HAKO Citymaster 1650 Manual

Cleaning technology •Municipal technology
Short instructions for Citymaster 1650
88-10-319-4037-0
Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
A
B
1. Removing the locking shackle Page 84
Caution: Risk of crushing!
Hydraulic oil specification: HVLP 46
Storage location: Bolt A with split pin
3. Checking the engine oil level Page 85
Caution: Risk of scalding!
Engine oil specification: ACEA E6 (Low SAPS)
Note: Switch on the battery isolating switch (optional) B.
2. Checking the fuel supply Page 85
Caution: Risk of fire!
Fuel specification: Diesel (EN 590)
4. Checking the hydraulic oil level Page 85
Caution: Risk of crushing!
Hydraulic oil specification: HVLP 46
Before start-up of the vehicle
Safety information
These short instructions may be used only in conjunction with the original operating manual!
All cross-references refer to the pages in the CM 1650 operating manual.
Please observe the safety information in the operating manual, as from page 11!
Information about special risks, as from page 16! The vehicle may be put into operation only by trained
personnel!

Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
5. Checking the coolant level Page 86
Caution: Risk of scalding!
Coolant specification: ARAL (Aral Antifreeze silicate
free)
7. Checking the windscreen washer unit Page 86
Tank volume: approx. 2 litres
9. Checking the steering column, driver’s seat and
outside mirrors Page 87
Adjust the steering column, driver’s seat and outside
mirrors before driving!
6. Checking the tyre pressure Page 86
Standard tyres 225/70 R15C: front/rear: 5.0 bar
8. Checking the lighting Page 87

Cleaning technology •Municipal technology
Short instructions for Citymaster 1650
88-10-3199-4037-0
Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
1. Preparing for driving Page 88
Move the accelerator pedals 38/39 to the neutral
position.
Actuate the brake pedal 47 or the parking brake 81.
Warning light Alights up. Fasten the seat belt!
3. Starting transport mode Page 90
Release the parking brake 81. Warning light Aoff.
Use the accelerator pedal 38/39 to select the driving
direction.
Working with the vacuum sweeping system
1. Installing the vacuum sweeping system
Page 130
Further installation descriptions for attachments
can be found in the operating manual for the CM 1650.
2. Topping up circulating water D
Page 138
3. Topping up fresh water E
Page 139
2. Starting the engine Page 89
Use the ignition switch 82 to preheat the engine.
Start the engine once the telltale Bgoes out.
Observe the warning symbols! Page 48
4. Parking the vehicle Page 95
Move the accelerator pedal back to the neutral position.
Lock the parking brake 81. Warning light Aon.
Driving with the Citymaster 1650
Safety information
These short instructions may be used only in conjunction with the original operating manual!
All cross-references refer to the pages in the CM 1650 operating manual.
Please observe the safety information in the operating manual, as from page 11!
Information about special risks, as from page 16! The vehicle may be put into operation only by trained
personnel!
47
39
81 82
B
38
C
A
D
E

Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
4. Switching vacuum sweeping on Page 141
Press the Hako button 76. All set sweeping functions
are switched on.
Work mode information symbol Alights up.
6. Starting vacuum sweeping Page 142
Slowly press down the accelerator pedal 38.
Vehicle speed depending on the engine fixed speed:
ECO = 16 km/h, standard = 20 km/h, maximum = 27 km/h
8. Changing the sweeping width Page 143
Press the joystick 74: The left-hand rotating brush
swivels.
Press the joystick 75: The right-hand rotating brush
swivels.
9. Sweeping dry/wet surfaces Page 142
Circulating water is supplied to bind dust.
If necessary, switch on the fresh water pump.
Use the lever Bto adjust the fresh water quantity.
5. Selecting the engine fixed speed Page 142
Tip switch 67 stage 1: ECO – sweeping on the level.
Stage 2: Standard – sweeping on a medium slope.
Stage 3: Maximum – sweeping on a steep slope.
7. Sweeping larger objects Page 143
Press the pedal 48: The coarse material flap opens.
Move the pedal to the right: Pedal engages.
Move the pedal to the left: Pedal disengages.
10. Operating the multifunction display Page 34
The turn-push knob 73 is used to select menus and
submenus and to set values.
Settings during vacuum sweeping:
Setting the rotating brush speed CPage 152
Switching the fresh water pump on DPage 153
Switching the suction fan on EPage 153
76
67
73
74 75
A
38
48
B
C D E