Harvia sentiontec Concept R mini Series User manual
EN
Version 11/17 Ident. no. CP-RM-MA
INSTRUCTIONS FOR INSTALLATION AND USE
English
Sauna heater
Concept R mini
CP-RM-35 / 1-030-892: Concept R mini 3.5 kW
CP-RM-45 / 1-030-962: Concept R mini 4.5 kW
CP-RM-60 / 1-030-984: Concept R mini 6.0 kW
CP-RM-75 / 1-038-852: Concept R mini 7.5 kW
Table of Contents
1. About this instruction manual 4
2. Important information for your safety 5
2.1. Intended use 5
2.2. Safety information for the installer 6
2.3. Safety information for the user 7
3. Product description 9
3.1. Scope of delivery 9
3.2. Accessories 9
3.3. Product functions 9
4. Installation and connection 10
4.1. Installation location and sensor position 10
4.2. Safety distances 11
4.3. Installation on the cabin wall 12
4.4. Installation with foot (optional) 14
4.5. Connection diagram for 400 V 3N~ 16
4.6. Connection diagram for 230 V 3~ 16
4.7. Connection diagram for 230 V 1N~ 17
4.8. Wiring diagrams 18
4.9. Electrical connection 19
5. Commissioning 20
5.1. Filling the stone container 20
21
EN
6. Operation 22
6.1. Operating the sauna heater 22
6.2. Infusion 22
7. Maintenance 23
23
7.2. Cleaning the sauna heater 23
7.3. Changing the sauna stones 23
8. Disposal 24
9. Problem-solving by the installer 25
10. Dimensions 26
11. Technical data 27
Instructions for installation and use p. 4/28
1. About this instruction manual
Carefully read these instructions for installation and use, and keep them near
the sauna. This ensures that you can refer to information about your safety and
the operation at any time.
Symbols used for warning notices
an activity indicates that this activity poses a risk. Always observe the warning
notices. This prevents damage to property and injuries, which in the worst case
may be fatal.
The warning notices contain keywords, which have the following meanings:
DANGER!
Serious or fatal injury will occur if this warning notice is not observed.
WARNING!
Serious or fatal injury can occur if this warning notice is not observed.
CAUTION!
Minor injuries can occur if this warning notice is not observed.
ATTENTION!
This keyword is a warning that damage to property can occur.
Other symbols
This symbol indicates tips and useful information.
Do not cover Read the operating instructions
These installation and operating instructions can also be found in the
downloads section of our website: www.sentiotec.com/downloads.
EN
Instructions for installation and use p. 5/28
2. Important information for your safety
The Concept R mini sauna heater has been produced in accordance
with the applicable safety rules and regulations. However, hazards
may occur during use. Therefore adhere to the following safety in-
2.1. Intended use
The Concept R mini sauna heater is intended solely for heating
sauna cabins, in conjunction with a sauna control unit which does
not include a remote start function.
The Concept R mini sauna heater can also be used with a sauna
control unit with a remote start function, but only in conjunction with
the optional safety shutdown feature.
The Concept R mini sauna heater can also be used in public saunas,
but only in conjunction with the optional safety shutdown feature.
use can result in damage to the product, severe injuries or death.
Instructions for installation and use p. 6/28
2.2. Safety information for the installer
Installing and connecting the sauna heater may only be performed
when the power supply is disconnected.
A fully disconnecting all-pole isolating device compliant with
Always use silicone cables that are heat-resistant up to 150 °C
to connect the sauna heater.
Only install one sauna heater in the cabin. The Concept R mini
sauna heater must not be used together with other sauna heaters
in a sauna cabin.
The roof and walls of the sauna cabin must be manufactured
from low-resin, untreated or thermally treated wood, e.g. Nordic
-
als. If laminated wooden materials are used, make sure that the
adhesive used in them does not give off formaldehyde. If other
materials than wood are used in the sauna cabin, these materi-
als must be heat-resistant and corrosion-resistant and must not
cause any negative effects on the health of the sauna users.
The height of the sauna cabin must be at least 1.9 m.
sauna cabin in chapter 11. Technical data.
When positioning the sauna heater, observe the minimum safety
distances (see chapter 4.2. Safety distances).
Also comply with the regulations applicable at the installation
location.
For your own safety, consult your supplier in the event of prob-
instructions.
EN
Instructions for installation and use p. 7/28
2.3. Safety information for the user
The device must not be used by children under 8 years of age.
