HAKO Citymaster 650 Manual

Cleaning technology •Municipal technology
Short instructions for Citymaster 650
88-10-3208-4001-
Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
1. Removing the locking shackle

Page 80
Caution: Risk of crushing!
Storage location: Bolt A with split pin
3. Checking the engine oil level

Page 80
Caution: Risk of scalding!
Engine oil specification: API CJ-4
e.g.: Titan Cargo 5W-40
2. Checking the fuel supply

Page 80
Caution: Risk of fire!
Fuel specification: Diesel (EN 590)
4. Checking the hydraulic oil level

Page 81
Caution: Risk of crushing!
Hydraulic oil specification: HVLP 46
e.g.: Mobiloil DTE 10 Excel
Before start-up of the vehicle
Safety information
These short instructions may be used only in conjunction with the original operating manual!
All cross-references

refer to the pages in the CM 650 operating manual.
Please observe the safety information in the operating manual, as from page 11!
Information about special risks, as from page 16! The vehicle may be put into operation only by trained
personnel!

Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
5. Checking the coolant level

Page 81
Caution: Risk of scalding!
Coolant specification: G12
e.g.: Total Glaceelf Auto Supra
7. Checking the windscreen washer unit

Page 82
Tank volume: approx. 2 litres
9. Checking the steering column, driver’s seat and
outside mirrors

Page 82
Adjust the steering column, driver’s seat and outside
mirrors before driving!
6. Checking the tyre pressure

Page 81
Standard tyres 23x8.5-12TT 10PR T539:
front/rear: 1.9 bar / 2.7 bar
8. Checking the lighting

Page 82

Cleaning technology •Municipal technology
Short instructions for Citymaster 650
88-10-3208-4001-
Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
1. Preparing for driving

Page 84
Move the accelerator pedals 36/37 to the neutral
position.
Actuate the brake pedal 46 or the parking brake 45.
Warning light A lights up. Fasten the seat belt!
3. Starting transport mode

Page 85
Release the parking brake 45. Warning light A off.
Use the accelerator pedal 36/37 to select the driving
direction.
Working with the vacuum sweeping system
1. Installing the vacuum sweeping system

Page 127
Further installation descriptions for attachments can be
found in the operating manual for the CM 650.
2. Topping up circulating water D

Page 133
3. Topping up fresh water E

Page 133
2. Starting the engine

Page 85
Use the ignition switch 76 to preheat the engine.
Start the engine once the telltale B goes out.
Observe the warning symbols!

Page 49
4. Parking the vehicle

Page 90
Move the accelerator pedal back to the neutral position.
Lock the parking brake 45. Warning light A on.
Driving with the Citymaster 650
Safety information
These short instructions may be used only in conjunction with the original operating manual!
All cross-references refer to the pages in the CM 650 operating manual.
Please observe the safety information in the operating manual, as from page 11!
Information about special risks, as from page 16! The vehicle may be put into operation only by trained
personnel!
46 37 76
B
36
C
A
D
E
45

Hako GmbH - Head Office - Hamburger Str. 209-239 - 23843 Bad Oldesloe, Germany
Tel. [phone] - Fax [phone]
4. Switching vacuum sweeping on

Page 135
Press the Hako button 71. All set sweeping functions
are switched on.
Work mode information symbol A lights up.
6. Starting vacuum sweeping

Page 136
Slowly press down the accelerator pedal 36.
Vehicle speed depending on the engine fixed speed:
ECO = 16 km/h, standard = 20 km/h, maximum = 27 km/h
8. Changing the sweeping width

Page 137
Press the joystick 70 to the left/right:
The rotating brush swivels to the left/right.
9. Sweeping dry/wet surfaces

Page 142
Circulating water is supplied to bind dust.
If necessary, switch on the fresh water pump.
Use the lever B to adjust the fresh water quantity.
5. Selecting the engine fixed speed

Page 136
Tip switch 64 stage 1: ECO – low sweeping power.
Stage 2: Standard – medium sweeping power.
Stage 3: Maximum – high sweeping power.
7. Sweeping larger objects

Page 137
Press the pedal 47: The coarse material flap opens.
Move the pedal to the right: Pedal engages.
Move the pedal to the left: Pedal disengages.
10. Operating the multifunction display

Page 35
The turn-push knob 69 is used to select menus and
submenus and to set values.
Settings during vacuum sweeping:
Setting the rotating brush speed C

Page 141
Switching the fresh water pump on D

Page 142
Switching the suction fan on E

Page 142
71
64
69
70
A
36
47
B
C D E