HAMPTON BAY Garibaldi User manual

Garibaldi
Garibaldi
519 424
524 323

52” Garibaldi
Ceiling Fan by Hampton Bay
40-Watt Intermediate Based
Bulbs Included
3-Speed Reverse Function for
Year-Round Comfort and Savings
Amber Iridescent Glass
Full Function
Remote Control Included
QUESTIONS, PROBLEMS, MISSING PARTS:
Before returning to your local Home Depot, please call our
Customer Service Team at 1-877-527-0313 or visit www.homedepot.com.
Please reference your SKU (519 424 bronze)
or UPC (082392 391102 bronze).
Thank you for purchasing this Hampton Bay ceiling
fan. This product has been manufactured with the
highest standards of safety and quality. The nish
of this fan is weather resistant, but over time will
naturally weather and fade.
Safety Rules ...................................... 1
Unpacking Your Fan........................ 2
Installing Your Fan .......................... 3
Operating Your Fan ......................... 9
Operating Your Remote Control .... 10
Care of Your Fan.............................. 11
Troubleshooting................................ 11
Specications .................................... 12
Warranty Information..................... 13
Table of Contents
UL Model No. 52-GV

Safety Rules ...................................... 1
Unpacking Your Fan........................ 2
Installing Your Fan .......................... 3
Operating Your Fan ......................... 9
Operating Your Remote Control .... 10
Care of Your Fan.............................. 11
Troubleshooting................................ 11
Specications .................................... 12
Warranty Information..................... 13
1. To reduce the risk of electric shock, insure electricity
has been turned off at the circuit breaker or fuse box
before beginning.
2. All wiring must be in accordance with the National
Electrical Code ANSI/NFPA 70-1999 and local electrical
codes. Electrical installation should be performed by a
qualied licensed electrician.
3. WARNING: To reduce the risk of re or electric shock,
this fan should only be used with fan speed control part no.
UC7067RC, manufactured by Rhine Electronic Co., Ltd.
4. CAUTION: To reduce the risk of personal injury, use only
the screws provided with the outlet box.
5. The outlet box and support structure must be securely
mounted and capable of reliably supporting a minimum of
35 pounds. Use only UL Listed outlet boxes marked “FOR
FAN SUPPORT.”
6. The fan must be mounted with a minimum of 7 feet
clearance from the trailing edge of the blades to the oor.
7. Avoid placing objects in path of the blades.
8. To avoid personal injury or damage to the fan and
other items, be cautious when working around or
cleaning the fan.
9. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
10. After making electrical connections, spliced conductors
should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the
grounded conductor and the equipment-grounding
conductor on one side of the outlet box.
11. Electrical diagrams are for reference only. Light kits that are
not packed with the fan must be UL Listed and marked suit-
able for use with the model fan you are installing. Switches
must be UL General Use Switches. Refer to the instructions
packaged with the light kits and switches for proper assembly.
12. All set screws must be checked and retightened where neces-
sary before installation.
Suitable for use with solid-state speed controls.
Safety Rules 1.
READ AND SAVE THESE INSTRUCTIONS
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT WITH THE SCREWS PROVIDED WITH THE OUTLET
BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT
OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT
AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRI-
CIAN IF IN DOUBT.
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE BRACKETS (ALSO REFERRED TO AS “FLANGES”) DURING
ASSEMBLY OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN
THE PATH OF THE BLADES.
TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED
WITH AN ISOLATION WALL CONTROL/SWITCH.

a. Blade attachment hardware
(20 screws)
b. Mounting & Electrical Hardware
(1 hanger pin, 1 locking pin, 3 plastic
wire connectors)
c. Blade Balancing Kit
d. Blade Bracket Hardware
(15 screws and lockwashers)
7. Glass
8. Blade Brackets (5)
9. Bulbs (3)
10. Hand Unit / Receiver
11. Blades (5)
12. Finial
1. Mounting Plate (inside Canopy)
2. Canopy
3. Downrod and Ball Assembly
4. Decorative Motor Collar Cover
5. Fan Motor Assembly
6. Light Kit Assembly
2. Unpacking Your Fan
IMPORTANT: THIS PRODUCT AND/OR COMPONENTS ARE COVERED
BY ONE OR MORE OF THE FOLLOWING U.S. PATENTS: 5,947,436;
5,988,580; 5,971,573; 6,010,306; 6,039,541; 6,046,416 AND OTHER
PATENTS PENDING.
Unpack your fan and check the contents. You should have the following items:
OK
M
d
b
c
a

