Harvia Digital KIP User manual

This guide should be used in conjunction with the manufacturer’s heater manual found inside the heater box.
Please be sure you and your electrician review both before installation.
Digital KIP Heater
Installation & Owner’s Guide

Read this entire manual through to the end before proceeding with the installation.
KIPW HEATER INSTALLATION MANUAL |PAGE 2
HEATER INSTRUCTIONS
Your Almost Heaven Sauna is paired with a genuine Finnish heater manufactured by Harvia Oy, the world leader in sauna heaters.
Refer to this guide for installation and operation instructions. Please note, a licensed electrician should perform all electrical
work, and Almost Heaven Saunas sta is available to assist with any questions you or your electrician may have. Please call us at
888-355-3050 for technical assistance.
PERFORMANCE EXPECTATION
Based on its cubic footage, your sauna kit has been paired with an appropriately sized heater to achieve optimal sauna
temperatures. Properly installed, you should expect your KIP heater to consistently heat your sauna to at least 170 F at
approximately head height when sitting on the bench. This temperature should be achieved in 45-60 minutes, although this
timeframe can be longer depending on the ambient temperature outdoors.
Please note, saunas at elevations greater than 5,000’above sea level may not perform as eciently as they would at sea level.
If you are above this threshold and are not achieving the aforementioned expectations, please contact Almost Heaven Saunas
technical support.
HEATER WARRANTY
Your Harvia heater comes with a 1 year warranty on the heating elements, and a 5 year warranty on the other components.
Information for your electrician:
4.5kW and 6.0kW KIP Heaters
 • 30-ampdoublepolebreaker
 • 240volts
 • 1Phase
 • 10/2wire.Ifthedistanceisgreaterthan90feetfromthepowersource,werecommendusingan8/2wireto  
accommodate for voltage drop.
 • DonotuseGFCIwiththisheater
 • Usecopperwirewith90Cinsulation
8.0kW KIP Heaters
 • 40-ampdoublepolebreaker
 • 240volts
 • 1Phase
 • 8/2wire
 • DonotuseGFCIwiththisheater
 • Usecopperwirewith90Cinsulation

KIPW HEATER INSTALLATION MANUAL |PAGE 3
Note: It is possible you will receive two temperature sensors - one in the heater box and one in the Xenio control box. They are the same
sensor - set one aside as a spare for possible later use.
The KIP heater is a wall mounted unit. Position the heater in the designated heater location in your sauna according to the
instructions below.
Removethehardwarebagfromthebaggiewiththesafetyplacards(2),selectingthetwolongerlagscrews(1.5”).Youwillsecure
theseintothesaunawallsothat¼”ofthescrewprotrudesfromthewall
a. For barrel saunas,the11/2”lagscrewsshouldbemountedapproximately20”othelowestpointofthebarrelandspaced15
1/4”apartandcenteredabovetheventholes.Note:TheheaterwillconcealaportionoftheLEDlight.Thisisnormal.
b. For indoor saunas,thescrewsshouldbemounted20”otheoor,andspaced151/4”apartapproximatelycenteredabovethe
ventholes(ifpresent).Itisnethattheheateriscoveringtheholesasventilationstilloccurs.
20”
15 ¼ ”
20”
15 ¼ ”
Touchpad
Temperature sensor
PowerUnit

KIPW HEATER INSTALLATION MANUAL |PAGE 4
Hangtheheateronthemountingscrewstoensureitislevelandthatitsbasesits5-7”otheoorofthesauna.
If these criteria are met, make a mark on the wall of the sauna directly behind one of the rubber gaskets on the lower back of the
heater; this will be where the power enters the sauna. Take the heater o the wall and remove the rubber gasket, exposing the
cutout. It does not matter which gasket is removed.
NOTE: While this location is the most common, the power can enter the sauna at any location. It is not recommended you use the pre-
drilled vent holes as an entrance for the conduit.
Removethetwoscrewsholdingthestoneguardinplace.Prytheguardbackandliftuptoremoveit.Cliptheziptieholdingthe
heating elements in place being sure the tie doesn’t fall into the heater.
Flip the heater on its back and remove the bottom cover so your electrician can gain access to the terminal block.

KIPW HEATER INSTALLATION MANUAL |PAGE 5
POSITIONING THE HEATER COMPONENTS
Indoor Saunas
For indoor sauna applications, mount the power unit on or near the sauna. It can be mounted on the exterior of the sauna, or on
anadjacentwall.Themainpowerforyourheaterwillconnecthererst,andthenrelayontoyourheater.Next,considerwhere
you’d like to mount your touchpad. You can mount the touchpad wherever it’s most convenient for you. We do not recommend
mounting the touchpad in the sauna itself.
Outdoor Saunas
Neitherofthesecomponentsarewaterproof,soproperprecautionsshouldbetakenforoutdoorsaunaapplications.Please
consider the following:
Power Unit
• Thepowerunitshouldbemountedinadrylocation.Ifitcannotbemountedinadry
location, then it should be mounted in a ventilated weatherproof enclosure.
• Pleasenotethatthetemperaturesensorthatcomeswiththesaunakithasa15’reach-the
sensor is mounted in the sauna and connects to the power unit. If the sauna is located
greater than this distance away from where the power unit is installed, then the power
unit should be mounted nearer to the sauna in a weatherproof enclosure with proper
ventilation. The image on the right is an example of an enclosure. Alternatively, you can
purchase a longer temperature sensor wire directly from Almost Heaven Saunas.
Touchpad
• Thetouchpadshouldbemountedindoorsinadryarea.
• Thetouchpadconnectstothepowerunitwiththeprovided20’datacable.Ifyouneedalongerdatacableforyour
application, you may purchase one directly from Almost Heaven Saunas.

