Haws 1117LN Guide

11/17 Model 1117LN Page 1 of 4
No. 0580000675 (2)
1455 Kleppe Lane Sparks, NV 89431-6467 [phone] Fax [phone]
E-mail: [e-mail]  website: www.hawsco.com
Model 1117LN
Drinking Fountain
INSTALLATION, OPERATION
&
MAINTENANCE INSTRUCTIONS
LIMITED WARRANTY
HAWS warrants that this specific product is guaranteed against defective material or
poor workmanship for a period of one year from date of shipment. HAWS liability
under this warranty shall be discharged by furnishing without charge F.O.B. HAWS
Factory any goods, or part thereof, which shall appear to the Company upon
inspection to be of defective material or not of first class workmanship, provided that
claim is made in writing to Haws within a reasonable period after receipt of the
product. Where claims for defects are made, the defective part or parts shall be
delivered to the Company, prepaid, for inspection. HAWS will not be liable for the
cost of repairs, alterations or replacements, or for any expense connected therewith
made by the owner or his agents, except upon written authority from HAWS, Sparks,
Nevada. HAWS will not be liable for any damages caused by defective materials or
poor workmanship, except for replacements, as provided above. Buyer agrees that
HAWS shall not be liable for general, special, or consequential damages claimed to
arise under the contract of sale. The drinking fountain manufactured by HAWS is
warranted to function if installation and maintenance instructions provided are
adhered to. The units also must be used for the purpose for which they were
intended.
NO OTHER WARRANTIES EXPRESSED OR IMPLIED ARE AUTHORIZED,
PROVIDED OR GIVEN BY HAWS.
NOTE TO INSTALLER: Please leave this information with the Maintenance Department.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE INSTALLATION OF THIS
MODEL PLEASE CALL:
TECHNICAL SUPPORT: 1-800-766-5612
FOR CUSTOMER SERVICE: 1-888-640-4297

11/17 Model 1117LN Page 2 of 4
RECOMMENDED TOOLS: Hack saw, pipe joint sealant, screwdriver, level, 12" adjustable
wrench, 10" pipe wrench, 5/64“ hex key wrench, 9/16”, 1/2", 7/16” socket wrench or open end
wrench.
LOCATION OF UNIT: The Model 1117LN Drinking Fountain is a wheelchair accessible
drinking water facility. The height dimensions that are shown meet current ADA requirements.
When installing this unit, local, state or federal codes should be adhered to.
If height other than shown is required, then dimensions must be adjusted accordingly.
SUPPLY LINE: The minimum recommended line size is 1/2“IPS with 30-90 psi (2-6 ATM)
flowing pressure. Where sediment or mineral content is a problem, an inlet filter is
recommended.
PLUMBING CONNECTIONS: Inlet is 3/8“O.D. push-in type fitting. Waste outlet is female
1-1/4” IPS.
MAINTENANCE: Periodically clean the strainer. Refer to 5874 Series Valve Manual for more
information.
INSTALLATION PROCEDURE
GENERAL NOTES:
1. For all plastic push-in type fitting connections, only connect NSF-61 copper or
plastic tubing. Stainless steel or glass tubing is not recommended. The
following assembly instructions must be followed to ensure a watertight
connection:
a. Cut tubing square and clean.
b. Mark from end of tube the length of insertion (See table below).
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Tube Sizes
O.D.
Tolerance Insertion Depth
1/4”
±.005”
11/16”
3/8”
±.005”
3/4”
1/2”
±.005”
7/8”
TROUBLESHOOTING
PROBLEM
REPAIR CHECKLIST
1.
Insufficient bubbler flow.
1a.
Check that inlet screwdriver stop valve is wide
open. Turn counter-clockwise.
b.
Verify minimum 30 psi flowing supply pressure.
c.
Clean strainer. See 5874 Series Valve Manual
d.
Adjust valve to increase flow. Use front adjust
screw or see 5874 Series Valve Manual.
For more information about Haws products, see our website: www.hawsco.com
© 2017 Haws®Corporation – All Rights Reserved
HAWS® and other trademarks usedin these materials are the exclusive property of Haws Corporation.