Installing Your Fan 3.
Tools Required
Phillips screw driver, straight slot screw
driver, adjustable wrench, step ladder, and
wire cutters.
Mounting Options
If there isn’t an existing outlet box, then read
the following instructions. Disconnect the
power by removing fuses or turning off
circuit breakers.
Secure the outlet box directly to the building
structure. Use appropriate fasteners and
building materials. The outlet box and its
support must be able to fully support the
moving weight of the fan (at least 35 lbs.)
Do not use plastic outlet boxes.
Figures 1, 2, and 3 are examples of different
ways to mount the outlet box.
Outlet Box
Note: You may need a longer downrod to
maintain proper blade clearance when install-
ing on a steep, sloped ceiling. The maximum
angle allowable is 30˚. If the canopy touches
downrod, remove the decorative canopy
bottom cover and turn the canopy 180˚ before
attaching the canopy to the mounting plate.
Outlet Box
To hang your fan where there is an existing
xture but no ceiling joist, you may need an
installation hanger bar as shown in Figure 4
(available at your Hampton Bay retailer).
TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR PERSONAL INJURY, MOUNT
FAN ONLY TO AN OUTLET BOX MARKED
ACCEPTABLE FOR FAN SUPPORT AND
USE THE MOUNTING SCREWS PROVIDED
WITH THE OUTLET BOX. OUTLET BOXES
COMMONLY USED FOR THE SUPPORT OF
LIGHTING FIXTURES MAY NOT BE ACCEPT-
ABLE FOR FAN SUPPORT AND MAY NEED TO
BE REPLACED. CONSULT A QUALIFIED ELEC-
TRICIAN IF IN DOUBT.
Figure 1
Figure 2
Figure 4
Figure 3

4.
2. Remove the mounting plate from the cano-
py by loosening the four screws on the top
of the canopy. Remove the two non-slotted
screws and loosen the slotted screws. This
will enable you to remove the mounting
plate (Figure 6).
Hanging the Fan
REMEMBER to turn off the pow-
er. Follow the steps below to hang your
fan properly.
NOTE: This fan is recommended for the
standard ceiling mounting using the downrod
provided with this fan. When using standard
ceiling installation with the 6 inch downrod
provided, the distance from the ceiling to the
bottom of the fan blades will be approximate-
ly 11 inches.
IF YOU FEEL THAT YOU DO NOT
HAVE ENOUGH ELECTRICAL WIRING
KNOWLEDGE OR EXPERIENCE, HAVE
YOUR FAN INSTALLED BY A LICENSED
ELECTRICIAN.
Standard Ceiling Mounting
1. Remove the canopy ring from the canopy
by turning the ring to the right until it un-
locks (Figure 5).
Figure 5
Figure 6
3. Route the wires exiting the top of the fan
motor through the decorative motor collar
cover then the canopy ring. Make sure the
slot openings are on top. Route the wires
through the canopy and then through the
ball/downrod assembly (Figure 7).
4. Loosen, but do not remove, the set screws
on the collar on the top of the motor
housing.
5. Align the holes at the bottom of the down-
rod with holes in the collar on top of the
motor housing (Figure 7). Carefully insert
the hanger pin through the holes in the col-
lar and downrod. Be careful not to jam the
pin against the wiring inside the downrod.
Insert the locking pin through the hole near
the end of hanger pin until it snaps into its
locked position as noted in the circle inset
of Figure 7.
6. Retighten the set screws on the collar on top
of the motor housing.
7. Make sure the grommet is properly installed
in the collar cover, then slide the collar
cover on the downrod until it rests on the
motor housing. Be sure that the canopy and
the collar cover are both oriented correctly.
8. Proceed to “Installing the Fan” section.
FAILURE TO PROPERLY INSTALL THE LOCK-
ING PIN AS NOTED IN STEP 5 COULD RESULT
IN FAN LOOSENING AND POSSIBLY FALLING.
THE FAN MUST BE MOUNTED WITH A MINIMUM
OF 7 FEET CLEARANCE FROM THE TRAILING
EDGE OF THE BLADES TO THE FLOOR.

