Harken 64.2ST E Manual

64.2ST E/HY
Electric/Hydraulic Two-Speed Self-Tailing Winch
■Required Tools
Screwdriver
Plastic Head Hammer or Mallet
Small Knife
Brush
Rags
Solvent
Oil
Grease
■Parts List
008 Pawl
038 Pawl spring
1738 Spring
5544 Spacer
5547 Gear Shaft
5548 Gear Shaft
5575 Pawl Gear
5576 Pawl Gear
5834 Bushing
6009 Screw
6150 Base Ring
6310 Screw
6337 Stainless Steel Ball
6391 Screw
6432 Screw
6480 Washer
6481 Washer
6483 Seal
6664 Screw
6666 Screw
26029 Plastic Washer
26044 Bushing
26045 Spacer
26048 Split Washer
26648 Handle Socket
27588 Thrust Bearing
27668 Stripper Arm Support
27879 Thrust Washer
28089 Ratchet Gear
28655 Washer
28656 Bushing
28657 Washer
29926 Plastic Bushing
30128 Bushing
31159 Ratchet Gear
31161 Ratchet Gear
31182 Pawl Gear
31246 Bushing
31767 Spindle
32254 Bushing
32541 Top Cap
32653 Plastic Washer
37848 Spring Support
37849 Cover
37851 Upper Jaw ST
37853 Stripper Arm
38650 Center Stem
38655 Red Line Ring
44726 Logo Support
726073 Bearing
737769 Bearing
737891 Bearing
739711 Chrome Drum
736489 Disconnet Rod Assy
742345 Bearing
937852 Lower Jaw ST
938160 Mounting Plate
938642 Base
938644 Aluminum Drum
■Suggested Service Kits
BK4512 10 008 Pawls
10 038 Springs
BK4513 100 ml Grease
When ordering parts, please include a “B”
before each number (i.e. B008).
Winch Parts
Installation
Service

1Remove Disconnect Rot and Handle Socket
Loosen disconnect rod using flethead screw driver as shown
below
Remove Disconnect Rod and handle cocket.
Disassemble Winch Before Installation
2Remove Stripper Arm and name Ring
Loosen the three (3) allen screws
Remove stripper arm
Remove Name Ring and black cover ring.
3Remove Drum Assembly
Loosen the four (4) allen screws inside the stripper arm support
Remove stripper arm support
Carefully lift off drum assembly, main bearings may remain inside
drum due to oil and grease
4Remove Housing
Loosen the six (6) allen screws holding the housing to the
alluminium base
Lift off housing.
5Remove Mounting Plate from Motor/Gearbox Ass’y
Loosen the four (4) allen screws
Lift off mounting plate:
6Drive Position
Place winch base on mounting plate, making sure fastener holes re
corresponding
Mark drive position.

Sheet entry angle
must be at least 8°.
Mount the Winch
7Determine Winch Location
Make sure there is clearance for Motor and Reduction Gearbox.
Drill an 127 mm hole through the deck.
8Position Drive Gear/Secure Mounting Base
Make sure Mounting Base sits flat on deck.
Position so Drive Gear aligns to sheet load (see Step 13)
Mark the six (6) mounting holes, drill deck.
Use bedding compound/sealant to prevent leakage.
Secure Mounting Base using five (5) 8 mm (B56) or 10 mm (B64
and up) countersunk screws.
9 Attach Motor/Gearbox Assembly to Mounting Base
Have another person below deck to position gearbox underneath winch.
12 IMPORTANT - Test Winch Operation
After winch is assembled, test operation in manual mode only,
before sailing. Important - use a lock-in winch handle.
Using a locking winch handle, check winch operation.
Disconnect rod must disconnect gearbox when lock-in
winch handle is inserted in Handle Socket.
11 Assemble Winch
Use steps 1 - 9 in reverse order to assemble winch.
10 Attach Winch
Tighten the six (6) bolts securing Winch to Mounting Base.
Use blue Loctite®on threads.
Use brush to lightly lubricate gear with grease
Position drive gear
where sheet enters
winch drum.
■Minimum/Maximum Line Diameter
Harken winches feature spring-loaded self-tailing jaws
which adjust automatically to the following line sizes:
Minimum
5
/
16
" (8 mm)
Maximum
1
/
2
" (12 mm)
■Positioning Stripper Arm
Loosen top Screw.
Remove Handle Socket.
Lift Stripper Arm and position as desired.
■Opening Winch
Remove top Screw.
Lift off Drum and Stripper Arm.
■Servicing Winch
Remove Pawls and Springs - service as below.
Remove Bearing, Gear Shaft and Gears.
Clean all parts except 37383 and 38598 with rag and solvent.
Important: Use freshwater only on parts 37383 and 38598
Use brush to lubricate all moving parts lightly with grease.
Replace Pawls and Springs and lubricate lightly with oil.
Assemble and close winch.
■Servicing Pawls
Catch Spring with knife and hold against Pawl.
Lift out Pawl. Clean and check for wear.
Place “straight leg” of Pawl Spring against Pawl.
Hold Spring closed and slip Pawl into Pawl Socket.
Lubricate Pawls using oil.
Service winch before the sailing season begins and once during
Clean all parts, except 37383
and 38598, with solvent.
Correct Incorrect
If ratchet gear is mounted
backwards, winch will slip.
Use a brush to spread a light,
even coat of grease.
Use knife to free captive Pawl
Spring. Insert Pawl Spring with straight leg
against Pawl. Use oil for lubrication.
Servicing Winch
Servicing Pawls
Pawl
Socket
13
127 mm

