure that the clothes are suitable
for drying with washing machine before drying.
Before drying, make sure that the water tap is turned on and the water must be cold.
As for the spun clothes, take and fluff them out, and then put them in the drum for drying.
If too many clothes are dried at a time, not only the drying effect is not ideal but also the clothes are
liable to wrinkle. The drying time may be longer than the pre-set time.
The drying time may be shorter than the pre-set time when drying few clothes or light clothes.
It is normal that the drying time may be longer when selecting low-temperature drying program.
Automatic weighing function
In the “Wash”and “Wash/Dry”modes, the “Cotton”, “Memory”, “Synthetics”, “High-Temp”and “Night
Wash”programs all have automatic weighing function.
After setting a program, press the “Start/Pause”button, the drum will start rotating and detecting the
clothes weight. Overweight may be detected in case of wet clothes. In addition, it is normal that low impact
sound may be heard from the washer-dryer.
(3) Install the water inlet pipe joint
Loosen the nut to the extent that approximate 3-4 turns of
screw thread are exposed;
Loosen four screws of the water inlet pipe joint to the extent
that the joint can be ringed onto the water tap;
If the water inlet pipe joint cannot be ringed onto the water
tap, please remove the bushing and install again;
Turn the screw against the wall to an approximately proper
position
in advance, ring the water inlet pipe joint onto the water
tap, then evenly
tighten the remaining three screws in place,
(4) Connect the water inlet pipe
Press down the slider and insert the water pipe into the water inlet
pipe joint;
Hook the water inlet pipe joint with the locking lever, then loosen the
slider until a “poop”is heard. locking lever
(5) Connect to the washer-dryer
Ring the nut at the other end of water inlet pipe onto the water inlet
valve joint;
Tighten and confirm the nut of water inlet pipe in place.
(6) Check the water inlet pipe for good connection
Check for firm connection;
After installation, turn on the water tap and check for water leakage;
Before every use of the washer-dryer, please check for firm
connection between the water inlet pipe and the water tap;
Never forcibly bend the water inlet pipe.
①
②
③
④
①
②
①
②
①
②
③
④
locking lever
Bushing
Tally
Nut
Wall
3-4 turns
If the water tap is placed
against the wall, you may
turn this screw to a proper
positio in advance
and finally tighten the nut.
176

To connect the drain pipe
Ring the drain pipe on the joint;
Fixthe pipe clamp to the groove of drain pipe;
Insert the drain pipe into a floor drainer;
Extend the drain pipe.
State of
extension hose
Height Length
Rise midway Within 10cm
Not rise
midway -
If the drain pipe is too long, remove the pipe sleeve, cut
off the groove part of drain pipe, and then insert the pipe
sleeve into the front end of drain pipe.
If there is a need to extend the drain pipe or change the direction of drain pipe, please contact our
After-sales Service Department.
To remove the packaging
bolts
Packaging bolts are used to fixinternal components of the
washer-dryer during transport and should be removed before
using the washer-dryer.
Screw off all the packaging bolts with a wrench and pull
them out in the direction as shown in the right figure;
Insert the heave of packaging bolt cover into the
packaging bolt cover hole, and then buckle the packaging
bolt cover into the packaging bolt hole in the direction of
arrow as shown in the right figure.
Please keep the dismantled packaging bolts in a safe place
for future handling of
the washer-dryer.
To adjust the front
adjustable foot (2)
Loosen the adjusting nut, and then
adjust the adjustable foot (as shown in
Fig.1) until the air bubble of level gauge
is in the red circle (as shown in Fig. 2).
Tighten the adjusting nut (as shown
in Fig. 3).
Within 3m
Within 1m
Within 10cm
Floor
drainer
Floor
Within 1m
Pipe sleeve
Drain outlet
Stay a space
Groove Pipe sleeve
Before removing the packaging bolts, please fixthe Anti Rat Cover to the bottom of the washer dryer.
Lay down the machine, adjust the Anti Rat Cover with the seven holes corresponding the screw holes.Then
tighten the screws and fixit thus securely to the bottom of the machine.
To install the Anti Rat Cover
Fig. 1 Fig. 2 Fig. 3
Loosen
High
Low Tighten
Adjusting
nut
Adjustable foot
Packaging
bolt hole
Packaging bolt
cover hole
Heave
Pipe clamp
Joint Groove Drain pipe
11 P reparations before Washing
Check the articles to be washed for special washing requirements and make sure that they are
machine washable and dryable to avoid deformation and damage.
For those articles tainted with much mud and dust, please remove them before washing.