5.
Figure 7
UL Listed
Outlet Box
Mounting
Screws
(Supplied with
Outlet Box)
Installing Fan to
the Outlet Box
WHEN MOUNTING THE FAN ON A SLOPED
CEILING, THE STANDARD BALL/DOWNROD
MOUNTING METHOD MUST BE USED. THE
MOUNTING PLATE MUST BE MOUNTED SO
THAT THE SLOT OPENINGS ARE ON THE
LOWER SIDE BY SLIDING THE MOUNTING
PLATE FROM THE TOP DOWN.
1. Pass the 120-volt supply wires through the
center hole in the ceiling mounting plate as
shown in Figure 7.
2. Install the ceiling mounting plate on the out-
let box by sliding the mounting plate over
the two screws provided with the outlet box
(Figure 7). If necessary, use leveling wash-
ers (not included) between the mounting
plate and the outlet box. Note that the at
side of the mounting plate is toward the out-
let box (Figure 7).
3. Securely tighten the two mounting screws.
4. Carefully lift the assembly up to the ceiling
mounting plate. Make sure the tab on the
mounting plate socket is properly seated in
the groove in the hanger ball.
Making the Electrical
Connections
REMEMBER to disconnect the power. If
you feel you do not have enough electrical
wiring knowledge or experience, have your fan
installed by a licensed electrician.
Follow the steps below to connect the fan
to your household wiring. Use the wire
connecting nuts supplied with your fan. Se-
cure the connectors with electrical tape.
Make sure there are no loose strands or
connections (Figure 8).
1. Connect both green wires from the down-
rod and mounting plate to the bare copper
(Ground) from the outlet box
2. Connect the black wire (AC IN L) from
the receiver unit to the black wire from the
outlet box.
3. Connect the white wire (AC IN N) from
the receiver unit to the white wire from the
outlet box.
4. Connect the white wire (To Motor N) from
the receiver unit to the white wire from the
fan assembly.
5. Connect the black wire (To Motor L) from
the receiver unit to the black wire from the
fan assembly.

6.
EACH WIRE NUT (WIRE CONNECTOR) SUP-
PLIED WITH THIS FAN IS DESIGNED TO ACCEPT
UP TO ONE 12 GAUGE HOUSE WIRE AND TWO
WIRES FROM THE FAN. IF YOU HAVE LARGER
THAN 12 GAUGE HOUSE WIRING OR MORE
THAN ONE HOUSE WIRE TO CONNECT TO THE
FAN WIRING, CONSULT AN ELECTRICIAN FOR
THE PROPER SIZE WIRE NUTS TO USE.
Figure 8
Finishing the Fan
Installation
STANDARD CEILING MOUNTING
1. Align the locking slots of the ceiling canopy
with the two screws in the mounting plate.
Push up to engage the slots and turn clock-
wise to lock in place. Immediately tighten
the two mounting screws rmly.
2. Install the remaining two mounting
screws into the holes in the canopy and
tighten rmly.
3. Install the decorative canopy ring by
aligning the ring’s slots with the screws in
the canopy. Rotate the ring counter-clock-
wise to lock in place.
4. You may now proceed to attaching the
fan blades.
WHEN USING THE STANDARD BALL/DOWN-
ROD MOUNTING, THE TAB IN THE RING AT
THE BOTTOM OF THE MOUNTING PLATE MUST
REST IN THE GROOVE OF THE HANGER BALL.
FAILURE TO PROPERLY SEAT THE TAB IN THE
GROOVE COULD CAUSE DAMAGE TO WIRING.
6. Connect the blue wire (For Light) from the
receiver unit to the blue wire from the fan.
After wires are connected, carefully tuck them
into the outlet box. Insert the receiver unit into
the mounting plate; make sure the black antenna
wire sits on top of the receiver unit.
THE FREQUENCIES ON YOUR RECEIVER AND
TRANSMITTER HAVE BEEN PRESET AT THE
FACTORY. BEFORE INSTALLING THE RECEIV-
ER, MAKE SURE THE DIP SWITCHES ON THE
RECEIVER AND TRANSMITTER ARE SET TO
THE SAME FREQUENCY. THE DIP SWITCHES
ON THE TRANSMITTER ARE LOCATED INSIDE
THE BATTERY COMPARTMENT.

