Hay FIFTY-FIFTY WALL User manual

– INSTRUCTION MANUAL –
DESIGN BY SAM WELLER
FIFTY-FIFTY WALL

 GENERAL INFORMATION 
TECHNICAL DATA
This product is supplied with an integrated LED
light source. The expected lifespan of the LED
light source is 25,000 hours, which equates to
810 years of general use. When the light source
reaches its end of life, the whole luminaire should
be replaced.
FITTING TYPE | Integrated LED
POWER W | 7,7W
COLOUR TEMPERATURE | 3000K warm white.
ATTENTION
Ensure that the power supply to the circuit has
clearly been turned OFF before installing the
product. In some countries, electrical installation
must be carried out by authorised electricians/
contractors; please check with your local
authority for guidance.
The product must not be modified in any way.
HAY accepts no responsibility for any products
that have been modified or tampered with. The
external flexible cable or cord of this luminaire
cannot be replaced. If the cord is damaged,
the luminaire should be replaced. This lamp is
designed for indoor use only.
CARE AND MAINTENANCE
The product can be cleaned with a soft damp
cloth and mild detergent, or a dry microfibre
cloth. Do not use alcohol or any other solvents
to clean the product and avoid using abrasive or
rough sponges. Ensure that the power supply has
been turned OFF before cleaning the product.

 PARTS 
Wall plugs Screws Allen key
Lamp
Adapter Power supply
Handle

1.
Unpack all the parts and check that you have received all the parts listed.
The arm has three different settings allowing for different degrees of freedom
in a vertical direction. Choose the setting most suitable for your needs.
Side views
Setting 2
Setting 1
Setting 3 (default)
30°
5°
30°
10°
17.5°
17.5°

2.
If you would like to change between the three different settings for the arm -
simply loosen the screw on the adjustment slider (step 1), change the slider’s
position (step 2) to the setting you require (step 3) and aligning the screw with
the pre-defined hole and tighten the screw. It is suggested that two people
carry out this step.
Step 1
Step 2
Step 3
Setting 1
Setting 1
Setting 1
Setting 2
Setting 2
Setting 2
Setting 3
Setting 3
Setting 3

3.
The head of Fifty-Fifty Wall is flexible and can be moved sideways and up and
down. The arm also allows for a 180 degree horizontal movement.
50°
50°
Side view Front view
90°
90°90°
90°
Top view

4.
Using the lamp’s wall bracket as a guide, mark the position of the holes to be
drilled (640 mm apart). Use a spirit level to ensure that the wall bracket is level.

5.
Drill the holes using the correct type of drill for the wall you are drilling into.

6.
Insert the wall plugs. Ensure you use the correct type of plugs for the type of wall.

7.
Fix the wall bracket onto the wall using the provided screws, starting from the top.

8.
Screw the handle into the head, ensuring it is tight before using it to
adjust the lamp’s position. The lamp can be freely moved and will hold
in any position. A touch sensitive step dimming switch is located on the
backside of the lamp’s head.

9.
Plug the trailing cable into the power supply.
Attach the correct adapter for your region.
The lamp is now ready for use.

 CARE & MAINTENANCE 
Our Care & Maintenance offers guidance for optimal
maintenance of your HAY product. It includes advice
and instructions on cleaning and caring for specific
materials to prolong the life of your lighting.
Please find our Care & Maintenance
guide by scanning the QR code
You can find more relevant information on
Fifty-Fifty Wall by scanning the QR code
You can also find the same information here
hay.dk/downloads

14102021
Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
www.hay.com