Health O Meter Pro Series User manual

Health o meter

ASSEMBLY INSTRUCTIONS
This 595KL scale comes completely assembled and
ready to use. However, four (4) screws have been
installed from the underside of the scale to lock the twin
load beams and prevent damage to the beams during
shipment. These locking screws must be removed
before using the scale.
■ TO REMOVE;
1. Put both arm rests on the chair scale in the up
position. Fold the footrest up.
2. Slowly tilt the chair scale completely forward until the
scale is upside down and resting on the upper edge
of the back and forward edge of the seat.
3. Notice that in each corner of the channel base is a
slotted hex head screw, which is screwed from the
underside into the flange supporting the load beams.
(Fig 1)
4. Using a 3/8* wrench, remove all four (4)-!ocking
screws. DO NOT DISCARD THESE SCREWS
SINCE THEY CAN BE REINSTALLED IF THE
SCALE NEEDS TO BE RESHIPPED.
5. Return the scale to its upright position.
HEX HEAD SCREW
FIG. 1
SETUP
1. Connect the scale to power outlet or battery.
Charge scale 24 hours before use.
2. The scale will check for the level of battery every 3
minutes. If the battery has less than 6 volts but
greater than 5.5 volts, the scale will display the
warning message "LOW BAT”.
3. N ote; do not operate or calibrate the scale if the
battery voltage is less than 5.5 volts. With less than
5.5 volts, the scale cannot display the “LOW BAT*
■ w arning and wil! not function properly. To check the
scale voltage, press the BATTERY button.
BATTERY CHARGING
The rechargeable battery used in this scale is similar to
the ..no-maintenance lead-acid batteries used in
automobiles. No maintenance means that since the
battery is sealed, no checking of water level or adding of
water to the battery is necessary. However, recharging
at proper intervals and proper storage procedures are
necessary, as in the automobile battery.
A fully charged battery will provide a month of normal
weighing before requiring recharging. When flashing“
LOW BAT" appears in the upper center portion of the
display during a weighing, the battery needs to be
recharged.
TO CHARGE THE BATTERY
1. Insert the plug of the battery charger cord into the
jack on the battery housing located at the rear of the
scale.
2. Plug the battery charger into a 120 VAC outlet
3. The battery will fully charge in 24 hours. The scale
may be used while the battery is charging, but it may
not be calibrated unless the battery is fully charged.
Note; The battery cannot be overcharged with the
specially designed charger furnished with this scale. Do
not use any other charger or adapter otherwise serious
damaged to the scale or battery can result.
Optimum battery life will be obtained if the scale is
operated and stored connected to 120 VAC.
If the scale is not connected to 120 VAC and is to be
stored for an extended period of time, it should be stored
with a fully charged battery, preferably in a cool place.
The battery should be recharged as soon as possible or
its useful life will decrease significantly. A discharged
battery left in the scale can leak and cause permanent
damage to the battery and scale.
SCALE SPECIFIATIONS
Capacity: 400 lb. x % lb.
181.4 kgs. X .1 kg.

OPERATION INSTRUCTIONS
TROUBLE SHOOTING
General
For safer scale transport and easier patient seating, the
scale has a foot rest which folds up out of the way.
Once the patient is seated, the footrest can be folded
back down for patient comfort and safety.
Scale Use
Buttons
START Allows weighing to take place by starting scale
•TARE Converts display to zero
LB Converts display to pounds
KG Converts display to kilogram
BATT Converts display to battery voltage
select kg
T. Push the START button to turn the scale on.
2. The LCD will display —, and then 0 LB and emit 1
beep, indicting the scale has set its zero (tare) point,
and is ready for weighing.
3. To change the weighing mode, press the LB or KG
button.
4. Place the child or adult in the chair. The scale will
display after the weight has stabilized, the scale
will give three beeps and the LCD display will show
the weight reading.
5. The weight will remain on the display for 2 min. or
until the TARE button is pressed. If the scale has no
activity within 5 minutes, it will enter into a dormant
state. In the dormant state, display will be blank.
Scale does not work correctly:
1. Be sure shipping screws have been removed.
2. Check battery voltage when the charger is not
plugged into the battery. The battery must have a
charge of 5.5 to function correctly.
3. Check the fuse has not blown. The fuse is located
in the battery pack, incased in the fuse housing.
4. Check the scale is on a level, hard surface.
5. ERRH message: Scale senses a zero point higher
than expected, Check that additional weight is not
on the platform and press TARE.
6. ERRL message: Scale senses a zero point lower
than expected. Check that the seat assembly, or
tray are installed and press TARE.
OL message: Scale has exceeded the capacity.
CALIBRATION PROCEDURE
NOTE: Only calibrate the scale with certified 300 lbs.
weights or by a qualified lab or technical center. Charge
scale for 24 hours before starting the calibration steps.
1. Remove the plastic back rest for easy access to the
back of the scale head.
2. Remove the access cover on the back of the scale
head labeled “Remove to calibrate”.
3. Set the jumper (there is only one jumper, located in
the back of the head) by lifting the cap off the left
and middle pin and replacing it connecting the right
and middle pin.
4. Push the START button the screen will show "0 LB”.
Make sure there is no weight on the platform
5. Push the TARE button, the screen will show
11 U L OAD" briefly followed by “OLOAD”.
6. Place a certified dead weight of 300 lbs. on the scale
platform.
7. After the weight is placed on the platform and
stabilized, press TARE button again and the screen
will display a raw count briefly, followed by “LD-TL .