7.
Attaching the
Fan Blades
1. Attach blade to blade bracket using the
washer head screws provided (Figure 9).
Please note that the rubber washers are pre-
attached to the blade bracket. Start a screw
into the bracket. Repeat for the three re-
maining screws.
2. Tighten each screw securely.
3. Insert the blade assembly through the slot
cut-out in the center ywheel of the fan mo-
tor assembly. Align the three screw holes in
the blade bracket with the screw holes in the
ywheel and secure with screws and lock-
washers provided (Figure 10).
4. Repeat steps 1-4 for the remaining blades.
Figure 9
Center Flywheel
Figure 10
BLADE BALANCING
All blades are grouped by weight. Because nat-
ural woods vary in density, the fan may wobble
even though the blades are weight matched.
The following procedure should correct most
fan wobble. Check after each step.
1. Check that all blade and blade brackets are
secure.
2. Most fan wobble problems are caused when
blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip
of one of the blades. Measure from a point
on the center of each blade to the point on
the ceiling. Measure this distance as shown
in Figure 11. Rotate the fan until the next
Figure 11
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE HOLDERS WHILE
INSTALLING, BALANCING THE BLADES, OR
CLEANING THE FAN. DO NOT INSERT FOREIGN
OBJECTS BETWEEN ROTATING BLADES.
blade is positioned for measurement. Re-
peat for each blade. Measurement devia-
tions should be within 1/8”. Run the fan for
10 minutes.
3. Use the enclosed Bladed Balancing Kit if
the blade wobble is still noticeable.

8.
the switch cup below the fan motor assem-
bly with the black and white wires from the
light kit by connecting the polarized plugs
(blue to black; white to white). Carefully
push all wires back into the switch cup.
3. Align the two key slots in the light kit as-
sembly with the two mounting screws and
lockwashers on the switch cup that were
loosened in step 1, place the light kit as-
sembly over the two screws, turn light kit
assembly clockwise until it locks, tighten
the two screws.
4. Re-install the two mounting screws and
lockwashers that were removed in step 1
and tighten rmly.
5. Remove the nial and hex nut from the
threaded tube, install the threaded tube onto
the stem of the light kit assembly and secure
with hex nut.
6. With power off, install the light bulbs (Max.
40W, provided) into the sockets (Figure 12).
Installing the Light Kit
and Glass Bowl
CAUTION - To reduce the risk of electrical
shock, disconnect the electrical supply circuit
to the fan before installing light kit.
1. Remove two of four mounting screws and
lockwashers on the switch cup below the
fan motor assembly, loosen but do not re-
move the other two mounting screws and
lockwashers (Figure 12).
2. Connect the blue and white wires exiting
Figure 12
OVER LAMPING THE FAN WILL RESULT IN
THE FAN LIGHTS SHUTTING DOWN UNTIL THE
PROPER WATTAGE BULBS ARE INSTALLED.
RESET THE LIGHTS BY TURNING OFF, RE-
PLACE BULBS WITH THE POWER ON.
7. Position the glass bowl over the threaded
tube and secure with nial and nger tight-
en.
NOTE: ALLOW BULBS TO COOL COM-
PLETELY BEFORE TOUCHING OR RE-
PLACING TO AVOID ACCIDENTAL BURN-
ING OF THE SKIN.

Operating Your Fan 9.
The hand unit controls directions
(forward or reverse).
Speed settings for warm or cool weather
depend on factors such as room size, ceil-
ing height, number of fans, and so on.
Warm weather - (Forward) A downward
air ow creates a cooling effect as shown
in Figure 13. This allows you to set your
air conditioner on a higher setting without
affecting your comfort.
Cool weather - (Reverse) An upward air
ow moves warm air off the ceiling are as
shown in Figure 14. This allows you to set
your heating unit on a lower setting with-
out affecting your comfort.
Figure 13
Figure 14

10. Operating Your Remote Control
Setting the Code
This unit has 16 different code combinations. To
set the code, perform the following steps:
A. Setting the code on the transmitter:
a. Remove the battery cover. Press rmly
below arrow and slide battery cover off.
b.Slide code switches to your choice of up
or down position. (Factory setting is all up).
B. Setting the code on the receiver.
a. Slide code switches to the same position
as set on your transmitter.
b.Replace battery cover on transmitter.
CAUTION:
Ceiling angle shall not exceed 30 degrees.
Remote Control Model: UC7067RC Transmitter Operation
NOTE: This remote is equipped with 16 code combinations. To prevent possible interference
from or to other remote units such as garage door openers, car alarm or security system, simply
change the combination code but be sure that the code on both the hand held transmitter and
receiver in the fan are matched.
Install a 9 volt battery (not included).
Operating the Fan:
Hi Key - High Speed Med Key - Medium Speed Low Key - Low Speed
Off Key - Power Off Light Key - Light On/Off Reverse Key - Fan Reversing Function
and Dimmer
Installing Receiver
A. Wire Connection:
Fan Green Wire ............................................................... Bare Supply Wire
Black Receiver Wire (AC IN L) ..................................... Black Supply Wire
White Receiver Wire (AC IN N)..................................... White Supply Wire
White Receiver Wire (TO MOTOR N)........................... White Fan Wire
Black Receiver Wire (TO MOTOR L)............................ Black Fan Wire
Blue Receiver Wire (FOR LIGHT)................................. Blue Light Wire
NOTE: If other fan wires are a different color, have this unit installed by a licensed electrician.
B. Lay the black antenna wire on top of the receiver, and slide the receiver into the mounting
bracket.
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, REMEMBER TO DISCONNECT THE
POWER. DO NOT USE WITH SOLID STATE FANS.
THE ELECTRICAL WIRE MUST MEET ALL LOCAL
AND NATIONAL ELECTRICAL CODE REQUIRE-
MENTS. ELECTRICAL SOURCE AND FANS MUST
BE 115/120 VOLT, 60 HZ . MAXIMUM FAN MOTOR
AMPS: 1.0. MAXIMUM LIGHT WATTS: 300-INCAN-
DESCENT ONLY.

