Haws 1109FR Guide

01/19 Model 1109FR Page 1 of 4
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [email protected] website: www.hawsco.com
No. 0002076626 (14)
Model 1109FR
Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material
or poor workmanship for a period of one year from date of shipment. HAWS
liability under this warranty shall be discharged by furnishing without charge F.O.B.
HAWS Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided
that claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS,
Sparks, Nevada. HAWS will not be liable for any damages caused by defective
materials or poor workmanship, except for replacements, as provided above. Buyer
agrees that HAWS shall not be liable for general, special, or consequential
damages claimed to arise under the contract of sale. The drinking fountain
manufactured by HAWS is warranted to function if installation and maintenance
instructions provided are adhered to. The units also must be used for the purpose
for which they were intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

01/19 Model 1109FR Page 2 of 4
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/64“ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open
end wrench.
LOCATION OF UNIT: The Model 1109FR Drinking Fountain is a wheelchair accessible
drinking water facility. The height dimensions shown, meet current ADA requirements.
When installing this unit, local, state or federal codes should be adhered to.
If height other than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Waste outlet is 1-1/4” IPS (located on 6521FR Valve box).
MAINTENANCE: Periodically clean the strainer. Refer to 6521FR Valve Operation and
Maintenance Sheet for more information.
TROUBLESHOOTING
PROBLEM REPAIR CHECKLIST
1. Insufficient bubbler flow. 1a. Check that inlet screwdriver stop valve
is wide open. (Customer supplied).
Turn counterclockwise.
b. Verify minimum 30psi flowing supply
pressure.
c. Adjust valve to increase flow. Use
front adjust screw see 6521FR Valve
Manual.
General Notes:
Before tightening nut and ferrule assembly, push tubing into fitting until it bottoms out
to ensure correct engagement with O-Ring.
For more information about Haws products, see our website: www.hawsco.com
© Haws®Corporation – All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

1
2
3
4
5
4
2
5
1
OPTIONAL
3
PARTS BREAKDOWN
BACK PANEL
BUBBLER HEAD
PUSH BTN ASS'Y
BOTTOM PLATE
FREEZE RESISTANT VALVE
DETAIL OF ITEM 2
ROTATED 90° INTO VIEW
DETAIL A
A
6521FR
PBM1109
5881PBA
5703M
BP3
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
PAGE
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
ITEM DESCRIPTION
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
PART NO.
FV 06-08-98
14
0002076626
1109FR
1:4
11
IR 04/16/19
.
DP
3 OF 4
PARTS BREAKDOWN
5387
2019
FV
ENSURE TUBE IS DISCONNECTED FROM
"PUSH-IN" TYPE CONNECTOR ON PRESSURE
REGULATOR PRIOR TO REMOVAL. APPLY A DROP
OF LOCTITE 222MS ON NOZZLE THREADS PRIOR
TO REASSEMBLING BACK ONTO BUBBLER HEAD.
REATTACH TUBE TO "PUSH-IN" TYPE
CONNECTOR ENSURING IT IS FULLY BOTTOMED
OUT.
1
NOTE:
REMOVE INSERT
WITH
5/16 HEX SOCKET
(NOT SUPPLIED)
1

HEIGHT
HANDICAP
BOX
DEPTH
OF 102mm
4"
51mm
2"
SUPPLY
514mm
*20-1/4"
876mm
*34-1/2"
152mm
6"
WALL FACE
FLOOR LINE
WASTE
565mm
*22-1/4"
305mm
12"
457mm
18"
2-1/8"
54mm
SUPPLIED)
SUPPLY (NOT
1/2" IPS
SUPPLIED)
WASTE (NOT
1-1/4" IPS
SUPPLY
FREEZE PROTECTED
AIR LINE 76mm
3"
254mm
10"
438mm
*17-1/4"
356mm
14"
SLOTS
MOUNTING
9.5mm
3/8"
Ø
TO FLOOR
697mm
27-7/16"
3-1/4"
83mm83mm
3-1/4"
WASTE
130mm
5-1/8"
686mm
*27"
MOUNTING DETAIL
1-1/4" O.D. WASTE W/1-1/4
SLIP JOINT NUT AND WASHER
(FROM DRINKING FOUNTAIN)
1-1/4" IPS NIPPLE (NOT SUPPLIED)
1-1/4 NPT (F)
ELBOW TO TRAP
SUPPLY
9"
229mm
15"
381mm BACK PANEL OPTIONAL ON 1109FR
1/2"
12.7mm (W/OPT. BACK PANEL)
76mm
3"
3"
76mm SUPPLY
AIR LINE
(TO SPOUT OUTLET)
DIMENSIONS MARKED (*) MUST BE ADJUSTED
INSTALLATION HEIGHTS OTHER THAN SHOWN,
FEDERAL CODES SHOULD BE ADHERED TO. FOR
WHEN INSTALLING THIS UNIT LOCAL, STATE OR
HOLD ROUGH-IN DIMENSIONS ± 1/4" (6.4mm).
*
ACCORDINGLY.
3/8 OD VINYL SUPPLY TUBING (CONNECT
TO BUBBLER WITH SUPPLIED UNION, TRIM
TO FIT)
7/8 OD INSULATING TUBING (MUST
COVER ENTIRE SUPPLY TUBING, FROM
BUBBLER TO MODEL 6521FR FREEZE VALVE
ASSEMBLY,TRIM TO FIT)
6521FR FREEZE
RESISTANT VALVE
ASSEMBLY
1-1/4" O.D. X 7 1/2 LG."
WASTE ARM (SUPPLIED)
6521 VALVE ASSEMBLY
ACCESS PANEL
THIS FOUNTAIN REQUIRES THE USE OF MODEL
6521FR FREEZE RESISTANT VALVE ASSEMBLY
(SOLD SEPARATELY)
1
VALVE ASSEMBLY MUST BE INSTALLED IN A
WARM AREA. PROVISIONS SHOULD BE MADE
TO ALLOW ACCESS TO ACCESS PANEL
2
4.
3.
2
2
1
3/8 MOUNTING
HARDWARE
(BY OTHERS)
(SUPPLIED WITH
6521 FREEZE VALVE)
12.7mm
1
2"
MOUNTING PLATE
(MODEL 6700, OPTIONAL)
SEE DETAIL A
DETAIL A
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
F.V.
06-01-98
14
0002076626.D
1109FR
1:16
11
IR 04/16/19
.
DP
4 OF 4
INSTALLATION
5387
2019
FV
51mm
2"
76mm
3"
BACK VIEW
NOTES:
6521FR
VALVE
SYSTEM
AIR LINE
64mm
2-1/2"