Wash those articles liable to color fading separately from others.
Check pockets and remove coins, sand, hairpin and other things from them.
Tie the ties, buckle the buttons, zip the zippers and sew the openings.
To avoid the sound from buttons, please turn those articles with buttons inside out before putting
them in the washer-dryer.
Do not overload the washer-dryer. Furthermore, please unfold and fluff out the articles before
putting them in the washer-dryer.
When washing small articles and those articles liable to inter-twist and wear, please put
them in net bags for washing, rinsing and spinning to avoid damage.
12 Refe rence Weight for Different
Types of Clothing
Asuit of work clothes
Blended fabric,
about 800g
Asuit of pajamas
Cotton, about 300g
Shirt
Blended fabric,
about 200g
Undershirt
Cotton, about 130g
Bath towel
Cotton, about 300g
Briefs
Cotton, about 70g
Socks
Cotton, about 30g
Jeans
Cotton, about 600g
716

15
10 General Program Running
Process
Beating Rolling Soaking
Halfway spinning High-efficiency rinsing
Didtribution Final spinning
Hot air Cold air
Wash
Rinse
SpinDry
The door is automatically unlocked after the program ends.If no button
is pressed within 5mins after the program ends,the washer-dryer will
automatically shut down.
Distributor box
Please select suitable non-foaming or low-foaming washing powder/detergent for automatic drum washer;
As for the dosage of detergent, please refer to the instructions for detergent. Excessive detergent may
result in too many bubbles and spill as well as affect its dissolution;
The level of softener or liquid detergent must not be higher than the “MAX”mark on the siphon cap.
Concentrated softener or liquid detergent should be diluted before being added into the distributor box.
Excessive softener may damage synthetic fiber. As for the dosage of softener, please refer to its instructions.
There may be a
little water in the distributor
boxafter the selected
program ends. It is normal
and the water is the makeup
water or condensate water in
the process of program
running.
Drying filter box
Drawer
Door-opening button
Add solid
washing powder
Add liquid
softener
Add liquid
detergent or
bleach
Siphon cap
The drying filter boxis used to filter the thread
scraps produced in the process of drying.
Be sure to install the drying filter boxin place
before drying; otherwise the washer will alarm
to remind you.
The drawer may be used to store spare
washing powder and detergent, etc.
Do not pour washing powder or detergent into
the drawer to prevent the drawer from being
contaminated.When using the drawer,please
refer to the contents in the section of
“Precautions for Use”.
When the washer-dryer is in the safe state (the
water level is below the lower edge of sight
glass, the temperature inside of the drum is
below 50°Cand the inner drum is not rotating )
and the door is unlocked, the door can be
opened by pressing this button.
8

Press the “ Wash ” button to set
washing time.
Display washing program,
washing time, remaining
time,delay time,times of
rinsing, spinning time,
temperature setting value,
child lock state,door lock
state ,program progress and
alarm message,etc.
After setting relevant parameters,
press the “Start/Pause” button
once, the selected program will
automatically start running. If this
button is pressed when the
program is running,the program
will pause;to continue the
program,just press this button
again.
Note: Washing time doesn’t
include water-feed time and
heating time.
Press the “Rinse”button to select
the times of rinsing and the
maximum allowable times of
running is 8.When the display
screen doesn’t display the times of
rinsing, it indicates that the
washer-dryer will not perform
rinsing.
Press the “Spin” button to select
spinning time. The maximum
allowable spinning time waries with
programs.When the display screen
doesn’t display the spinning time, it
indicates that the washer-dryer will
not perform spinning.
The spinning time means the time
for spinning at high speed.
Press the “Dry” button to select the
“Dry” program.
The “Dry” program is only available
in the “Wash & Dry” and “Dry”
modes.
Press the “Temp.” button to
select the heating temperature
(30, 40, 50, 60, 70, 80 or
90).The maximum allowable
heating temaperature varies
with program.
When the display screen
doesn’t display the
temperature, it indicates that
the washer-dryer will not heat
for washing.
6 Control Panel and Program Description
“Wash” time
Display screen
“Delay” selection “Temp.” selection
“Start/Pause” button
Before starting the selected washing program,press the “Delay” button once and
set the delay time by turnng the program knob. the delay time (0.5-24h) increases
(decreases) with the increment of 30 minutes by clockwise (anticlockwise) turning
the program knob. Press the “Start/Pause” button, the selected program will start
and the delay time will start counting down. After selecting the “Delay” function but
before starting the selected program,press the “Delay” function will be canclled.