Care of Your Fan & Troubleshooting 11.
Care of Your Fan
Here are some suggestions to help you
maintain your fan.
1. Because of the fan’s natural movement,
some connections may become loose.
Check the support connections, brackets,
and blade attachments twice a year. Make
sure they are secure. (It is not necessary to
remove fan from ceiling.)
2. Clean your fan periodically to help maintain
its new appearance over the years. Do not
use water when cleaning, this could damage
the motor, or the wood or possibly cause
an electrical shock. Use only a soft brush
or lint-free cloth to avoid scratching the
nish. The plating is sealed with a lacquer
to minimize discoloration or tarnishing.
Warning - Make sure the power is off
before cleaning your fan.
3. You can apply a light coat of furniture pol-
ish to the wood for additional protection
and enhanced beauty. Cover small scratches
with a light application of shoe polish.
4. There is no need to oil your fan.
The motor has permanently lubricated
sealed ball bearings. MAKE SURE THE POWER IS OFF AT THE ELECTRICAL PANEL BOX BE-
FORE YOU ATTEMPT TO MAKE ANY REPAIRS. REFER TO THE SECTION,
“MAKING ELECTRICAL CONNECTIONS.”
Fan will not start
Fan sounds noisy
1. Check main and branch circuit fuses or breakers
2. Check line wire connections to the fan and switch wire connections in
the switch housing. CAUTION: Make sure main power is off.
3. Check battery in the transmitter. Does the red LED light come on? Are
you standing close enough to the fan? (Normal range is 10-20 feet.) Are
the dip switch settings the same on the transmitter (hand unit) and re-
ceiver? REMEMBER TO TURN OFF POWER SUPPLY BEFORE
CHECKING THE DIP SWITCH SETTINGS IN RECEIVER.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub
are tight.
3. Make sure wire nut connections are not rattling against each other or
the interior wall of the switch housing. CAUTION: Make sure power
is off.
4. Allow a 24-hour “breaking in” period. Most noises associated with a
new fan disappear during this time.
5. If using the Ceiling Fan light kit, make sure the screws securing the
glassware are tight. Check that the light bulb is also secure.
6. Make sure the canopy is a short distance from the ceiling.
It should not touch the ceiling.
7. Make sure your outlet box is secure and rubber isolator pads were used
between the mounting bracket and outlet box.
Troubleshooting
Problem Solution

12. Specications
These are approximate measures. They do not include Amps and Wattage used by the light kit.
Imported by
Your Other Warehouse LLC
12100 Little Cayman Dr.
Baton Rouge, LA 70809
Vendor number: 219030
FAN SIZE SPEED VOLTS AMPS WATTS RPM CFM NET
WEIGHT
GROSS
WEIGHT
CUBE
FEET
52”
Low 120 0.34 15 65 1895
28.8
Lbs
31.9
Lbs 2.78Med 120 0.46 35 110 3526
High 120 0.60 72 170 5797