The device may only be used by children over 8 years of age,
by persons with limited psychological, sensory or mental capa-
the following conditions:
– They are supervised.
– They have been shown how to use the device safely and
are aware of the hazards that could occur.
Children must not play with the device.
Children under 14 years of age may only clean the device if they
are supervised.
-
ence of alcohol, medication or drugs.
Never operate the sauna heater without sauna stones, as this
Instructions for installation and use p. 8/28
-
na heater before the sauna control unit is switched on.
Heat up the sauna heater for half an hour BEFORE using the
this period. Then ventilate the sauna cabin well (see 5.2. Heating
on page 21).
Never touch the sauna heater while it is operating. The surfaces
For your own safety, consult your supplier in the event of problems
EN
Instructions for installation and use p. 9/28
3. Product description
3.1. Scope of delivery
Sauna heater
Instructions for installation and use
3.2. Accessories
Accessories Item number
Set of brackets for the Concept R mini
heater railing
CP-RM-HSR / 1-027-993
Wood railing for Concept R mini, lime wood CP-RM-L / 1-034-213
Wood railing for Concept R mini, walnut CP-RM-N / 1-034-211
Foot for Concept R mini heater CP-RM-SF / 1-043-964
Foot cover for Concept R mini, lime wood CP-RM-CSF-L / 1-041-482
Foot cover for Concept R mini, walnut CP-RM-CSF-N / 1-041-483
3.3. Product functions
The Concept R mini sauna heater is a Finnish sauna heater and makes it possible
to produce a typical Finnish sauna climate of 80 to 100 °C with an air humidity
4. Installation and connection
Take the following points into account when positioning and connecting the
sauna heater:
A fully disconnecting all-pole isolating device compliant with overvoltage
The Concept R mini sauna heater is a wall-mounted heater. Before starting
4.1. Installation location and sensor position
Position the heater centrally in front of the air intake opening on the cabin wall.
Fig. 1.
above the centre of the sauna heater. Maintain a distance of 15 cm to the sauna
cabin roof.
WARNING!
Danger of electric shock
The sauna heater may only be installed and connected when the
power supply is disconnected.
min. 900
min. 50
450
692
220
min. 50 ~
~
EN
Fig. 1 Safety distances for the
Concept R combi 3.5 kW, 4.5 kW, 6.0 kW and 7.5 kW
(CP-RM-35 / CP-RM-45 / CR-RM-60 / CP-RM-75)
Dimensions in mm
4.2. Safety distances
Fig. 1.
4.3. Installation on the cabin wall
Observe Fig. 1, Fig. 2, Fig. 3 and Fig. 4 (page 11, 12, 13).
1. Attach the mounting rail 1 to the wall horizontally using the wood screws
supplied 2. Observe the minimum distances for the heater shown in Fig. 4.
2. Suspend the heater 3 from the mounting rail from above, moving it down-
3. Secure the heater 3 using the lock screws supplied 4 on the mounting rail 1.
Fig. 2 Position of the mounting rail for Concept R mini
Dimensions in mm
2
WARNING!
supplied lock screw 4 for attachment.
1
210210
440
420
EN
63
5
5
Fig. 3 Position of the mounting rail for Concept R mini
Dimensions in mm
Fig. 4 Securing the Concept R mini (wooden railing)
1
3
4
1
63
5 5
4.4. Installation with foot (optional)
Observe Fig. 1, Fig. 5, Fig. 6 (page 11, 14, 15).
1. Attach the foot 1 using the screws enclosed 2 to the bottom of the heater.
Please note that the round recess is on the evaporator side.
2. Fig. 6). Depending
the corresponding screws. Observe the minimum distances for the heater
shown in Fig. 1.
WARNING!