The delay time is the end time of washing. For example,6:00 means the washing
ends after 6 hours (if the delay time is shorter than the time required by program
running,the washing program will start running immediately after pressing the
“Start/Pause” to start the “Delay” program).
This function is not available for “Air-wash”,”Drying with rack” and “Self-clean”
program.
9
9 Operational Procedures
14
Place the
drain pipe.
Insert the
power plug
into a power
socket.
Open the door,put
the clothers to be
washed in the
washer-dryer,then
close the door.Add
a proper amount of
detergent in the
distributor box.
Press the
“Strat/Pause”
button to
start the
selected
program.
Select the desired program by turning the
program knob. Select proper washing time,
times of rinsing,spinning time,spinning speed,
the “Dry”program and heating temperature as
required.
Press the “ON”
button to turn
on the washer-dryer.
Select the
desired
mode.
Connect the
water inlet pipe
firmly and turn
on the water
tap.
Times of “Rinse”

13
8 Programs Guide
Program
Cotton
Memory
Synthetics
High Temp
Quick
Night
Wash
Wool
Heavy
Silk
Air wash
Tub
Clean
Supporter
Dry
Recommended Washing
Effectiveness of Washing Programs in Each Mode
“Wash”Mode “Dry”Mode
“Wash & Dry”
Mode
10 8 8
10 8 8
666
10 8
2 2
10 8 8
3
222
3
8
Ĺ
note ĺĺ
For washing and drying ramie cotton fabrics;
default program has the function of automatic
shutdown upon cleanness detected
For washing and drying ramie synthetics
fabrics; default program has the function of
automatic shutdown upon cleanness detected
For washing the washer-dryer’s inner drum;
add a little washing powder or detergent and
do not put clothes in the washer-dryer
For memorizing the program settings
customized by the user
For washing slightly dirty ramie cotton and
chemical fabrics (note ķ)
For washing and drying at night with low
noise
For washing and drying large and heavy
fabrics such as towel quilts (note ĸ)
For sterilization and deodorization of dry
clothes
For drying articles (e.g. cloth doll) liable to
deformation while drying
For washing and drying ramie cotton fabrics
For washing woolen fabrics
For washing silk fabrics
Is
correspond
ing
program
effective
Maximum
capacity of
correspond
ing
program
Is
correspond
ing
program
effective
Maximum
capacity of
correspond
ing
program
Is
correspond
ing
program
effective
Maximum
capacity of
correspond
ing
program
note
note
Note ①:The time displayed on the display screen for quick-wash program does notinclude the time for clothes distribution at the
time of spinning. When selecting the quick-wash program, do not add excessive washing powder, detergent and softener to avoid
inadequate rinsing.
Note ②:The quilts to be washed and dried must be with the machine washable and dryable mark; in addition, the weight must not
exceed 2kg to avoid inadequate washing and drying.
Note ③:The “drying with rack”program is used to dry articles (e.g. hat, cloth doll and cloth shoes) liable to deformation which
must be with the dryable mark. Do not put too many articles in the washer-dryer; otherwise deformation of drying rack and
inadequate drying may occur.
Note ④:Self-clean program is used to clean inner and outer drums. Do not put clothes in the washer-dryer.
Press the “Speed” button to
select spinning speed.The
maximum allowable spinning
speed varies with program.
Three modes (i.e. “Wash”, “Wash & Dry” and “Dry” ) are optional for this
washer-dryer.
Press the desired mode button, corresponding indecator light will be on.
Select the “Wash” mode to wash, rinse and spin the clothes; select the “Wash
& Dry” mode to wash, rinse, spin ahd dry the clothes; select the “Dry” mode to
spin and dry the clothes.
“Speed” selection “Mode” button
“Off”
button
“On”
button Press the “On” button to power on.
When the power is on,press and
hold the “Off” button for 3s to
power off.
If no button is pressed within 5
minutes after power-on or the
autumatic program running ends,
the washer-dryer will automatically
shut down.
Program knob
10
After turning on the washer-dryer,select the desired washing program by turning the knob.Press any function button (e.g. “Speed”, “Temp.”,
“Delay”, “Dry”, “Spin”, “Rinse”, “Wash” button ) once and turn the program knob within 3s to set televant parameters.
After turning on the washer-dryer,the “Spin” program can be selected by anticlockwise turning the program knob.
This washer-dryer is set with the “ ” function.In this mode, turn on the washer-dryer,put the clothes to be washed in it,close the door
and set other relevant parameters,then press the “Start/Pause” button, the display screen will display “ ”; about 2 minutes later, the
washer-dryer will finish weighing and the display screen will display the position of clothes weigh (“ ”~“ ”); and the washer-dryer
will automatically select the optimal washing program.This function allows the washer-dryer to save water,electricity and time significantly.
