Heat Outdoors Shadow User manual

Industrial heaters - 230v 3kw ,4kw and 6kW models
Product manual
Heat Outdoors
Unit 9, Stort Valley Industrial Estate
Stansted Road, Bishop’s Stortford
Hertfordshire, United Kingdom
CM23 2TU
www.heat-outdoors.co.uk
01279 466500
[email protected]

Brief Introduction
Shadow industrial and warehouse infrared heaters combine the marketed leading Ultra Low Glare
infrared lamp technology, with advanced outer casing construction, allowing us to achieve up to
18kW of short-wave infrared heat.
Infrared industrial heaters offer an ideal alternative to traditional gas or blown heating systems. The
direct short-wave infrared emitted heats people and objects. They efficiently heat specific areas of
wide open commercial and industrial spaces. They can be used to heat workbenches, packing
desks and workstations. Minimising the need to waste energy heating the whole space.
Important Safety Instructions - Read all instructions before using this heater
When using electrical appliances, basic safety precautions should always be followed to reduce the
risk of fire, electric shock, or injury to persons, etc.
Read through the operation and assembly instructions conscientiously before operating the
appliance.
Be sure to keep the manual in a safe place for future reference. If you pass the appliance on, pass
on the instructions too.
• Check if the voltage indicated on the nameplate of the appliance corresponds to the local mains
voltage before you connect the appliance.
• The power supply to the appliance should correspond to the relevant regulations of the power
supply companies and the regional construction regulations. Extension cords and multi-sockets
may be used only if care is exercised in their use. The marked electrical rating of the extension
cord or multi-socket should have adequate current carrying capacity and correspond to the
relevant regulations of the power supply companies and the regional construction regulations.
Check if the voltage indicated on the appliance corresponds to the marked electrical rating of the
extension cord or multi-socket before you connect the appliance.
• The appliance is not located immediately below a wall socket-outlet.
• Never install this appliance close to anything combustible material, such as furniture,
curtains, etc.
•In order to avoid overheating and fire hazard, do not cover or obstruct the appliance. Do not put
any of the following materials on the appliance, such as clothes, blanket, pillow, paper etc.
• The casing and the front cover of the appliance become extremely hot during operation. Pay
attention that, no combustible material due to Wind or other environmental influences covers or
obstructs the appliance, such as curtains, marquees, flags, plastic foil etc. Do not touch the
appliance. Caution! Risk of scald injury!
•Do not let the cord hang over edge of table or counter, or touch hot surfaces.
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
•In case of improper use, there is a risk of electrical shock and/or fire hazard. Operation of the
appliance must be discontinued and remove the mains plug immediately. Do not try to repair the
appliance by your-self. Please contact with the service agent or a suitably qualified electrician for
maintenance.
•Remove the plug from the power outlet and wait until the appliance is sufficiently cooled off
before cleaning.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their
safety.

• Keep out of reach of children. In order to keep children from the dangers of electrical appliances,
never leave them unsupervised with the machine. Consequently, when selecting the location for
your machine, do so in such a way that children do not have access to the machine. Children
being supervised not to play with the appliance.
•The appliance must only be mounted by an authorized specialist, paying attention to the relevant
regulations of the power supply companies and the regional construction regulations.
•Do not use this heater with a programmer, timer, separate remote-control system or any other
device that switches the heater on automatically, since a re risk exists if the heater is covered or
positioned incorrectly.
•– the reguard of this heater is intended to prevent direct access to heating elements and must
be in place when the heater is in use;
•– the reguard does not give full protection for young children and for inrm persons.
Installation
For additional protection the installation of a residual current device (RCD) is advisable.
•Remove all package material (including anti-vibration object of the lamp) and check the
appliance, supply cord and the plug for signs of damage.
• Pay attention to the mounting place and all mounting material(dowels, screws). Ensure they are
suitable and stable enough for mounting and lastingly holding of the appliance.
•Before mounting, the minimum safe mounting distances and tilt angles shown in the figures
must be strictly followed:
1. The distance between the bottom edge of the appliance and the floor must be at least 2.5M
(3.0M for the 6kw version).
2. There must be a distance of at least 0.5 M between the appliance and the ceilings, roofs or
other covers.
3. There must be a distance of at least 1.0 M (1.5M for the 6kw version) at each side between
the appliance and adjacent walls. See figure 2.
4. Remember that degree to mounting surface is 45° when wall mounted. Figure 3
• Pay attention that, the installation of the appliance must not add excessive wind load.
•Fix the mounting bracket on the wall first. Ensure that the place to be installed is secure and firm.
•The heaters are also widely used hung from the ceiling. When ceiling mounted the heaters are
more efficient if mounted at a slight angle of between 10-20° to create better heat distribution.
•Adjust the desired angle of radiation and fest screw all screws. Check regularly the screw’s
connection. Mechanical bearing pressure and oscillation could lead to loosen the fittings.
•Plug in the power source. Then observe, whether during the first 10-15 minutes the appliance
works trouble-free. Unplug from the power outlet and wait until the appliance is sufficiently
cooled off before cleaning.

Specification of the Shadow Industrial heater range
Figure 1: Mounting bracket
(wall bracket) and anchor dowels
provided. Connection from the
wall to the infrared heater.
Figure 2: Min. distance to oor,
ceiling and wall.
Figure 3: Tilt angle.
903672 918kW 16 110 520.5 129.2
903672-15 9 13.5kW 16 110 520.5 129.2
903671-15 69kW 14 110 390 129.2
903671-15 612kW 14 110 390 129.2
903670-15 23kW 6.1 110 250.5 85.7
903670-15 2 4kW 6.1 110 250.5 85.7
903673 3 6kW 8.2129 255 110
Code Number of
lamps Watts Weight
(kg) H (mm) W (mm) D (mm)
Volts
380 -
415V
380 -
415V
220 -
240V
220 -
240V
380 -
415V
380 -
415V
220 -
240V
Cleaning and maintenance
• This appliance is consist of a robust and maintenance-free aluminum casing. No user
serviceable parts inside.
•Before cleaning, remove the plug from the power outlet and wait until the appliance is sufciently
cooled off.
• Wipe the appliance only with clean and lint-free cloth or a soft brush.
• Never use abrasive cleaners, scrubbing brushes and chemical cleaners for cleaning!
•The alcohol can be used to clean the appliance. When cleaning the reector, please contact with
the service agent or a suitably qualied electrician if the reector needs to be removed.

• To protect against electrical shock and danger of life, do not immerse cord, plug, or any part of
the appliance in water or other liquid.
• For heating element replacement ,please contact the manufacturer or its service agent or a
similarly qualied person.
Disposal
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe recycling.
Customer service
Repairs must be carried out by authorize specialists, thus ensuring electrical safety. Please contact
with the service agent or a suitably qualied electrician.
Improper repairs could lead to danger to the user.
This warranty does not cover damage of failure which results from alteration, accident, misuse,
abuse, neglect, commercial use or improper maintenance.
In line with our policy of continuous product development we reserve the right to change the product
and documentation specications without notice.

Heat Outdoors
Unit 9, Stort Valley Industrial Estate Stansted
Road, Bishop’s Stortford Hertfordshire, United
Kingdom CM23 2TU
www.heat-outdoors.co.uk
01279 466500
[email protected]