Wiring
1251 E. Wisconsin Ave., Pewaukee, WI 53072 USA • Tel: [phone] • Fax: [phone] • Web: www.harken.com • Email: [email protected]
Via della Cerca, 12/14, 22070 Lurago Marinone (CO) Italy • Tel: [phone] • Fax: [phone] • Web: www.harken.it • Email: [email protected]
Fasten electric control box containing solenoids to bulkhead or wall.
Install remote circuit breaker between power supply and electric
control box.
Locate pushbuttons in a convenient spot for easy winch operation.
Pushbutton wire size is #14.
Refer to wiring diagram for wire size and connection information.
Schematics Piping
control box
■Parts List
Pos. Q.ty Code Description
1 1 738157 Painted gear box and flange Assy
1 38157 Flange for worm reduction box VF63
1 35705 Cap for Gear Box Reduction
1 35695
Gear Box Redustion VF 63_P 90 B14 (G.R. 1/24)
6 6245 Screw M8x30 UNI5931
4 6277 Heli-coil M10x10
6 6487 Washer D.8 ISO 7089
2 1 833036 Painted Motor 12V 1000W
1 33036 Elettric Motor CFR 1000W 12V
4 32947 Screw stud M8
4 6487 Washer D.8 ISO 7089
4 6029 Nut M8 UNI5588
2 1 833037 Painted Motor 24V 1000W
1 33037 Elettric Motor CFR 1000W 24V
4 32947 Screw stud M8
4 6487 Washer D.8 ISO 7089
4 6029 Nut M8 UNI5588
3 1 6519 Ring
4 1 36479 Ring
5 1 35694 Albero per riduttore bonf. VF63
6 1 32954 Coupler
7 1 33043 Washer
8 1 6353 Screw M8x16 UNI6109
9 1 6178 Spring pin 6x36 DIN 1481
10 1 32649 Spring
11 2 6281 Key 8x7x35
■Parts List
Pos. Q.ty Code Description
1 1 29505 Spacer
2 1 38149 Hydraulic motor support
3 1 30849 Hydraulic motor "OMR100
151-0722 alb.scan. 1"
4 1 6519 Ring
5 1 33045 Ring carrier
6 1 36475 Toothed coupling
7 1 32649 Spring
8 1 32936 Washer
9 2 6215 Washer D.13 UNI1751
10 2 6671 Screw M12x35 UNI5931
11 1 6353 Screw M8x16 UNI6109
12 1 32648 Connecting coupling
13 1 6660 Spring pin 6x36 DIN 1481
14 4 6277 Heli-coil M10x10
WIRE SIZE CHART
(distance in meters from battery to winch and back battery)
34,6 6,1 7,6 9,1 12,2 15,2
Amps Section mm 2
5* 0,8 1 2 3 3 5 5
30 5 8 13 13 19 19 32
40 8 13 13 19 19 32 32
50 13 13 19 19 32 32 40
60 13 19 19 32 32 40 50
70 13 19 32 32 40 50 62
80 13 19 32 32 40 50 81
90 19 32 32 40 50 62 81
100 19 32 32 40 50 62 81
120 19 32 40 50 62 81 103
140 32 32 50 62 62 103 103
* Push buttons require 2 mm2 cable
4494/10-04