Heath Zenith 7311 User manual

Wireless Chime
© 2019 HeathCo LLC 209939-01A
1. Remove orange battery tab from push button.
Remove back of case by pushing in tab on bottom
with a small screwdriver (see Figure 1). Remove
orange battery tab.
2. Plug in wireless chime (see Figure 2).
3. Test range. Temporarily position chime and push
button where you want them mounted. Press push
button to verify chime and push button work prop-
erly. If chime does not sound, see Troubleshooting.
Figure 1
Figure 2
WARNING:To prevent possible SERIOUS
INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify
doctor.
This package includes (Style of push button and chime may vary from illustration):
Model
Wireless
chime
VOL+VOL–Light Sync
Music
Wireless push
button Hardware pack
7311 ✔ ✔ ✔
VOL+VOL–Light Sync
Music

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
2
4. Mount push button. Use either screws or double
sided tape to mount push button.
• Screw Mounting: To mount with screws, remove
back of case by pushing in tab on bottom with a
small screwdriver (see Figure 1). Note: Remove
material in screw holes (if needed) before mounting
with screws. Attach back of case to door jamb or
wall (see Figure 3). Snap front of push button on.
• Tape Mounting: When attaching push button
using double sided tape, make sure the surface
of the door jamb or wall is clean.
Operation
Chime Mute
The chime can be muted for a select period of time:
full-time, 3 hours, 6 hours, 9 hours, or 12 hours. Press
and release the mute icon to select the amount of time
the chime should be muted (see Figure 4). The mute
icon will turn green each time it is pressed to show the
amount of time selected.
Figure 4
Figure 3
OFF Full-Time 3Hr 6Hr 9Hr 12Hr
Note: The chime will flash the selected color each
time the push button is pressed whether the chime is
muted or unmuted.

3
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
Tune Setting Table
Push Button Tune
Switch 2 - ON (Back Door) Ding
Switch 2 - OFF (Front Door) Selected Musical Tune
Volume Control
The chime has adjustable volume levels. Press and
release the “VOL +” or “VOL –” buttons to increase or
decrease the chime volume.
Light Color Selection
The chime will blink whenever the push button is
pressed.The color of the light is selectable. Press and
hold the “Light” button until the chime glows.While the
chime is glowing, press and release the “Light” button
to select the desired color. Press the push button to
lock in the desired color.
Tune Selection
The chime has ten pre-loaded selectable “front door”
tunes. Press and release the “Sync/Music” button until
the desired tune is heard.While the desired tune is play-
ing, press the push button to lock in the selected tune.
Note: Each push button can be assigned its own
unique tune.
Note: To listen to the selected tune, press and release
the “Sync/Music” button.
Note: All chime models are designed to work with up
to 5 push buttons (sold separately).
VOL +VOL –Light Sync
Music
VOL +VOL –Light Sync
Music
VOL +VOL –Light Sync
Music
Tune Selection Guide
Front Door
Ding-Dong Birthday Celebration
Traditional Westminster Auld Lang Syne
Traditional Whittington Beethoven’s 5th
Bell Whittington We Wish You a Merry Christmas
Short Westminster Star Spangled Banner
Back Door
Ding
ON
1 2

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
4
Troubleshooting
1. PROBLEM: Chime does not sound or rang one time and quit.
A. POSSIBLE CAUSE: Push button and chime are not synced.
A. CORRECTIVE ACTION: Sync the push button and chime.
• Press and hold the “Sync/Music”button on the chime until the chime sounds
a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a “Beep-
Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
B. POSSIBLE CAUSE: Push button battery is not installed correctly.
B. CORRECTIVE ACTION: Make sure battery is installed according to the
diagram inside the push button.
C. POSSIBLE CAUSE: Push button battery is dead.
C. CORRECTIVE ACTION: Check charge of push button battery and replace if
necessary.
D. POSSIBLE CAUSE: Chime is not receiving power.
D. CORRECTIVE ACTION: Make sure the plug-in chime has power.
E. POSSIBLE CAUSE: Chime is muted.
E. CORRECTIVE ACTION: Press and release the mute button until the green
light is turned off.
F. POSSIBLE CAUSE: Dip switch #1 in the push button has been moved to the
“ON” position.
F. CORRECTIVE ACTION: Ensure dip switch #1 is in the “OFF” position in the
push button and follow the steps above to re-sync the push button and chime.
2. PROBLEM: Push button battery seems okay, but the chime does not work after
installation.
A. POSSIBLE CAUSE: Chime or push button is mounted on metal or near metal
studs. Note: Metal reduces transmission range.
A. CORRECTIVE ACTION: Use 1/4 in. to 1/2 in. (6 to 13 mm) wood shims to
move push button away from metal surface. Move chime to a different wall
outlet.
B. POSSIBLE CAUSE: Chime is mounted near concrete floor or wall. Note:
Concrete may reduce range.
B. CORRECTIVE ACTION: Move chime away from concrete surface.
C. POSSIBLE CAUSE: Chime and push button are installed too far apart.
C. CORRECTIVE ACTION: Locate chime closer to push button.