KIPW HEATER INSTALLATION MANUAL |PAGE 6
CONNECTING YOUR HEATER TO POWER
Pleasenote,thepowerunitprovided(CX170-U1-15)withyoursaunaisratedforsingle-groupconnection.Theinstructionsbelow
are for single group connections only.
Incoming Power
First, you will need to bring power to your power unit. Remove the power unit’s cover and pry
out the appropriate knockouts that will allow the wiring to enter and exit the unit.
Connectthepowercordtotheappropriateterminals,withthetwohotlinesconnecting
totheleft-mostL1andL2terminals,andthegroundconnectingtothegroundterminal.A
neutral line is not needed - this is only required if a light or ventilation fan is connected to the
powerunit,anapplicationthatisnotavailableintheU.S.market.
Outgoing Power
Next,you’llwanttorelaypowertotheheateritself.
First,connectthegroundatthepowerunittothegroundterminalattheheater.Next,
connectoutgoingL1toT1attheheater,andoutgoingL2toT3attheheater.Next,complete
thehigh-limitsafety-circuitbyconnectingA1atthepowerunittoT2attheheater,andA2
atthepowerunitunittoT4attheheater.Youmayusestrandsof12gawireforthehigh-limit
safety circuit connections.
***NOTE: If your heater arrived with copper jumpers pre-installed in the heater’s terminal block,
please remove and discard these. These are not needed.
Temperature Sensor
The temperature sensor mounts in your sauna and provides feedback to the power unit
regardingthetemperatureinyoursauna.Weadvisemountingthissensorapproximately14”tothesideoftheheater,and
approximately14”belowthehighestpointofthe
sauna.Usetheprovidedhardwaretomountthesensor.

KIPW HEATER INSTALLATION MANUAL |PAGE 7
Next,feedthesensorwireoutofyoursaunainordertoconnecttothepowerunit.
Secure the wiring to the circuit board mini-terminal. Starting on the outside and moving in, the wires should connect in the
following order: blue - white - red - yellow.
Touchpad
The touchpad should be mounted indoors in a dry location, preferably in your
home.Onceyou’vedeterminedthislocation,useaatheadscrewdrivertogently
pry the screen of the touchpad from the mounting bracket. Feed the data cable
through the hole in the mounting bracket, and mount the bracket to the location
you selected. Push the data cable connector into the port on the back of the screen
and snap the screen back into the bracket.
Next,connecttheothercabletotheportclosesttothepowerunit’smini-terminal
block that is connected to the temperature sensor. Replace the power unit’s cover
and turn the power switch to the on position.
PLACING THE STONES
Rinse your sauna stones to prepare them for placement. Beginning between the back wall and back heating element, place the
smaller stones in between and around the three heating elements being sure that the heating elements stay in their original
vertical position and do not touch each other. The stones should touch the elements, but not bend them. Reserve the
larger stones for placement on top of the heating elements, covering them completely. Replace the stone guard you removed at
the beginning of the heater installation.
Note:Packingstonesintootightlywillrestrictairowandaecttheeciencyofyourheater.Looselypositionthestonesaround
and above the heating elements. It is common to have 5-10 stones left over.
Temperature Sensor
Touchpad data cable

KIPW Heater Installation & Owner’s Manual
almostheaven.com
OPERATING YOUR HEATER
Note:Yourtouchpad’sdefaultsettingsarecompatiblewithyourheater.Nochanges
are necessary.
Immediate Start
Turn your breaker on. If everything is connected correctly, the buttons at the bottom of the
screen should illuminate. The bottom left button is the main power unit - press it, and you
shouldhearaloud“clunk”fromthepowerunit,whichisthecontactorsengaging.Ifyoudo
nothing, it will begin heating immediately; the display will show the current temperature in the
sauna, as well as the time remaining on the heat cycle.
Delayed Start
Turnthepowerbuttononthetouchpad.Press“menu”untiltheclockiconisashing.Adjustthe
preset time by pressing + or - until you get to the desired preset time. You are able to preset your
heaterin10minuteincrementsforupto12hours.Thetimeremainingbeforeyourheaterbegins
heating should appear below the brackets at the top of the touchpad.
Setting the Temperature
The temperature displayed on the screen is the temperature inside the sauna where the temperature sensor is mounted. To set
yourdesiredsaunatemperature,pressthepowerbuttononthetouchpad.Press“menu”untilthethermometericonashes.
Adjust the temperature with the + or - until your desired temperature is displayed. The sauna will heat to and hover around this
temperature.
GENERAL OPERATION INFORMATION
• YourDigitalKIPheaterisULcertied.Becauseofthis,itisrequiredtoshutoafteronehourofuse.Ifyouwishtocontinue
your sauna session, you will have to restart the heater if the heating period times out.
• Ifyourheaterisn’theating,turnoyourbreakerandtrypressingtheresetbuttonundertheheaterasthehigh-limitsafety
circuit may have been tripped. If this continues to happen, your sensor may be too high or too close to the heater.
• Thisisatraditionalsaunaheaterwithsaunastones.Assuch,youmaypourwaterontothestonesaccordingtoyour
humidity level preference. Please note, however, it often only takes a ladle-full to achieve the desired eect.
If there is an error code displayed on the touchpad, please refer to the error code list found in the manufacturer’s manual
12-2022