Hans Grohe AXOR 250 / 580 3jet 35283007 Manual

ZH 用户手册/组装说明 2
EN Instructions for use / assembly instructions 3
250 / 580 3jet
35283007

问题 原因 补救
花洒头严重泄露 -花洒头脏污/产生钙质垢 -清洁花洒头/去除钙质垢
参见第页8
安装 参见第页 6
清洗 (参见第页8)并附有小手册
排水口
排水功率必须大于50l/min。
该区域需要一个加固边壁。
冷水
热水
安装示意 (参见第页4)
流量示意图 (参见第页4)
大小 (参见第页7)
请勿使用含有乙酸的硅胶！
符号说明
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
头顶花洒夹持杆只为夹持头顶花洒而设计，不得让其承载其它物品！
不得让儿童和肢体、精神和/或意识有障碍的成人在不受监管的情况下
使用淋浴系统。受酒精或毒品影响的人员不得使用淋浴系统。
必须避免让身体敏感部位（如眼睛）接触到莲蓬头喷水。必须保持莲蓬
头与人头之间有足够的距离。
本产品只允许作为洗浴、卫生和洁身之用。
安装提示
• 安装前必须检查产品是否受到运输损害。安装后将不认可运输损害或表
面损伤。
• 管道和阀门必须根据通用标准进行安装、冲洗和检查。
• 请遵守当地国家现行的安装规定。
• 在安装产品的位置，安装人员必须确保安装面的墙面是平的（没有突出
物或瓷砖没有突起），墙体结构适合产品的安装并没有弱点。包装内的
膨胀螺丝只适用于混凝土墙体。对于其他墙体结构必须咨询膨胀螺丝生
产商的建议。
• 必须安装接污滤网，以免从管网中冲入污物。一旦污物冲入，将会有碍
功能和/或导致阀门功能部件的损坏，由此而产生的各种损害汉斯格雅
公司将不承担责任。
• 本产品并非设计来与蒸气浴连接使用！
技术参数
工作压强： 最大0,6MPa
推荐工作压强： 0,2-0,4MPa
(1MPa=10bar=147PSI)
热水温度： 最大60°C
推荐热水温度： 42°C
热力消毒 最大70°C/4分钟
该产品不可与液控和热控即热式热水器连接使用。
该产品专为饮用水设计！
中文
配戴保护手套
配戴护眼用具
柔软剂 (柠檬酸)
避免眼睛和皮肤接触。如该产品不慎进入眼睛，立即
用清水彻底冲洗。
天然海绵
备用零件(参见第页12)
2
> 50 l/min
Raindrain

Fault Cause Remedy
Head shower extremely leaky - Head shower soiled / scaled - Clean / descale head shower
see page 8
Assembly see page 6
Cleaning (see page 8) and enclosed brochure
Waste
The waste drain performance must be more than 50 l/min.
The wall must be reinforced in this area.
Cold water
Warm water
Installation example (see page 4)
Flow diagram (see page 4)
Dimensions (see page 7)
Do not use silicone containing acetic acid!
Symbol description
Safety Notes
Gloves should be worn during installation to prevent crushing and cutting
injuries.
The arm of the shower head is intended only to hold the shower head. Do not
load it down with other objects!
Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the influ-
ence of alcohol or drugs are prohibited from using this product.
Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
The product may only be used for bathing, hygienic and body cleaning pur-
poses.
Installation Instructions
• Prior to installation, inspect the product for transport damages. After it has been
installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the applica-
ble standards.
• The plumbing codes applicable in the respective countries must be observed.
• Where the contractor mounts the product, he should ensure that the entire area of
the wall to which the mounting plate is to be fitted, is flat (no projecting joints or
tiles sticking out), that the structure of the wall is suitable for the installation of the
product and has no weak points. The enclosed screws and dowels are only suit-
able for concrete. For another wall constructions the manufacturer's indications of
the dowel manufacturer have to be taken into account.
• The mesh washers must be installed to protect against incoming dirt by pipework.
Incoming dirt can impair the function and/or lead to damages on functional
parts of the fixture; Hansgrohe will not be held liable for resulting damages.
• The product is not designed to be used with steam baths!
Technical Data
Operating pressure: max. 0,6 MPa
Recommended operating pressure: 0,2 - 0,4 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Recommended hot water temp.: 42°C
Thermal disinfection max. 70°C / 4 min
This mixer cannot be used in conjunction with hydraulically, electronically or ther-
mally controlled instantaneous heaters.
The product is exclusively designed for drinking water!
English
Safety gloves must be worn
Eye protection must be worn
Decalcifier (Citric acid base)
Avoid contact with eyes and skin. If this product contacts
your eyes, rinse thorougly with water.
natural sponge
Spare parts(see page 12)
3
> 50 l/min
Raindrain

