Hans Grohe AXOR Montreux 16553007 Manual

INSTALLATION
ZH ⁄ 用户手册 ⁄ 组装说明 02
EN ⁄ Instructions for use ⁄ Assembly instructions 03
Lesezeichen
中文 02
English 03
AXOR Montreux
16553007

02
安装 (参见第页 04)
ZH
安全技巧
装配时为避免挤压和切割受伤，必须戴上手套。
本产品只允许作为洗浴、卫生和洁身之用。
冷热水管间过大的压力差必须予以平衡。
安装提示
⁄ 安装前必须检查产品是否受到运输损害。 安装后
将不认可运输损害或表面损伤。
⁄ 管道和阀门必须根据通用标准进行安装、冲洗和
检查。
⁄ 请遵守当地国家现行的安装规定。
技术参数
本龙头配有 EcoSmart® (流量限制器)
工作压强： 最大 1 MPa
推荐工作压强： 0,1 - 0,5 MPa
测试压强： 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
热水温度： 最大 60°C
热力消毒: 70°C ⁄ 4 分钟
⁄ 该产品专为饮用水设计！
⁄ 自动防止回流
符号说明
请勿使用含有乙酸的硅胶！
热表面！
大小 (参见第页 08)
流量示意图 (参见第页 08)
保养 (参见第页 09)
单向阀必须在符合国家或当地的法律的情况
下按照EN 806-5定期检查 (至少一年一次) 。
备用零件 (参见第页 13 )
清洗 (参见第页 10)
操作 (参见第页 07)
问题 原因 补救
⁄龙头出水量小 ⁄ 单向阀装反 ⁄ 正确安装单向阀
⁄ 花洒滤网有垃圾堵塞 ⁄ 清洗花洒和软管间的过滤网
⁄燃气热水器不工作 ⁄ 手持花洒的流量限制器没有去除 ⁄ 去除流量限制器
⁄ 花洒滤网有垃圾堵塞 ⁄ 清洗花洒和软管间的过滤网
⁄ 单向阀装反 ⁄ 正确安装单向阀

03
ASSEMBLY (see page 04 )
EN
SAFETY NOTES
Gloves should be worn during installation to prevent
crushing and cutting injuries.
The product may only be used for bathing, hygienic
and body cleaning purposes.
The hot and cold supplies must be of equal pressures.
INSTALLATION INSTRUCTIONS
⁄ Prior to installation, inspect the product for transport
damages. After it has been installed, no transport or
surface damage will be honoured.
⁄ The pipes and the fixture must be installed, flushed and
tested as per the applicable standards.
⁄ The plumbing codes applicable in the respective
countries must be observed.
TECHNICAL DATA
This mixer series-produced with EcoSmart® (flow limiter)
Operating pressure: max. 1 MPa
Recommended operating pressure: 0,1 - 0,5 MPa
Test pressure: 1,6 MPa
(1 MPa = 10 bar = 147 PSI)
Hot water temperature: max. 60°C
Thermal disinfection: 70°C ⁄ 4 min
⁄ The product is exclusively designed for drinking water!
⁄ Safety against backflow
SYMBOL DESCRIPTION
Do not use silicone containing acetic acid!
Hot surface!
DIMENSIONS (see page 08)
FLOW DIAGRAM (see page 08 )
MAINTENANCE (see page 09)
The check valves must be checked regularly
according to EN 806-5 in accordance with
national or regional regulations (at least once a
year).
SPARE PARTS (see page 13 )
CLEANING (see page 10 )
OPERATION (see page 07)
FAULT CAUSE REMEDY
⁄ Insufficient water ⁄ check valve hasn't moved back ⁄ Exchange check valves
⁄ Shower filter seal dirty ⁄ Clean filter seal between shower and
hose
⁄ Instantaneous heater didn’t work ⁄ Flow limiter in handshower isn’t re-
moved
⁄ Remove flow limiter
⁄ Shower filter seal dirty ⁄ Clean filter seal between shower and
hose
⁄ check valve hasn't moved back ⁄ Exchange check valves

04
SW 30 mm
(20 Nm)
SW 8 mm
SW 8 mm
(13 Nm)
1.
1.
2.
2.
10 mm
16549187
1
2
3
4
Montage

05
SW 3 mm
(4 Nm)
3.
2.
Armaturenfett
Grease
䀵滑油
1. 16 x 2
1.
1.
2.
2.
SW 3 mm
1.
2.
Silicone
5 6
7 8
910
Montage