Hampton Bay Lifetime Limited Warranty
Lifetime Warranty on Motor
Hampton Bay warrants the fan motor to be free from defects in workmanship and material present at
time of shipment from the factory for a lifetime after the date of purchase by the original purchaser.
Hampton Bay also warrants that all other fan parts, excluding any glass or acrylic blades, to be free
from defects in workmanship and material at the time of shipment from the factory for a period of
one year after the date of purchase by the original purchaser. We agree to correct such defects with-
out charge or at our option replace with a comparable or superior model if the product is returned to
Hampton Bay. To obtain warranty service, you must present a copy of the receipt as proof of pur-
chase. All costs of removing and reinstalling the product are your responsibility. Damage to any part
such as by accident or misuse or improper installation or by afxing any accessories, is not covered
by this warranty. Because of varying climatic conditions, this warranty does not cover any changes
in plated nishes, including rusting, pitting, corroding, tarnishing or peeling. Brass nishes of this
type give their longest useful life when protected from varying weather conditions. Acertain amount
of “wobble” is normal and should not be considered a defect. Servicing performed by unauthorized
persons shall render the warranty invalid. There is no other express warranty. Hampton Bay hereby
disclaims any and all warranties, including but not limited to, those of merchantability and tness
for a particular purpose to the extent permitted by law. The duration of any implied warranty which
cannot be disclaimed is limited to the time period as specied in the express warranty. Some states
do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply
to you. Hampton Bay shall not be liable for incidental, consequential, or special damages arising out
of or in connection with product use or performance except as may otherwise be accorded by law.
Some states do not allow the exclusion of incidental or consequential damages, so the above exclu-
sion or limitation may not apply to you. This warranty gives specic legal rights, and you may also
have other rights which vary from state to state. This warranty supersedes all prior warranties. Ship-
ping costs for any return of product as part of a claim on the warranty must be paid by the customer.
IMPORTANT NOTE:
To ensure warranty service, if ever
necessary, please register your fan at:
gpwarranty.com
You must present a copy of the original
purchase receipt to obtain warranty service.
G.P. WARRANTY SERVICE CENTER, INC.
WARRANTY SECTION
1951 N.W. 22nd STREET
FORT LAUDERDALE, FLORIDA 33311
Attach receipt here for
easy location.
Warranty Information 13.

Garibaldi de 52”
Ventilador de techo de Hampton Bay
Incluye bombillas de base
mediana de hasta 40 Vatios
Función de reversa de 3 velocidades para
confort y ahorro durante todo el año
Vidrio color ámbar iridiscente
Incluye control remoto
con todas las funciones
¿PREGUNTAS, PROBLEMAS O PIEZAS FALTANTES?
Antes de volver a tu tienda local de The Home Depot, llama a nuestro
Equipo de Servicio al Cliente al 1-877-527-0313 o visita www.homedepot.com.
Por favor usa como referencia el Nº de SKU (519 424 bronce)
o UPC (082392 391102 bronce).
Gracias por comprar este ventilador de techo de
Hampton Bay. Este producto se ha fabricado con las
normas de seguridad y calidad más altas. El acabado de
este ventilador es resistente a la intemperie, pero con el
tiempo, exhibirá un desgaste y decoloración naturales.
Normas de seguridad....................... 1
Cómo desempacar el ventilador...... 2
Cómo instalar el ventilador............. 3
Cómo operar el ventilador .............. 9
Cómo manejar el control remoto.... 10
Cuidado del ventilador .................... 11
Solución de problemas..................... 11
Especicaciones................................ 12
Información de la garantía.............. 13
Índice
Modelo de UL Nº 52-GV