4
2200
800
2400
450
60
4,5
0,0
0,5
1,0
1,5
2,0
2,5
3,0
3,5
4,0
5,0
bar
0,45
0,00
0,05
0,10
0,15
0,20
0,25
0,30
0,35
0,40
0,50
036912151821242730
MPa
00,1 0,2 0,3 0,4 0,5
Q = l/min
Q = l/sec
250 / 580 3jet
1 = Rain
2 = Rainflow
3 = Mono
4
Montagebeispiele

5
DN 20
(3/4“)
DN 20
(3/4“)
DN 15
(1/2“)
DN 15
(1/2“)
DN 15
(1/2“)
DN 20
(3/4“)
DN 70
Raindrain
60067000
> 50 l/min
36884000+
01800187
36716000+
01800187
Rainflow
Rain Mono
iBox universal
01800187
DN 20
(3/4")

6
16x2
18x2
1.
2.
2
4
1
3
2. 2.
1.
iBox universal
01800187
SW 2 mm
(2 Nm)
SW 4 mm
(5 Nm)
2.
1.
3.
Nr. 10476220
Armaturenfett
Grease
Montage

7
586
6
160
27
37
91°
354
68
45
128
258
350
600
100 - 600
350
68
800
Maße
250 / 580 3jet
35283007