8. After the short beep, press the TARE button again,
and “CAPA" will show on the screen.
9. Another short beep will sound (or wait 10 seconds);
press the TARE button again and the screen will
display the amount the scale is currently weighing.
10. Place the jumper back in the left position to accept
the calibration and finish the procedure. Replace
the access cover removed in Step #2.

1
63798
Pillar Assembly
13
63735
Cover, Head Shell
2 23055
7-19 x Vs Plated Screw
14
23048
6*32 x 7-s Round Head Screw
3 23175
10-16 x 5 to Hex Head Screw
i 3
SG-07 Electronic Board
4
63727
Yoke
15
63716
Instruction lade!
5
63372
Yoke insert
17
Swivel Plate Assembly
6
63725 Head Shell
18
Dome Switch Board
7
63332
End Cap
19
23271
Snap Rivet
8
63704
End Cap Insert
20
63715
Dome Switch Sutton
9 23155 10-24 x vs Locking Screw 21 23227
’to-20 x */2 Slotted Hex Head Screw
10 64706
Nameplate
22
23226 Locknut
11
23038 6-32 x 3 to Round Head Screw 23
63726
Swivel Bracket
12
63702 Support. Nameplate
24
64718 Pillar Cable Assembly

232 ;s/
It external Tooth Lock Washer
63310
647S
Terminal Board Assembly
83 /
Jaffa ry Housing
12 64746 Base Asssmdy (Frame Only) 25 23151 10-24 x \U Hat Head Screw
13 23122 10-24 x T /<5 Round Head Screw I 26 63706 Battery Housing Namepiais

Peistar LLC warrants that for a period of five years front the date of purchase, this product will be free from
defects in material and workmanship. Peistar, at its option, will repair or replace this product or any
component of the product found to be defective during the warranty period. Replacement will be made
with a new or remanufactured product or component. If the product is no longer available, replacement
may be made with a similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original purchaser from the date of initial purchase and is not transferable.
Peistar dealers or retail store outlets selling Peistar products do not have the right to alter, modify or in any
way change the terms and conditions' of this warranty.
The warranty does not cover normal wear of parts or damage resulting from negligent misuse of the
product. Further, the warranty does not cover Acts of God, such as fire, flood, and tornadoes.
Peistar shall not be liable for any incidental or consequential damages caused by the breach of an express or
Implied warranty or condition. Except to the extent prohibited by applicable law, any implied warranty of
merchantability or fitness for a particular purpose is limited in duration to the duration of tne above
warranty. Peistar disclaims all other warranties or conditions, express or implied statutory or otherwise.
Some provinces or jurisdictions do not allow the exclusion, or limitation of incidental or consequential
damages or limitation on how long an implied warranty lasts, so the above limitation or exclusion may not
■ apply to you. This warranty gives you specific legal rights and you may also have other rights that vary
I from state to state or province to province.
How to Obtain Warranty Service
Call (BOO) 638-3722 to obtain a Return Authorization for warranty service. Then, send the product with
proof of purchase included. Ship with freight and insurance prepaid to:
Peistar LLC
Attn: RAH _ _
7400W. 10CF Place
Bridgeview. IL 60455
j
j Make certain that your scale is properly packed to avoid damage in transit to the factory. If your scale Is
| not covered by warranty, or has been damaged, an estimate of repair cost will be provided to you for
1 approval prior to serving or replacing.
A Product of Peistar LLC
7400 w. 100 th Place
Bridgeview, IL 60455
Health o meter is a register trademark of Peistar LLC.
Customer Service:
Technical Service l Returns:
Tech Service / Customer Service FAX:
[phone]
[phone]
[phone]