1. Para disminuir el riesgo de descarga eléctrica, asegúrate de
que la electricidad ha sido apagada en el cortacircuitos o la
caja de fusibles antes de comenzar la instalación.
2. Todo el cableado debe cumplir con el Código Nacional de
Electricidad ANSI/NFPA 70-1999 y con los códigos locales de
electricidad. La instalación eléctrica debe ser hecha por un
electricista certicado y calicado.
3. ADVERTENCIA: Para disminuir el riesgo de incendio o
descarga eléctrica este ventilador sólo debe ser usado con
un control de velocidad con el N.ode pieza UC7067RC,
fabricado por Rhine Electronic Co., Ltd.
4. PRECAUCIÓN: Para reducir el riesgo de lesiones físicas,
usa sólo los tornillos provistos con la caja eléctrica.
5. La caja eléctrica y estructura de soporte deben montarse
de forma segura y tener capacidad para sostener de manera
conable un mínimo de 35 libras. Usa solamente cajas
eléctricas aprobadas por UL marcadas como “PARA
SOPORTE DE VENTILADOR”.
6. El ventilador debe ir montado con un mínimo de 7 pies de
separación entre el borde trasero de las aspas y el piso.
7. Evita colocar objetos en la trayectoria de las aspas.
8. Para evitar lesiones, o daños al ventilador y otros objetos;
ten cuidado al trabajar cerca del ventilador o al limpiarlo.
9. No usar agua o detergentes para limpiar el ventilador o las
aspas. En general a la hora de limpiar, bastará con usar un
paño seco o ligeramente humedecido.
10. Después de concluir con las conexiones eléctricas, debes
voltear los conductores empalmados hacia arriba y empujarlos
con cuidado hacia dentro de la caja eléctrica. Los cables
deben estar separados, con el cable a tierra y el conductor a
tierra del equipo hacia uno de los lados de la caja eléctrica.
11. Los diagramas eléctricos son sólo una referencia. Los kits de
luces no empaquetados con el ventilador deben estar aprobados
por UL y marcados como apropiados para ser usados con el
modelo de ventilador a instalar. Los interruptores deberán
estar clasicados por el UL como de Uso General. Consulta
las instrucciones adjuntas a los kits de luces e interruptores
para obtener información sobre el ensamblaje adecuado.
12. Todos los tornillos colocados se deben vericar y ajustar donde
sea necesario antes de la instalación.
Puede usarlo con un dispositivo de control de velocidad de
estado sólido.
1. Normas de seguridad
LEE LAS INSTRUCCIONES Y GUÁRDALAS
PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA
O LESIONES PERSONALES, MONTA EL VENTILADOR SOBRE UNA
CAJA ELÉCTRICA MARCADA COMO APROBADA COMO SOPORTE DE
VENTILADOR Y USA TORNILLOS DE MONTAJE QUE VIENEN CON LA
MISMA. LAS CAJAS ELÉCTRICAS UTILIZADAS COMÚNMENTE PARA
EL SOPORTE DE ARTÍCULOS DE ILUMINACIÓN PUEDEN NO SERVIR
COMO SOPORTE DE VENTILADOR, Y TAL VEZ DEBAN REEMPLAZARSE.
EN CASO DE DUDA, CONSULTA A UN ELECTRICISTA CALIFICADO.
PARA REDUCIR EL RIESGO DE LESIONES PERSONALES, NO DOBLAR
LOS BRAZOS DE LAS ASPAS (TAMBIÉN LLAMADOS “REBORDES”)
DURANTE O DESPUÉS DE LA INSTALACIÓN. EVITA COLOCAR
OBJETOS EN LA TRAYECTORIA DE LAS ASPAS.
PARA EVITAR EL RIESGO DE DESCARGA ELÉCTRICA, ESTE
VENTILADOR DEBE SER INSTALADO CON UN CONTROL/
INTERRUPTOR DE AISLAMIENTO DE MONTAJE EN PARED.

a. Herrajes de montaje de aspas
(20 tornillos)
b. Herrajes de montaje y electricidad
(1 pasador de soporte, 1 pasador de cierre,
3 conectores plásticos de cable)
c. Kit de compensación de aspas
d. Herrajes de soporte del aspa
(15 tornillos y arandelas de seguridad)
7. Vidrio
8. Soportes del aspa (5)
9. Bombillas (3)
10. Unidad de mano/receptor
11. Aspas (5)
12. Remate
1. Placa de montaje (dentro de la cubierta)
2. Cubierta
3. Ensamblado de tubo bajante y bola
4. Cubierta decorativa del collarín del motor
5. Ensamblado del motor del ventilador
6. Ensamblado del kit de luces
Cómo desempacar el ventilador 2.
IMPORTANTE: ESTE PRODUCTO Y/O SUS COMPONENTES ESTÁN
PROTEGIDOSPORUNAOMÁSDELASSIGUIENTESPATENTESDEEE.UU.:
5,947,436;5,988,580;5,971, 573;6,010,306;6,039,541;6,046,416yOTRAS
PATENTES PENDIENTES.
Desempaca tu ventilador y revisa el contenido. Deberá tener las siguientes piezas:
OK
M
d
b
c
a

