Teknik 5420277 User manual

Industrial Style 4 Shelf Bookcase
Model 5420277
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
Show everyone how
smart you are.
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Assembly Steps
Safety
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
2
4-8
13
Page 2
Electric drill with 1/4" bit
(ONLY in indicated step)
Rubber Mallet

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A TOP (1)
B UPPER SHELF (1)
C SHELF (3)
D UPPER END (2)
E LOWER END (2)
F SHELF SUPPORT (10)
Page 3
A
B
C
D
E
F
F
D
E
C
C
F
F
F
F
F
F
F
F

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
ALLEN WRENCH - 1
8
1-3/8" ALLEN SCREW - 20
11-1/8" SCREW - 20 21/2" ALLEN SCREW - 8 3
FURNITURE TIPPING RESTRAINT KIT - 1
99
Page 4

Step 1
å Assemble your unit on a carpeted floor or on the empty carton to avoid scratching your unit or the floor.
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
å Insert the LOWER END (E) into the UPPER END (D).
å Then, fasten the UPPER END (D) to the LOWER END (E). Use four 1/2" ALLEN SCREWS (3) and the ALLEN WRENCH (8).
å Repeat this step for the other ENDS (D and E).
D
E
1/2" ALLEN SCREW
(8 used in this step)
3
D
E
8
Page 5

Step
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
å Fasten the ENDS (D and E) to the SHELF SUPPORTS (F). Use twenty 1-3/8" ALLEN SCREWS (1) and the
ALLEN WRENCH (8).
å NOTE: Be sure to square up the SHELF SUPPORTS (F) to the ENDS (D and E) before you completely tighten
the SCREWS.
Step 2
Page 6
8
D
E
D
E
F
F
F
F
F
F
FF
F
F
1-3/8" ALLEN SCREW
(20 used in this step)
1

Step
Page 7
å NOTE: You should start each SCREW a few turns before completely tightening any of them.
å Fasten the TOP (A) and SHELVES (B and C) to the ENDS (D and E). Use twenty 1-1/8" SCREWS (2).
å NOTE: The TOP (A) is larger than the SHELVES (B and C). The UPPER SHELF (B) is finished on both sides. Be sure to
position these parts exactly as shown in the diagram below.
å NOTE: Do not overtighten the SCREWS.
Step 3
1-1/8" SCREW
(20 used in this step)
2
D
E
D
E
A
B
C
C
C
Surface with holes
Surface with holes
Unfinished
surface
Unfinished
surface
Unfinished
surface

Step 4
Page 8
25 lbs.
30 lbs.
30 lbs.
30 lbs.
30 lbs.
99
Use the 5/8" screw through the
small hole in a bracket and into
the back edge of the TOP (A).
Small hole
å Carefully stand your unit upright.
å We recommend using the FURNITURE TIPPING RESTRAINT KIT (99) for added stability. Fasten a bracket to the back
edge of the TOP (A) using the 5/8" screw as shown.
å Place your unit in its final location against a wall.
å Follow the instructions included in the KIT to fasten your unit to the wall.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with your favorite furniture polish or a damp cloth. Wipe dry.

Page 13
WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Overloaded shelves.
• Improper loading can cause the
product to be top-heavy.
• Risk of injury.
• Top-heavy furniture can tip over.
• Overloaded shelves can break.
• Never exceed the weight limits shown in
the instructions.
• Work from bottom to top when loading
shelves. Place the heavier items on the
lower shelves.
• Improperly moving furniture that is not
designed and equipped with casters. • Furniture can tip over or break if improperly moved.
• Physical injury. Furniture can be very
heavy.
• Unload shelves from top to bottom before
moving the furniture.
• Do not push furniture, especially on a
carpeted floor. Have a friend help you lift
the item and set it in place.
• This unit must be positioned against a
wall.
• Children climbing on the shelves can
cause the product to tip. • Risk of injury or death. • Do not allow children to climb on the shelves. Avoid placing items like toys or
candy on upper shelves.
•Use the supplied tipping restraint kit for
added stability.
• Placing TVs on furniture items that are
not designed to support a television is
hazardous.
• Risk of injury or death. TVs can be very
heavy. Plus the weight and location of the
picture tube tends to make TVs unbalanced
and prone to tipping forward.
• This product is not designed to support a
television.