Heath Zenith SL-7464-03 User manual

This chime requires 3 “C” alkaline batteries (not included). In typical use,
alkaline batteries will last up to 2 1/2years.
Wireless Chime
© 2017 HeathCo LLC
Figure 1
WARNING: To prevent possible
SERIOUS INJURY or DEATH:
• NEVER allow small children near
batteries.
• If battery is swallowed, immediately
notify doctor.
This package includes (Style of door sensor and chime may vary from illustration):
1. Remove orange battery tab from push
button. Remove back of case by pushing in
tab on bottom with a small screwdriver (see
Figure 1). Remove orange battery tab.
2. Install 3 alkaline “C” batteries (not includ-
ed) into chime base. Make sure batteries are
installed according to the diagram inside the
chime (see Figure 2).
IMPORTANT:To avoid resetting chime base
memory, wait 30 seconds before pressing
push button.See Troubleshooting, Problem
3if chime memory was accidentally reset.
C
H
I
M
E
V
O
L
U
M
E
3x - “C” TYPE BATTERIES
TYPE “C”
TYPE “C”
TYPE “C”
PRESS & HOLD TUNE–1 SEC SYNC–3 SEC RESET–10 SEC
Figure 2
Chime base Chime cover Wireless push
button
Hardware
pack
Model
C
H
I
M
E
V
O
L
U
M
E
3x- “C” TYPE BATTERIES
PRESS&HOLD TUNE–1SEC SYNC–3SEC RESET–10SEC
7611 ✔ ✔ ✔ ✔
7464 ✔ ✔ ✔ ✔

2
3. Test range. Temporarily position chime and
push button where you want them mounted.
Press push button to verify chime and push
button work properly (see Figure 3). If chime
does not sound, see Troubleshooting.
4. Adjust volume control. Turn volume control
knob on chime base to adjust volume.
5. Mount push button. Use either screws or
double sided tape to mount push button.
• Screw Mounting: To mount with screws,
remove back of case by pushing in tab
on bottom with a small screwdriver (see
Figure 1). Note: Remove material in screw
holes (if needed) before mounting with
screws. Attach back of case to door jamb
or wall (see Figure 4). Snap front of push
button on.
• Tape Mounting: When attaching push but-
ton using double-sided tape, make sure the
surface of the door jamb or wall is clean.
6. Rotate cover pin. Before mounting the chime
base to the wall, turn the base vertically or
horizontally (depending upon the chime cover)
and slide the cover pin out of the chime base.
Turn the pin over and slide the cover pin into
the chime base (see Figure 5).
7. Mount chime base. Using the “UP” arrow
indicator, place the chime base against the
wall and make sure it is level. Mark the four
screw hole locations on the mounting surface
(see Figure 6).Drill four 3/16 in. pilot holes and
insert wall anchors. Align the four screw holes
in the chime base with the wall anchors and
insert the four M3 x 30 mm screws. Tighten
securely.
8. Hang the chime cover on the cover pin on
the chime base.
Figure 4
Figure 3
Figure 5
Figure 6
C
H
I
M
E
V
O
L
U
M
E
3x - “C” TYPE BATTERIES
TYPE “C”
TYPE “C”
TYPE “C”
PRESS & HOLD TUNE–1 SEC SYNC–3 SEC RESET–10 SEC
C
H
I
M
E
V
O
L
U
M
E
3x - “C”TYPE BATTERIES
TYPE “C”
TYPE “C”
TYPE “C”
PRESS& HOLD TUNE–1SEC SYNC–3SEC RESET–10SEC

3
Tune Settings
Tune Setting Table
The chime has different selectable tunes: Ding
(one note tune), Ding-Dong (two note tune), or
Westminster (eight note tune). The factory set-
ting is for the Westminster tune. This tune can
be changed by following the instructions in the
Tune Setting Table.
Note: All chime models are designed to work with
up to 5 push buttons (sold separately).All chimes
are designed to play only two different tunes no
matter how many push buttons are used.
Chime Base
Inside Push Button
C
H
I
M
E
V
O
L
U
M
E
3x - “C” TYPE BATTERIES
TYPE “C”
TYPE “C”
TYPE “C”
PRESS & HOLD TUNE–1 SEC SYNC–3 SEC RESET–10 SEC
Push Button Chime Tune
Jumper - ON ——— Ding
Jumper - OFF Press and release button on chime.
Listen for selected tune. Repeat to
select different tune.
Ding-Dong or
Westminster

4
Troubleshooting
1. PROBLEM: Chime does not sound or rang one time and quit.
A. POSSIBLE CAUSE: Push button and chime are not synced.
A. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
B. POSSIBLE CAUSE: Batteries not installed correctly.
B. CORRECTIVE ACTION: Make sure batteries are installed according to
the diagram inside the push button and chime.
C. POSSIBLE CAUSE: Batteries are dead.
C. CORRECTIVE ACTION: Check charge of push button and chime bat-
teries and replace if necessary.
2. PROBLEM: Batteries seem okay, but the chime does not work after instal-
lation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near
metal studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims
to move chime or push button away from metal surface.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall.Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wire-
less device.
CORRECTIVE ACTION: Reset chime.
• Remove push button battery. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the button on the chime until the chime sounds a
“Beep-Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the button on
the chime until the chime sounds a “Beep-Beep”.

5
• Press the push button within 30 seconds. The chime will sound a
“Beep-Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
Note: The push button and chime come synced from the factory. The range of
the wireless chime can vary with location, temperature, and battery condition.
Learn more about home shop we have.