3. Cómo instalar el ventilador
Herramientas necesarias
Destornillador Phillips, destornillador plano,
llave ajustable, escalera de tijera y cortacables.
Opciones de montaje
Si no hay una caja eléctrica existente, entonces
lee las siguientes instrucciones. Desconecta
la energía retirando los fusibles o apagando
los cortacircuitos.
Asegura la caja eléctrica directamente a la
estructura del edicio. Usa sujetadores y
materiales de construcción apropiados. La
caja eléctrica y su soporte deben sostener
completamente el peso en movimiento
del ventilador (al menos 35 libras).
No uses cajas eléctricas de plástico.
Las guras 1, 2 y 3 son ejemplos de diferentes
formas de montar la caja eléctrica.
Caja eléctrica
Caja
eléctrica
Nota:Talveznecesites un tubobajantemás largo
para mantener la altura mínima adecuada de
las aspas al instalar el ventilador en un techo
inclinado. El ángulo máximo permitido es
de 30º. Si la cubierta toca el tubo bajante,
retira la cubierta inferior decorativa
y gira la cubierta 180º antes de jar la
cubierta a la placa de montaje.
Para colgar tu ventilador donde haya una
lámpara pero ninguna viga de techo, tal vez
necesites una barra colgante de instalación
como se muestra en la Figura 4 (disponible en
la tienda minorista local de Hampton Bay).
PARA REDUCIR EL RIESGO DE INCENDIO,
DESCARGA ELÉCTRICA O LESIONES
PERSONALES, MONTA EL VENTILADOR SÓLO
SOBRE UNA CAJA ELÉCTRICA MARCADA
COMO APROBADA COMO SOPORTE DE
VENTILADOR Y USA LOS TORNILLOS DE
MONTAJE QUE VIENEN CON LA MISMA.
LAS CAJAS ELÉCTRICAS UTILIZADAS
COMÚNMENTE PARA EL SOPORTE DE
ARTÍCULOS DE ILUMINACIÓN PUEDEN NO
SERVIR COMO SOPORTE DE VENTILADOR, Y
TAL VEZ DEBAN REEMPLAZARSE. EN CASO
DE DUDA, CONSULTA A UN ELECTRICISTA
CALIFICADO.
Figura 1
Figura 2
Caja eléctrica
Figura 4
Soporte
fuerte
Placa
de montaje
en el techo
Caja
eléctrica
empotrada
Figura 3

4.
2. Retira la placa de montaje de la cubierta
aojando los cuatro tornillos de la parte
superior de la misma. Quita los dos tornillos
sin ranura y aoja los tornillos ranurados.
Esto te permitirá retirar la placa de montaje
(Figura 6).
Cómo colgar el ventilador
RECUERDA desconectar la corriente.
Sigue estos pasos para colgar correctamente tu
ventilador.
NOTA: Se recomienda instalar este ventilador
en un techo estándar usando el tubo bajante
suministrado con el ventilador. Cuando uses
una instalación de techo estándar con el
tubo bajante de 6 pulgadas suministrado, la
distancia desde el techo a la parte inferior de las
aspas será de 11 pulgadas aproximadamente.
Gira el aro en la cubierta para quitarla
Figura 5
Quitar
Aflojar pero no retirar
Figura 6
SI NO INSTALAS CORRECTAMENTE EL
PASADOR DE CIERRE SEGÚN LO INDICADO
EN EL PASO 5 SE PUEDE AFLOJAR Y
POSIBLEMENTE SE CAIGA EL VENTILADOR.
ESTE VENTILADOR DEBE IR MONTADO CON
UN MÍNIMO DE 7 PIES DE SEPARACIÓN ENTRE
EL BORDE TRASERO DE LAS ASPAS Y EL PISO.
3. Inserta los cables que salen por la parte superior
del motor del ventilador, primero, a través de
la cubierta decorativa del collarín del motor y
luego, por el aro de la cubierta. Asegúrate de
que las aberturas en forma de ranura estén en
la parte superior. Inserta los cables a través de
la cubierta y luego a través del ensamblado del
tubo bajante y la bola (Figura 7).
4. Aoja, sin quitarlos, los tornillos en el
collarín ubicado en la parte superior de la
carcasa de motor.
5. Alinea los oricios en la parte inferior del
tubo bajante con los oricios en el collarín
de la parte superior de la carcasa de motor
(Figura 7). Inserta con cuidado el pasador
de soporte a través de los oricios del
collarín y del tubo bajante. Ten cuidado de
no apretarlo contra el cableado dentro del
tubo bajante. Inserta el pasador de cierre en
el oricio cercano al extremo del pasador
de soporte hasta que quede encajado en su
posición como se muestra en el círculo de
la Figura 7.
6. Vuelve a ajustar los tornillos del collarín en
la parte superior de la carcasa del motor
7. Asegúrate de que el ojal esté instalado
correctamente en la cubierta del collarín, luego
desliza la cubierta del collarín por el tubo
bajante hasta que quede en la carcasa del motor.
Asegúrate de que la cubierta y la cubierta del
collarín tengan la orientación apropiada.
8. Sigue con la sección "Cómo instalar el
ventilador".
SI CREES QUE NO TIENES SUFICIENTE
EXPERIENCIA O CONOCIMIENTOS EN
CABLEADO ELÉCTRICO, CONTRATA A
UN ELECTRICISTA CON LICENCIA PARA
QUE INSTALE EL VENTILADOR.
Montaje de techo estándar
1. Retira el aro en la cubierta, girando el aro
a la derecha hasta destrabarlo (Figura 5).