5
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
3. PROBLEM: Chime sounds when not intended (false triggers).
POSSIBLE CAUSE: Chime is receiving interference from another wireless
device.
CORRECTIVE ACTION: Reset chime and push button.
• Remove push button battery. Wait 30 seconds.
• Press and hold the push button for 10 to 15 seconds within 60 seconds
after installing battery into the push button.
• Press and hold the “Sync/Music”button on the chime until the chime sounds
a “Beep-Beep-Beep-Beep”.
• To re-sync the push button and chime, press and hold the “Sync/Music”
button on the chime until the chime sounds a “Beep-Beep”.
• Press the push button within 30 seconds. The chime will sound a “Beep-
Beep” tone to indicate the push button is synced.
• Press the push button to ensure operation.
4. PROBLEM: The new push button and chime do not work with existing push
buttons and chimes.
POSSIBLE CAUSE: The new push button and chime are not using the same
codes as existing push buttons and chimes.
CORRECTIVE ACTION: The new push button and chime need to be set
to work with existing push buttons and chimes. Please call 1-800-858-8501
for assistance in changing the codes to work with existing push buttons and
chimes.
Note: The push button and chime come synced from the factory. The range of the
wireless chime can vary with location, temperature, and battery condition.

Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
6
Please contact us for assistance
before returning product to the
store or to HeathCo LLC.
If you experience a problem, follow this
guide.You may also contact us between
8:00 AM to 5:00 PM CST (M-F).
When contacting Technical Service,
please include the following informa-
tion: Name, Street Address, Daytime
Phone Number, Email Address, Model
Number, Date of Purchase, Place of
Purchase, Product Issue, and DATED
SALES RECEIPT FOR WARRANTY
REQUESTS.
Technical Service
No Service Parts Available for this
Product
HeathCo LLC
P.O. Box 90045
2445 Nashville Road
Bowling Green, KY 42101, USA
ATTN: Technical Service
Internet: www.hzsupport.com
Phone: [phone] (English Only)
Fax: [phone]

7
Helpful Videos – www.hzsupport.com Helpful Answers – 1-800-858-8501
HeathCo LLC reserves the right to discontinue and to change specifications at any
time without notice without incurring any obligation to incorporate new features in
previously sold products.
ONE YEAR LIMITED WARRANTY
This is a “Limited Warranty” which gives you specific legal rights. You may
also have other rights which vary from state to state or province to province.
For a period of one year from the date of purchase, any malfunction caused by
factory defective parts or workmanship will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse,
abuse or negligence, light bulbs, batteries, and other expendable items are
not covered by this warranty. Any damage to the light fixture resulting from the
use of chemicals or a pressure washer machine are not covered by this war-
ranty. Unauthorized service or modification of the product or of any furnished
component will void this warranty in its entirety. This warranty does not include
reimbursement for inconvenience, installation, setup time, loss of use, unauthor-
ized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended
to other equipment and components that a customer uses in conjunction with
our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION
OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT
FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF
ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUS-
TOMER ANDTHERE SHALL BE NO LIABILITY ON THE PART OF HEATHCO
LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES, INCLUDING BUT NOT LIMITED TO ANY LOSS OF BUSINESS
OR PROFITS,WHETHER OR NOT FORESEEABLE.Some states or provinces
do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
Please keep your dated sales receipt,it is required for all warranty requests.