on the substrate onto which the sauna cabin is built – NOT on the
Fig. 5 Installing the foot on the Concept R mini
2
1
EN
Fig. 6
Fig. 7 Installing the wooden cover for the foot (optional)
Place the two halves of the cover ring around the foot and press them together
L1 L2 N
L3 U
V
N
Wr
r
w
w
U
V
NW
W
400V 3N~
NVNU
PE
N
L2
L1
L3
4.5. Connection diagram for 400 V 3N~
Fig. 8
2
3
4
1
Connection diagram for the Concept R mini
3.5 kW, 4.5 kW, 6.0 kW and 7.5 kW
(CP-RM-35 / CP-RM-45 / CR-RM-60 / CP-RM-75)
L1 L2 N
L3 U
V
N
Wr
r
w
w
U
V
NW
W
230V 3~
NVNU
PE
L2
L1
L3
4.6. Connection diagram for 230 V 3~
Fig. 9 Connection diagram for the Concept R mini
3.5 kW, 4.5 kW and 6.0 kW
(CP-RM-35 / CP-RM-45 / CR-RM-60)
1
4
3
2
*
EN
1 Sauna control unit
2
3 Sauna heater
4 Power supply
Remove the copper bridge
*
L1 L2 N
L3 U
V
N
Wr
r
w
w
U
V
NW
W
230V 1N~
NVNU
L
PE
N
4.7. Connection diagram for 230 V 1N~
Fig. 10 Connection diagram for the Concept R mini
3.5 kW, 4.5 kW, 6.0 kW and 7.5 kW
(CP-RM-35 / CP-RM-45 / CR-RM-60 / CP-RM-75)
2
1
4
3
*
CP-RM-75
7.5 kW
CP-RM-35
3.45 kW
U V W N
1,15kW
1,15kW
1,15kW
N N
W V U
CP-RM-60
6.0 kW
4.8. Wiring diagrams
CP-RM-45
4.5 kW
U V W N
1,5kW
1,5kW
1,5kW
N N
W V U
U V W N
2,0kW
2,0kW
2,0kW
N N
W V U
to the control unitto the control unit
to the control unit
U V W N
2,5kW
2,5kW
2,5kW
N N
W V U
to the control unit
U
V
W
N
PE
EN
Connecting the Concept R 3.5 kW, 4.5 kW, 6.0 kW and 7.5 kW
(CP-RM-35 / CP-RM-45 / CR-RM-60 / CP-RM-75)
1. Guide the connection cable through the feed-
through 4.
2. Connect the connectors of the connection
cable to the U – V – W – N – PE terminals
of the sauna heater and to the applicable
sauna control unit terminals. Observe the
installation instructions for the sauna control
unit when doing so.
3. Reattach the cover panel 1 to the heater.
4.9. Electrical connection
1. Unscrew the screws 2 and 3 with a screwdriver.
2. Remove the cover plate 1.
4
2
3
1
Instructions for use for the user p. 20/28
5. Commissioning
5.1. Filling the stone container
The amount of stones suited to your heater can be found in chapter 11. Tech-
nical data (see page 27).
1. Wash the stones thoroughly using water and a brush before use. Do not
use any cleaning additives.
2.
and remove any remaining packaging.
3. Place the stones in the stone container. Stack the sauna stones loosely so
4. Make sure that the sauna stones do not protrude beyond the edge of the
stone container.
WARNING!
If the sauna heater is used without sauna stones, the cabin walls will
NEVER operate the sauna heater without the sauna stones.
This manual suits for next models
8
Table of contents
Other Harvia Heater manuals
Harvia
Harvia sentiotec Qube User manual
Harvia
Harvia PO12-U1 Owner's manual
Harvia
Harvia Digital KIP User manual
Harvia
Harvia Delta D23EE User manual
Harvia
Harvia FG Series User manual
Harvia
Harvia HL70S User manual
Harvia
Harvia K10G-U1 User manual
Harvia
Harvia KIP-30-B1 Owner's manual
Harvia
Harvia SENTIO Qube 240 Guide
Harvia
Harvia sentiotec Concept R mini combi User manual
Harvia
Harvia KUBIC COMBI User manual
Harvia
Harvia JM-20 Instructions for and use User manual
Harvia
Harvia HYB300230S Guide
Harvia
Harvia AV-4 Guide
Harvia
Harvia HCBU1712241 Owner's manual
Harvia
Harvia Delta E HDE360400 User manual
Harvia
Harvia FORTE User manual
Harvia
Harvia HPCS6U1HB User manual
Harvia
Harvia CS60 User manual
Harvia
Harvia KV-80 User manual
Popular Heater manuals by other brands
Pacific energy
Pacific energy The Mirage A Series Installation and operating instructions
Tylo
Tylo Expression manual
SKF
SKF EAZ Instructions for use
Honeywell
Honeywell HZ2200 - Mini-Tower 1500W Heater Fan owner's manual
Mesa Living
Mesa Living 804.167 instruction manual
Stelpro
Stelpro PDH’ series user guide