8
中文 English
Cleaning Recommendation for Hansgrohe Products
Today, modern sanitary and kitchen tapware, showers, accessories, washstands,
tubs and radiators consist of very different materials to comply with the needs of the
market with regard to design and functionality.
To avoid damage and reclamations, it is necessary to consider certain criteria when
cleaning.
With regard to caring for the Hansgrohe products, the
following must in principle be heeded:
• Only use cleaning material which is explicitly provided for this type of
application.
• Never use cleaning materials, which contain hydrochloric acid, formic acid,
chlorine pale lye or acetic acid, as they cause considerable damage.
• Phosphorus acidic cleaners are only conditionally applicable.
• Mixing cleaning agents is not permitted, generally.
• Never use cleaning materials or appliances with an abrasive effect, such as
unsuitable cleaning powders, sponge pads or micro fibre cloths.
• The instructions of the cleaning agent manufacturers have to be followed
absolutely.
• Cleaning has to be carried out with a specified cleaner dosage, contact time,
object-related and adapted to the needs.
• The building up of calcifications has to be removed by cleaning regulary.
• When using spray cleaners, spray the cleaning solution onto a soft cloth or
sponge, never directly onto the Hansgrohe products, as the atomised spray could
enter openings and gaps in the Hansgrohe products and cause damage.
• After cleaning rinse thoroughly with clean water to remove any cleaner residue.
• The use of steam cleaners is not permitted. The high temperatures can damage
the products.
Important
Residues of toiletries such as liquid soaps, shampoos and shower gels, hair dyes,
perfumes, aftershave and nail varnish can also cause damage.
Here too: Carefully rinse with water after use to remove residues.
Likewise, do not store any cleaning agents or chemicals under the products, for
example in a vanity unit, as the vapours may damage the products.
The damage of already damaged surfaces will deteriorate under the effect of the
cleansers.
Components with damaged surfaces must be exchanged,
otherwise there could be an injury danger.
Damage caused by improper treatment will not be covered by our guarantee.
QuickClean
The QuickClean cleaning function only needs a small manual rub over to remove
the lime scale from the spray channels.
Warranty
Hansgrohe guarantees to the consumer that this product is free of production
faults. If evertheless any defect is detected within 5 years from date of purchase,
Hansgrohe will remedy this defect free of charge. You will find the conditions and
details of this guarantee at www.hansgrohe-int.com/guarantee. Please contact your
contracting party to claim your rights under this guarantee. This guarantee does not
affect the customer‘s rights under the respective national legislation.
汉斯格雅产品的清洁建议
现代的卫浴龙头、厨房龙头、花洒、配件、盥洗台、浴盆和加热器采用的
制造材料非常迥异，以适应产品外形设计和使用功能的市场需求。
为了避免产品损坏和由此引发的投诉及争议，必须在使用和清洁产品时遵
循有关规程。
在保养汉斯格雅产品时，原则上必须注意：
• 只能使用那些有明确注明是适用于本产品的清洁剂。
• 不允许使用含有盐酸、蚁酸、氯漂或醋酸的清洁剂，因为这些清洁剂会
给产品表面造成严重的损伤。
• 含磷酸的清洁剂必须在特定条件下使用。
• 不允许将两种以上清洁剂混合使用。
• 不允许使用具有研磨作用的清洁工具和设备，如不适合的清洁粉末、海
绵垫或超细麦克布。
• 必须严格遵守清洁剂生产厂商的使用说明。
• 严格遵守清洁剂的用量和作用时间，决不允许清洁剂的作用时间长于规
定值。
• 定期的清洁以预防水垢。
• 不允许将清洁剂直接喷射到汉斯格雅产品上，因为喷雾会进入汉斯格雅
产品的开口部分和缝隙中而造成损害。首先将清洁剂喷在软布上，再用
软布进行清洁。
• 清洁之后必须用足够的清水冲洗，以彻底去除残留的吸附物（清洁剂）
。
• 不允许使用蒸汽清洗机，高温会损害产品。
重要说明
肥皂，洗发水、沐浴液、染发剂、香水、刮胡水、指甲油的残留也会对产
品造成损伤。
此处：使用后要小心地用清水将剩余物冲洗干净。
同样在产品下方不得存放洗涤剂和化学药品，例如不可放在用于洗脸盆的
梳洗柜中否则挥发气体将损坏产品。
在已经损伤的表面继续使用清洁剂会给表面造成更大的损伤。
表面损坏的部件必须更换，否则会有受伤的危险。
不按规定进行清洁而造成的任何损坏不在本公司产品保修范围之内。
QuickClean
有了QuickClean，手工清洁功能，要去掉喷头上的水垢，只需简单地搓除
即可。
担保
Hansgrohe向用户保证，该产品无制造缺陷。如果自购买之日起五年内出
现缺陷，Hansgrohe将免费排除。保证条件和详情见www.hansgrohe-int.
com/guarantee。在提出保修的权利时请联系您的合同方。本保证不涉及
有关国家法律规定的消费权
QUICK
CLEAN

9
A B
E F
C D
2.
3.
1.
Reinigung

10
SW 4 mm
2.
SW 2 mm
1.
1 2
3 4
5 6
4x
92686000 92686000
92686000

11
16x2
18x2
SW 4 mm
(5 Nm)
Nr. 10476220
Armaturenfett
Grease
1.
SW 2 mm
(2 Nm)
3.
7 8
910
11
(0,5 Nm)
2.
2.
2.
1.
1.

12
Serviceteile
250 / 580 3jet
35283007
Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach · Telefon [phone] · Telefax +49 (0) 7836/511440
E-Mail: [email protected] · Internet: www.hansgrohe.com
07/2017 9.05832.51
98181000
(18x2)
98513000
98214000
(12x2)
96525000
(M520)
97669000
(M48)
98133000
(16x2)
95170000
13595000
(25 mm)
95521000
(1°)
98133000
(16x2)
92748000
92746000
98205000
(21x2)
92686000
92684000
92683000
98163000
(15x2)
98388000
(24x2)
92747000
95659000