Hay T12 User manual

INSTRUCTION MANUAL
T12
By HAY

INTRODUCTION
Defined by its pure functionality, HAY’s T12
Table serves as a dining or work table in a tight
composition and a clear aesthetic. Fundamental
to the table’s design are the legs, which are
positioned in the corners to seat as many people
as possible, and the generous size which offers
optimal working space. These factors make it
particularly suitable for using in meeting rooms
or as a dining table for larger families.

CARE AND MAINTENANCE CARE AND MAINTENANCE
CAUTION
With a little care you can prolong the life of your
furniture. Follow the instructions for the materials of
your specific product to make sure that it stays in
the best shape for as long as possible.
The information below is only intended as a general
guideline. For more information on how to remove
specific stains, please enquire where you bought
the furniture.
• Always remove stains quickly before they can do
any permanent damage to the furniture.
• Avoid placing the furniture in direct sunlight or near
a strong heat source to reduce changes. As linoleum
is a natural material, it will change in colour and will
patinate over time.
• When you move your furniture, make sure you lift it
rather than pulling or pushing it to avoid damaging
the floor, legs and mountings.
• Tighten up the screws after one to two months’
use and whenever required.
• Avoid improper use such as putting your feet
on the table or standing on it.
• Use coasters under damp, hot or coloured
objects to avoid permanent stains.
• Avoid partially covering the surface, for example
with tablecloths or place mats, as colour variances
may appear.
• Be careful not to scratch or damage the
surface with sharp objects.
LAMINATE
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• Stains may be carefully removed using household
ammonia or with a clean, damp cloth or a nano sponge
wrung in warm water. Never use the nano sponge dry.
Follow up immediately with a clean, dry cloth.
• Avoid using scouring cream or scouring pads,
as they may scratch the surface.
LINOLEUM
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent or soap
flakes. Remove soap residue immediately using a
clean, dry cloth.
• If the surface is scratched or appears matt, use
a care product especially suited to linoleum.
• Stains may be carefully removed using white spirit
(mineral spirit) or a damp nano sponge dipped in
lukewarm water or linoleum care product. Follow up
immediately with a clean, dry cloth. Never use the
nano sponge dry.
• Avoid alkaline detergents such as soft (yellow)
soap, washing soda, lye and scouring powder.
POWDER COATED ALUMINIUM
• Wipe with a clean cloth wrung in water or in a
solution of water and a neutral detergent. Remove
soap residue immediately using a clean, dry cloth.
• Avoid using scouring cream or scouring pads,
as they may scratch the surface.

CONTENTS
PAGE 08 - 17
L160 / L200 / L250 cm
PAGE 18 - 30
L320 / L400 cm

A X 1
B X 2
F X 4
C X 2
G X 1
D X 4
H X 1
K X 16
L 160 x W 80 / L 200 x W 95 / L 200 x W 120
L 250 x W 95 / L 250 x W 120 cm
INSTRUCTION
MANUAL
E X 4
I X 1
J X 16
(J X 20 / W 120cm)
PARTS

1.
While assembling, keep the table inside the cardboard box with foam edge in order to protect
the tabletop from scratches etc. Make sure that all parts are included.
2.
Slide the F part into the D part.
Repeat this step for all 4 x D parts.

2.
Screw the E part onto the D part, using the G part.
Repeat this step for all 4 x E parts.
3.
Place B and C parts into the E part.
Repeat this step for all 4 x E parts.

4.
Screw 4 x K parts using the I part.
Repeat this step for all 4 x E parts.
5.
Place the tabletop (A) on top of the frame.

6.
Screw the C, D and E parts onto the J part, using the H part.
7.

L 320 x W 95 / L 320 x W 120
L 400 x W 95 / L 400 x W 120
INSTRUCTION
MANUAL
A X 1 (A x 2 / L400 cm)
C X 2
G X 6
D X 6
H X 1
L X 24
B X 4
F X 2
E X 4
I X 1
K X 32
(I X 36 / W 120cm)
M X 1
J X 1
PARTS

1.
Slide the G part into the D part.
Repeat this step for all 6 x D parts.
2.
Screw the E part onto the D part, using the H part.
Repeat this step for all 4 x E parts.

3.
Place B and C parts into the E part.
Repeat this step for all 4 x E parts.
4.
Screw 4 x L parts using the J part.
Repeat this step for all 4 x E parts.

.5.
Screw the F part to the D part, using the H part.
Repeat this step for both F parts.
6.

7.
Place the M part in the F parts and tighten the bolt.
Repeat this step for both F parts.
8.
Screw 4 x L parts using the J part.
Repeat this step for both F parts.
A WRENCH IS REQUIRED
TO COMPLETE THIS STEP

9.
Place the tabletop ( A ) on the frame
10.
Screw the C, D and E parts onto the K part to the A part using the I part.
Please be aware that the L400cm
tabletop is split in two.

11.
Please use a rubber head
hammer or similar tool.
DISASSEMBLE
Please note: when disassembling the table, loosen the screws, bash firmly on the screw with a
rubber head hammer or something similar that will not break the screw, and pull the leg.

Havnen 1 8700 Horsens Denmark
[phone] / [e-mail]
ITEM NO. 706354
710441 2458725
30082017