Hans Grohe Pharo DP Lift 2 M 20 User manual

1
Installation Instruction
DP Lift 2 M 20
26 87x xx1
Corner tting set
26 21x 000

2
Contents
Contents
Packing List 3
Wall / Corner Installation Dimensions Diagram 4
Panel Dimensions 5
Fittings / Technical Data 6
Fitting Items / Water Connections Overview Wall Installation 7
Wall Installation 8
Fitting Items / Water Connections Overview Corner Installation 10
Corner Installation 11
Thermostat Setting / Savety Function 14
Trouble Shooting 15
Spare Parts 16
Cleaning Instruction 18
Warranty 19
Addresses 20

3
a
b
c
df
e
g
h
i
k
l
m
o
p
q
n
Tools
free from acetic acid
Fitting items Corner Installation Set
iCover
k2 Angle bracket
l4 Head screws Ø 4,5 x 60 mm with plugs
m4 Washer A 5,3 x 15
n Socket head cap screw M 8 x 18, washer A 8,4
o2 Socket head cap screws M 6 x 16, nut M 6
p 2 Washer A 6,4
q 2 EJOT screws KA 50 x 12
Fitting items Panel
aHandshower
bIsiflex B shower hose 140 cm
c1 Angle bracket
d2 Hexagon head cap screws Ø 6 x 50 mm with
plugs SX 8
e2 Washer A 6,3 x 18
f1 Set screw M 8 x 80 with 2 nuts M 8 and plug
SX 10
gOverhead shower
h2 Water connection elbows ½" with filter and non
return valve
Packing List

4
Wall installation dimensions diagram
Wall / Corner Installation Dimensions Diagram
Corner installation dimensions diagram
Before drilling the lower hole
pay attention if hot and/or cold
water supply pipes cross this
area.
Water connections (DN15, ½“) can be installed on the right or
left wall alternatively.
KW = cold water
WW = hot water
½" connection
½" connection
Shower tray floor Shower tray floor
Check for required minimum height of 87" from shower tray floor
before starting installation

5
Panel Dimensions
The panel is movable 8" downward. The stated dimensions refer to the
highest position of the panel.

6
Technical Data
Minimum flow pressure 29 psi
Operating pressure max. 147 psi*
Recommended operating pressure 29.4-73.5 psi
Test pressure 235.2 psi
Hot water temperature max. 158 °F
Safety stop 100 °F
Flow capacity at 44 psi
Hand shower (1) 1,9 gpm
Body showers, 6 jets (2) 3,9 gpm
Overhead shower 2,8 gpm
Overhead shower + body showers (3) 5,5 gpm
Hand + body showers 5,0 gpm
Fittings / Technical Data
Overhead shower
Shower hose
Thermostat grip
Bodyshower
Shut-off/selection valve
Aluminium profile
Tray
Handshower
Flow heater:
Applicable for flow heaters at min. 24 kW and 29 psi
flow pressure before the Shower panel. Only one con-
sumer possible, not two simultaneously.
Pressure differences:
The pressures of the cold and hot water connections must
be balanced.
Maintenance
The non return valves must be checked regularly accord-
ing with national or regional regulations (at least once a
year!).
From • the function is guaranteed.
* Check applicable codes
The flow rates are limited to 2.5 gpm. These
are the maximum flow rates permitted by the

7
Fitting Items / Water Connections Overview Wall Installation
Seal all drill holes with silicone free from acetic acid (not in scope of delivery)
Fitting items / water connections wall installation
Before drilling the bottom holes pay attention if hot and/or cold
water supply pipes cross this area. In this case, only drill on the
side without any supply pipes.
Dimensions
The installation dimensions stated in this installation instructions are ideal
for people of approximately 70" in body height. The dimensions can be
altered if required. In this case you will have to attend to the minimum height
of 87" from shower tray floor, and alter all the required measurements
as necessary.
If the height of water connection are outside of the illustrated range, the
drill measures have been adjusted accordingly.
(attention for minimum room height of 87 from tub-floor)
Flush through the supply pipes.
SW10 mm
SW13 mm
Ø10 mm
Ø8 mm

8
SW
24 mm
1 2
1.
2.
1.
2.
Wall Installation

9
3 4
SW 13 mm
SW
2 mm
Wall Installation
Adjustment Thermostatic mixer please see page 14

10
2x 2x
2x
1x
Fitting Items / Water Connections Overview Corner Installation
Seal all drill holes with silicone free from acetic acid (not in scope of delivery)
Fitting items / water connections corner installation
Before drilling the bottom holes pay attention if hot and/or cold
water supply pipes cross this area. In this case, only drill on the
side without any supply pipes.
Dimensions
The installation dimensions stated in this installation instructions are ideal
for people of approximately 70" in body height. The dimensions can be
altered if required. In this case you will have to attend to the minimum height
of 87" from shower tray floor, and alter all the required measurements
as necessary.
If the height of water connection are outside of the illustrated range, the
drill measures have been adjusted accordingly.
(attention for minimum room height of 87 from tub-floor)
Flush through the supply pipes.
SW
5 mm
Ø6 mm
SW10 mm
Ø6 mm
SW
6 mm