If you do not want the washer-dryer to weigh the clothes automatically,turn the program knob when the washer-dryer is weighing
automatically and the diaplay screen display “ ” to switch to manual selection of clothes weight position (“ ”, “ ”, “ ”,
“ ”,“ ”). When “ ” displayed on the display screen is flashing,you may select another position by turning the program knob
again within 4s. If you don’t do so within 4s, the program will automatically confirm the “ ” position.
(1) In manual mode, it is recommended that “ ” or “ ” be selected to wash large amount of clothes (more than a half drum);
(2)If the washer-dryer automatically weighs the clothes,it will automatically set the position as“ ”, “ ”, “ ”, “ ”or “ ”.
(3)Please adjust the dosage of washing powder according to the position displayed on the display screen.

7 Display Screen
Washing time (The
time does not
include water-feed
time and heating
time. After the
“Wash”program
ends, this area will
go out.)
Times of
rinsing
(After the
“Rinse”
program
ends, this
area will go
out.)
Spinning time
(After the “Spin”
program ends,
this area will go
out.)
Spinning time
means the time
for spinning at
high speed.
“Dry”program (It is
available in the
“Wash & Dry”and
“Dry”modes.)
Press the “Dry”
button, the program
will switch among
the options listed on
the right:
Normal
Low Temp
Ironing
150min
120min
90min
60min
30min
Heating temperature
(Maximum allowable
heating temperature
varies with programs.
When no temperature
value displays, it
indicates that the
washer-dryer will not
heat.)
Spinning speed
(The setting value of
spinning speed
displays. Maximum
allowable spinning
speed varies with
program.)
After starting the washer-dryer, to prevent
washing process from external interference,
activater the child lock function by
simultaneously pressing and holding the
“Temp.”and “Speed”button for more than 3s; to
deactivate the child lock function, simultaneously
press and hold the same two button for more
than 3s again.
After the child lock is activated, all the function
buttons (escept the “Off”button) are out of
function.
After the program running ends and the
washer-dryer antomatically shuts down, the child
lock function will automatically cancel. If power
failure occure in the process of program running,
the child lock function will not automatically
cancel and must be manually cancelled after
turning on the washer-dryer again.
Washing program (The washer-dryer described in
this manual is set with 12 washing programs. Three
modes i.e. “Wash”, “Wash&Dry”and “Dry”are
corresponding to defferent washing programs.
In the “Wash”mode, Cotton, Memory, Synthetics,
Wool, Silk, Heavy, Quick, Night Wash, High Temp
and Tub Clean program are effective.
In the “Wash & Dry”mode, Cotton, Memory,
Synthetics, Heavy, Quick, Night Wash, High Temp
and Tub Clean program are effective.
In the “Dry”mode, Cotton, Memory, Synthetics, Night
Wash, Heavy, Air Wash and Supporter Dry programs
are effective.)
High
Temp
Caution
Prompt information
(Including:alarm messages
related to Drain Filter, Dry
Filter,Imbalance, High Temp
Caution and Overload.)
It illuminatcs when the “Delay”function is selected.
After selecting the “Delay”function and start the program, the program will analyze
according to the parameter settings and detected clothes weight and may start
running ahead of time. It is normal (for example, if the delay time is set as “”,
press the “Start/Pause”button to start the program, the program will analyze
according to parameters settings and detected clothes weight and may immediately
start running from “”).
It illuminates
when the
washer-dryer
starts without
selecting the
“delay”
function.
Program progress indication area (including four
parts:“Wash”, “Rinse”, “Spin”and “Dry”. When a
program running ends, corresponding word such
as “Wash”in this zone will go out. Full triangles
indecate the program is running.)
Numerical display area (The program with
automatic weighing function) :“ ”diaplays
when the program is not running and in the
process of weighing;remaining time or deplay
time (e.g. “”) diaplays when the program is
running. The program without automatic
weighing fuction:only remaining time or delay
time diaplays. In abnormal conditions, various
alarm codes (e.g. “”) diaplay.
Mark of locking door
(After door locks up, the diagram marks
bright.
Under the safe status and the procedure
being circulated, the mark of locking
door will be put out after pressing
"Start/Pause" , then the door can be
openning pressing the "Open" button.)
Note:The time displayed on the display screen is only for reference and may be slightly different from the
actual time.
Synthetics
Ironing
Heavy
11 12