HARDWARE RESOURCES PPO2-5 User manual

STEP 1 - Measure and mark for installation
NOTE: Illustrations for measurement only. Installation of brackets and mounts will begin in Step 2
Bottom measurements Cabinet Rail Bracket Measurements
15”
A
B
15”
A
B
15”
3-29/32”
4-21/32”
3-29/32”
Front Center Rail
D
Shelf
Rear Mounting Holes
D
A
B
C
Bottom Mounting Holes
1-3/4”
1-3/4”
Bottom
of front
center rail
11/16”
1-5/16”
D
1-3/4”
2”
1-5/16” 11/16”
D
1-3/4”
2”
15/32”
Measure and mark center line of cabinet bottom. Mark center of cabinet rail for screw placement.
Rear Bracket Measurements
Front Center Rail
D
Shelf
Rear Mounting Holes
D
A
B
C
Bottom Mounting Holes
1-3/4”1-3/4”
Bottom
of front
center rail
11/16”
1-5/16”
D
1-3/4”
2”
1-5/16” 11/16”
D
1-3/4”
2”
15/32”
(Face Frame) Measure the reveal behind the center rail (D) and add to the measurements shown.
(Frameless) Measure and mark from center line as shown.
IMPORTANT:
Before you begin, make sure you familiarize yourself with all the
parts and fully read the instructions.
CUSTOMER SERVICE:
Toll-free customer help line available weekdays between
7:00am and 6:00pm CST at 800-463-0660.
TOOLS NECESSARY:
Screw gun, Phillips screwdriver, tape measure and square.
NOTE: If screw gun has a clutch, set to lowest setting so as not to
over tighten and/or strip screws.
PARTS IDENTIFICATION:
A Mounting Base 1 pcs
B Pantry Pullout Unit 1 pcs
C #10 x 1-1/2” Pan Head Phillips Wood Screw 4 pcs
D5/16-18 x 1.25 Pan Head Phillips Machine Screw 4 pcs
E #18 x 5/16 Metal Washer 4 pcs
F Almond Snap-in Cover 2 pcs
G #8 x 5/8 Pan Head Phillips Wood Screw 8 pcs
H #8 x 5/8 Flat Head Phillips Wood Screw 4 pcs
Pantry Pullout
Installation Instructions
for the PPO2 Series
C
A
E
F
H
B
D
D
G
E
Front Center Rail
D
Shelf
Rear Mounting Holes
D
A
B
C
Bottom Mounting Holes
1-3/4”1-3/4”
Bottom
of front
center rail
11/16”
1-5/16”
D
1-3/4”
2”
1-5/16” 11/16”
D
1-3/4”
2”
15/32”
(Inside cabinet view)
(Face Frame)
Part # A B
PPO2-5 1-1/4” 5/8”
PPO2-8 2” 1”
PPO2-11 4-5/16” 2-3/16”
PPO2-14 6-5/16” 3-5/32”
PPO2-5PPO2-8 • PPO2-11 • PPO2-14

STEP 4 - Install Pantry Unit
(NOTE: The adjustment screws may need to be loosed rst).
Install Pantry Pullout Unit by lining up the guide block on the bottom
of the unit with the slot in the top of the Mounting Base and slide top
U-bracket up until the drawer slide member aligns with the top mounting
bracket. Slowly push pantry unit into the cabinet until fully seated. Align
screw locations and secure rmly with four (4) – 5/16-18 x 1” Pan Head
Phillips Machine Screws as shown. Install two almond snap-in covers over
both rear screws.
E
D
D
E
Guide Block
STEP 2 - Install Mounting Base STEP 3 - Install Top Mounting Bracket
C
H
Adjustment
screws
G
Place Mounting Base in cabinet and align with marks from Step 1. Pull back
the top of the unit until the rear two holes are accessible and then securely
fasten with two (2) -- #10 x 1-1/2”Pan Head Phillips Wood Screws provided.
Pull top of unit out until the front screw holes are accessible and install with
remaining #10 x 1-1/2”Pan Head Phillips Wood Screws provided.
Separate top mounting bracket slide cabinet member as shown and align front and rear brackets with installation marks and
attach with three (3) -- #8 x 5/8 Pan Head Phillips Wood Screws in the front and with four (4) -- #8 x 5/8 Pan Head Phillips Wood
Screws in the rear as shown.
STEP 5 - Adjustments STEP 6 - Door Mounting and Adjustments
Make sure the U-bracket is
square to the pantry unit and
hand tighten the adjustment
screws. Cycle the Pantry
Pullout making sure of smooth
slide operation. Slide should
have sucient up and down
clearance for proper travel.
Make adjustments to the
adjustment screws as necessary.
Adjustment
screws
Installation
screws
Tilt adjustment (up to + 1/4”) Left/right adjustment (+/- 2-1/2”)
Up/down adjustment (+/- 1/4”)
Door panel
Door rail
Tilt adjustment
(+/- 1/8”)
Up/down adjustment
(+/- 1/4”)
Left/right adjustment
(+/- 2-1/2”)
H
Attach the door panel and adjust as shown. (NOTE: four (4) -- #8 x 5/8 Flat Head Phillips Wood Screws are provided, but
determine door panel rail thickness before using.)
PPO209/15 v.1