A
PARTS BREAKDOWN
7
6
8
1
4
5
APPROVED
DRAWN
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BYECN NO.
PAGE
DATE
DATE
ECN:
REVISED PER
CHKD
Haws Corporation - All Rights Reserved
HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
WHEN ORDERING PARTS PLEASE SPECIFY MODEL NUMBER.
GC
08/23/17
2
0580000675
1117LN
1:1
11
FV 11/22/17
5221
GC
3 of 4
PARTS BREAKDOWN
5255
2017
JP
(OPTIONAL)
(OPTIONAL)
4
5
7
8
ITEM DESCRIPTION 1117LN
STRAINER, WASTE ASSY
BUBBLER HEAD ASSY, PCP 5703M
6462
TRAP 0005982900
PLATE MOUNTING 6700.4
PLATE BOTTOM PBM1107
REF
4
ROTATED 90° INTO VIEW
DETAIL A
REMOVE INSERT
WITH 5/16 HEX SOCKET
(NOT SUPPLIED)
2
1
2
3PUSH BUTTON ASSY
VALVE REPAIR KIT
BUTTON, PUSH, FLANGED, PCP W/ VALVE 5874PBF
VRK5874
PBA6
NOTES:
1 5874PBF (ITEM 2) INCLUDES VRK5874 CARTRIDGE ASSEMBLY
(ITEM 3) AND PBA6 FLANGED PUSH BUTTON (ITEM 4).
2 ENSURE TUBE IS DISCONNECTED FROM PUSH BUTTON
VALVE BODY PRIOR TO REMOVAL. APPLY ONE DROP OF
LOCTITE 222MS TO NOZZLE THREADS PRIOR TO FASTENING
BACK ONTO BUBBLER HEAD. RE-ATTACH TUBE TO VALVE.
2
3
6
1
1
1

TO FLOOR
406mm
254mm
10"
305mm
12"
(OPTIONAL, HAWS 6700.4)
MOUNTING PLATE
406mm
813mm
32"
914mm
36"
16" 16"
203mm
8"
686mm
*27"
BACK PANEL
413mm
16-1/4"
406mm
16"
203mm
8"
8"
C
1. HOLD ROUGH-IN DIMENSIONS ± 1/8" (3.2mm).
2. WHEN INSTALLING THIS UNIT, LOCAL, STATE, OR FEDERAL CODES
SHOULD BE ADHERED TO. FOR INSTALLATION HEIGHTS OTHER THAN
SHOWN, DIMENSIONS MARKED (*) MUST BE ADJUSTED ACCORDINGLY.
3 REFER TO 5874SS/VRK5874 OPERATION AND MAINTENANCE MANUAL FOR
PUSH BUTTON AND VALVE INSTALLATION/MAINTENANCE INSTRUCTONS.
NOTES:
3
L
C
L
(NOT SUPPLIED)
(NOT SUPPLIED)
2X 2-7/8"
[73mm]
12
[305mm] 12
[305mm]
3"
[76mm] 1-1/4" IPS WASTE
(NOT SUPPLIED)
SUPPLY STOP AND
3/8" OD SUPPLY
1/2" IPS SUPPLY
3"
[76mm]
27-13/16"
[706mm]
33-3/4"
[857mm]
SUPPLY
Ø7/16"
[Ø11mm]
SUPPLY
WASTE
3"
[76mm]
WASTE
2-1/2"
[64mm]
4-1/4"
[108mm] 8-1/2"
[216mm]MOUNTING DETAIL
MOUNTING
HOLES
BACK VIEW
203mm
38-3/4"
[984mm]
27"
[686mm]
23-7/8"
[606mm]
FLOOR LINE
18-1/2"
[470mm]
1/2"
[13mm]
MOUNTING PLATE
35-3/16"
[894mm]
35-1/2"
[902mm]
29-1/4"
[743mm]
29-5/16"
[751mm]
1-1/4" IPS TRAP
(SUPPLIED)
WALL FACE
1-1/4" IPS WASTE
(NOT SUPPLIED)
32-13/16"
[833mm]
32-15/16"
[837mm]
(OPTIONAL)
4-1/4"
[108mm]
3/8" O.D SUPPLY
(NOT SUPPLIED)
3/8" MOUNTING BOLTS
(NOT SUPPLIED)
APPROVED:
DRAWN:
PART NUMBER
SCALE: SHEET OF
REVISION
DRAWING TYPE: SIZE: A
BY:ECN NO.
PAGE
DATE:
DATE:
ECN:
REVISED PER
CHK'D.:
Haws Corporation - All Rights Reserved. HAWS and other trademarks used in these materials are the exclusive property of Haws Corporation.
CR
MODEL(S)
1455 KLEPPE LANE
SPARKS, NEVADA 89431
[phone] FAX [phone]
E-MAIL: [email protected]
WEBSITE: WWW.HAWSCO.COM
THIS DOCUMENT IS TRUE AND CORRECT AT TIME OF PUBLICATION. CONTINUED PRODUCT IMPROVEMENTS
MAKE SPECIFICATIONS AND MEASUREMENTS SUBJECT TO CHANGE WITHOUT NOTICE.
GC
08/23/17
2
0580000675.D
1117LN
1:14
11
FV 11/22/17
5221
GC
4 of 4
INSTALLATION
5255
2017
JP