Haivision Makito Air v2.3 User manual

HVS-ID-QS-MAIR-230, Issue 01 Page 1 of 5
HVS-ID-QS-MAIR-230, Issue 01
Makito Air™v2.3 Quick Start Guide
This Quick Start Guide summarizes the basic steps required to install and configure the Makito Air Ruggedized
HD/SD H.264 Video Encoder (single chassis, as shown below) to stream to your compatible decoding device.
Please refer to the Makito User’s Guide or the online help (available from the Web Interface) for detailed
information.
Installing the Makito Air
1. Unpack the box and visually inspect the package contents for any evidence of shipping damage. [See Impor-
tant Notice for list of contents.]
2. Fasten the Makito Air to a flat surface (such as an equipment bay or rack) using the four (4) threaded
mounting holes (#10-32 screws).
3. Customers are responsible for assembling their own cables. Please refer to “Connector Mapping” on page 5
for connector pinouts.
CAUTION Special care must be taken when wiring the supply. This unit is not protected against polarity
reversal, and if it occurs, the unit will be damaged (servicing will be required). The cabling must be done
in such a way as to maintain the safety, electrical and environmental integrity of the product.
4. Connect the DC input power cable to the power input [J10] at the rear of the unit.
5. Connect the chassis ground wire to the ground lug at the rear of the unit.
Makito Air Rear Panel
Power Input
Chassis Ground

Makito Air Quick Start Guide
Connecting the Makito Air to the Network and A/V Sources
HVS-ID-QS-MAIR-230, Issue 01 Page 2 of 5
Connecting the Makito Air to the Network and A/V Sources
1. Connect the Makito Air’s Ethernet port [J1] to the IP network using a Type Cat 5E cable.
Makito Air Front Panel
2. Connect the Makito Air’s Serial port [J2] to the metadata source using a Serial RS-232 cable.
3. Connect the Makito Air’s SDI Video/Embedded Audio Input [J3] to your Audio/Video sources using the
BNC connector and a coaxial cable.
NOTE: The Makito Air also supports Composite video as well as Analog audio formats. Selection between
Analog (the default) and SDI audio can be done via the Web Interface (ENCODER>AUDIO Settings page).
Setting Up Streaming from the Makito Air
1. Power on the Makito Air.
2. The Makito Air comes pre-configured with the following settings:
* The IP address of your computer must be in the same subnet.
3. To set up a stream to your compatible decoding device, open a Web browser, type the IP Address for the
Makito Air into the URL address bar, and press Enter.
4. Log in to the Makito Air Web Interface, using the following default administrative username and
password: [*Be sure to change the default password!]
IP Address Subnet Mask Gateway
10.5.1.2* 255.255.0.0 10.1.50.1
Admin Username Password
admin manager*
J1: Gigabit
Ethernet port
J2: Serial +J3: SDI + Embedded Audio
Analog Audio InputInput / Composite Video

Makito Air Quick Start Guide
To Modify the Makito Air’s IP Address
HVS-ID-QS-MAIR-230, Issue 01 Page 3 of 5
5. Click SYSTEM from the main menu and then ENCODER>STREAMS from the submenus to open the STREAM
SETTINGS page (shown below).
6. Select TS over UDP for the Stream Type.
7. Type in Multicast Address 225.6.7.8 for the Stream IP.
8. Type in Port # 2000 for the Stream Port.
9. Click Apply.
10. Make sure your decoding device is:
a. supporting UDP Transport Stream format,
b. turned on,
c. connected to a display (if applicable),
d. accessible on the same network segment as the Makito Air, and
e. “tuned” to the Makito Air multicast address (225.6.7.8) / port # (2000).
To Modify the Makito Air’s IP Address
1. Click NETWORK from the main menu to open the NETWORK SETTINGS page (shown on the following page).
Fill in to configure
the first stream instance
Main menu
Submenus

Makito Air Quick Start Guide
For More Information
HVS-ID-QS-MAIR-230, Issue 01 Page 4 of 5
2. Type in the new IP address. If required, select or enter other new value(s) in the appropriate field(s).
3. To save your changes, click Save.
4. To apply your changes, click Reboot. (You must reboot the system for the changes to take effect.)
NOTE You may need to change your computer network settings to be on the same network segment
as the Makito Air.
For More Information
Contact Haivision Technical Support via our Support Portal on our website at: http://support.haivision.com
Or you may use the phone number or email address listed below:
You may download the firmware, Readme file, and PDF versions of the User’s Guide and Quick Start Guide
through our Knowledge Base at: http://www.haivision.com/support/knowledgebase/
North America: Toll Free: 1-877-224-5445
International: Tel: [phone]
Fax: [phone]
Technical Support email: [email protected]
Product Information email: [email protected]
Type in the IP Address

Makito Air Quick Start Guide
Connector Mapping
Connector Mapping
J1 Connector Pinout (Ethernet)
(13 pin female Amphenol MIL-DTL-38999/
20MB35SN)
Pin # Pin Name Type Description
1 ETH_DAP BI 10/100 BASE-T Transmit
differential pair /
Gigabit Ethernet differential pair A
(bi-dir)
2 ETH_DAN BI
3 ETH_DBP BI 10/100 BASE-T Receive
differential pair /
Gigabit Ethernet differential pair B
(bi-dir)
4 ETH_DBN BI
5 ETH_DCP BI 10/100 BASE-T (Unused) /
Gigabit Ethernet differential pair C
(bi-dir)
6 ETH_DCN BI
7 ETH_DDP BI 10/100 BASE-T (Unused) /
Gigabit Ethernet differential pair D
(bi-dir)
8 ETH_DDN BI
9 NC Not Connected
10 NC Not Connected
11 NC Not Connected
12 RESETN IN Hardware Reset (signal is asserted
LOW)
13 GND REF Ground
J3 Connector Pinout (Video Coaxial)
(75-ohm BNC)
Pin # Pin Name Type Description
1 VID IN SDI / Composite video signal
2 VID_GND REF SDI / Composite ground (Cable
shield)
J2 Connector Pinout (Serial Port / Analog Audio)
(13 pin female Amphenol MIL-DTL-38999/
20MB35SA)
Pin # Pin Name Type Description
1 COM_TXDP OUT Serial Interface: RS-232/RS-422
Transmit Data
[only use J2-Pin2 in RS232 mode
(shaded in gray)]
2 COM_TXDN OUT
3 GND REF Shield
4 COM_RXDP IN Serial Interface: RS-232/RS-422
Receive Data
[only use J2-Pin4 in RS232 mode
(shaded in gray)]
5 COM_RXDN IN
6 GND REF Shield
7 AUD_IN_LP IN Analog Audio interface: LEFT
channel differential pair
8 AUD_IN_LN IN
9 AUD_LGND REF Audio Ground
10 AUD_IN_RP IN Analog Audio interface: RIGHT
channel differential pair
11 AUD_IN_RN IN
12 AUD_RGND REF Audio Ground
13 NC Not Connected
J10 Connector Pinout (DC Power)
(5 pin male Amphenol MIL-DTL-38999/
20MB5PN)
Pin # Pin Name Type Description
A PWR_IN REF PSU +28VDC Input
B PWR_GND REF PSU ground return
C NC No connection
D NC No connection
E NC