Hans Grohe 28110XX1 User manual

Raindance Allrounder
28110XX1
Wall Outlet Adapter with Hose
Connection
28108XX1
Installation Instructions / Warranty

2
Raindance Allrounder
28110XX1
Technical Data
Max. flow rate of showerhead 2.5 gpm
Determining the mounting height (X)
The Allrounder should be mounted according to the preferences of the users. It should be conve-
nient for all adult users.

3
Install the Allrounder with the Optional Wall Outlet
Adapter with Hose Connection 28108XX1
Roughing in
If you are not using the 28108XX1 wall outlet adapter, go to page 9.
Install a properly anchored 1/2" NPT drop-eared ell, at
least 2" behind the surface of the finished wall. Install a
test nipple in the ell.
When the finished wall is complete, mark the test nipple at
the wall surface. Remove the test nipple.
Measure the test nipple to the mark.
Subtract 3/8" from this measurement. This is the length
of the brass nipple required to install the wall outlet
adapter.

4
Installation
Wrap both ends of the brass nipple with Teflon tape.
Screw it into the mounting piece.
Screw the test nipple / mounting piece assembly into the
drop-eared ell.
Tighten with a 12 mm Allen wrench (not included).
Position the mounting plate over the mounting piece.
Use a grease pencil or similar tool to mark the position
of the screw holes.
Seal the wall around the mounting piece with water-
proof sealant.
Do not overtighten, or damage will
result.

5
Drill the holes with a 6 mm bit. Use extreme caution
- do not drill into the water line.
Install the anchors.
Remove the long bottom mounting screw on the All-
rounder. Replace with the shorter screw included with
the adapter.
Seal the wall around the anchors
with waterproof sealant.
Failure to seal the wall can lead
to possible water damage.
Install the mounting plate, using the screws and offset
bushings provided.

6
Slide the handshower into the handshower holder.
Guide the hose over the hose hook.
Install the handshower
Place a black rubber washer in one end of the hose.
Screw this end to the wall outlet adapter.
Place the screen washer in the other end of the hose.
Screw this end to the handshower.
Attach the Allrounder to the mounting plate. Tighten the
set screw.

7
Replacement Parts
28108001
1 check valve 94074000
2 screw 97598000
Check Valve Maintenance: Backflow preven-
tion is provided by a check valve, which is integral
to the wall outlet adapter. The check valve should be
removed and cleaned yearly.
1
2

8
Corner Mount Kit 28105XX0
Note: The corner mount kit is
not for use with the 28108XX1
wall outlet adapter.
Position the corner mount against the wall at the
desired location.
Mark the positions of the screw holes.
Put the mount aside.
Drill the holes using a 6 mm bit.
Seal the wall around the anchors
with waterproof sealant.
Failure to seal the wall can lead
to possible water damage.
Install the corner mount with the screws and offset
bushings.
Install the Allrounder (see page 10). Tighten the set
screw.

9
Install the 28110XX1 Allrounder
Do not drill through the mounting plate.
Put the mounting plate away in a safe location.
Drill the holes, using a 6 mm bit.
Place the mounting plate against the wall at the de-
sired location. Mark the locations of the screw holes.

10
Place the Allrounder over the mounting bracket (1).
Tighten the set screw (2).
Install the handshower:
Place a black rubber washer in one end of the hose.
Connect this end of the hose to the wall outlet (not
included).
Place the screen washer in the other end of the hose.
Screw it to the handshower.
Install the anchors.
Seal the wall around the anchors
with waterproof sealant.
Failure to seal the wall can lead
to possible water damage.
Secure the mounting plate to the wall with the screws
and the offset bushings. The set screw should be on
top.