Campana Inalámbrica
© 2019 HeathCo LLC 209939-01 S
1. Retire la pestaña naranja de la batería del botón
pulsador. Extraer la parte posterior de la caja pre-
sionando la aleta en el botón con un destornillador
pequeño (vea la Figura 1).Quite la aleta anaranjada
de la batería.
2. Campana inalámbrica enchufable (vea la
Figura 2).
3. Pruebe el alcance. Ponga provisionalmente la
campana y el pulsador en la posición donde los
quiera instalar. Presione el pulsador para verificar
que la campana y el pulsador funcionen apropia-
damente. Si la campana no suena, vea Análisis de
Averías.
ADVERTENCIA: Para prevenir una posible
LESIÓN SERIA o LA MUERTE:
• NUNCA deje que los niños estén cerca de las
baterías.
• Si se traga una batería, notifique inmediata-
mente al doctor.
Este paquete tiene (El estilo del pulsador y de la campana puede variar de la
ilustración):
Figura 1
Figura 2
Model
Wireless
chime
VOL+VOL–Light Sync
Music
Wireless push
button Hardware pack
7311 ✔ ✔ ✔
VOL+VOL–Light Sync
Music

9
Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
Figura 3
4. Instale el pulsador. Use ya sean tornillos o cinta
adhesiva por ambas caras para instalar el pulsador.
• Montaje con tornillos: Para montar con tornillos,
quite la parte de atrás de la caja empujando
hacia adentro la lengüeta de abajo con un
destornillador pequeño y girando la cuchilla
(vea la Figura 1). Nota: Quite la suciedad de los
orificios para tornillos (si es necesario) antes de
poner los tornillos. Coloque la parte de atrás de la
caja contra la jamba o la pared (vea la Figura 3).
Encaje a presión la parte frontal del pulsador.
• Montaje con cinta adhesiva: Cuando fije el
pulsador usando cinta adhesiva por ambas caras,
asegúrese que la superficie de la pared o la del
batiente de la puerta estén limpias.
Operación
Silenciador del timbre
La campana puede ser puesta en silencio por un
período de tiempo seleccionado: tiempo completo, 3
horas, 6 horas, 9 horas o 12 horas. Presione y suelte
el icono de silencio para seleccionar la cantidad de
tiempo que la campana debe estar puesta en silencio
(vea la Figura 4). El icono de silencio se volverá color
verde cada vez que se lo presiona para mostrar la
cantidad de tiempo seleccionada.
Figura 4
OFF Full-Time 3Hr 6Hr 9Hr 12Hr
Nota: La campana parpadeará el color seleccionado
cada vez que se presione el pulsador sea que la
campana esté o no puesta en silencio.

Vídeos prácticos – www.hzsupport.com Respuestas prácticas – 1-800-858-8501
10
Tabla de programación de melodías
Botón pulsador Ajustes
Interruptor 2 - ENCENDIDO (Puerta posterior) Ding
Interruptor 2 - APAGADO (Puerta principal) Melodía musical seleccionada
Control del volumen
La campana tiene niveles de volumen regulables
Presione y suelte los botones “VOL +” o “VOL –” para
aumentar o disminuir el volumen de la campana.
Selección del color de la luz
La campana parpadeará cada vez que se presione el
pulsador.El color de la luz es seleccionable.Presione
y mantenga presionado el botón “Light” [“luz”] hasta
que la campana se ilumine. Mientras la campana
está iluminada presione y suelte el botón “Light” para
seleccionar el color deseado.Presione el pulsador para
fijar el color deseado.
Selección de tono
La campana tiene diez melodías para la “puerta
principal” seleccionables precargadas. Presione y
suelte el botón “Sync/Music”hasta escuchar la melodía
deseada. Mientras se reproduce la melodía deseada,
presione el pulsador para fijar la melodía seleccionada.
Nota: A cada pulsador se le puede asignar su propia
y única melodía.
Nota: Para escuchar la melodía seleccionada, presione
y suelte el botón “Sync/Music”[“Sincronizar / Música”].
Nota: Todos los modelos de campanillas están dise-
ñados para trabajar hasta con 5 botones pulsadores
(se venden por separado).
VOL +VOL –Light Sync
Music
VOL +VOL –Light Sync
Music
VOL +VOL –Light Sync
Music
Guía de Selección de Tonos
Puerta del frente
Ding-Dong Birthday Celebration
Traditional Westminster Auld Lang Syne
Traditional Whittington Beethoven’s 5th
Bell Whittington We Wish You a Merry Christmas
Short Westminster Star Spangled Banner
Puerta de atrás
Ding
ON
1 2