Heatstore HS2020TXN User manual

Telephone: [phone] Fax: [phone]
Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE.
In the position denoted by the O, the timer continues to run but no power is fed to the heater.
Setting the Timer
Ensure the slide switch on the timer is at the mid position next to the clock symbol Ç .
Rotate the outer ring of the timer in a clockwise direction until the current time is lined up with
the arrow pointer , i.e. if the time the timer is being set is 8 pm, rotate the outer ring until
the number 20 is in line with the arrow pointer.
Set the time the heater is required to run by pulling the segments around the outer ring
forward appropriate to the running period(s) required.
When set, the heater will operate each day during the times programmed.
NOTE the heater must always be plugged into a power socket; the thermostat must be
suitably set to ensure the heater will come on.
If the heater is required to run continuously the slide switch on the timer should be set to
the Oposition.
If it is subsequently required to revert back to timer operation, the slide switch on the timer
should be set to the central (clock) position.
NOTE When using in timer mode, due consideration should be given to the fact that the heater
may come on whilst unattended.
Cleaning the heater
Always unplug the heater from the wall socket and allow it to cool down before cleaning.
Clean the outside of the heater by wiping with a damp cloth and buff with a dry cloth.
Do not use any detergents or abrasives and do not allow any water to enter the heater.
Storing the heater
When the heater is not used for long periods of time it should be protected from dust and
stored in a clean dry place.
ISSUE 2: 0910
ONE YEAR
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
SPECIFICATION: HS2020TXN
RATING: 1800–2000W; 220-240V: ~50/60Hz;
DIMENSIONS: 595w x 420h x 200d mm;
GROSS/NET WEIGHT: 3.9kG/2.9kG
HS2020TXN
Convector Heater
Operating Instructions
HS2020TXN[10Y]instructions 7/9/10 10:09 Page 1

If required, these brackets may also be secured to the wall using the remaining fixing screws
and plastic wall plugs. If this option is chosen it is suggested that the heater is hung on the
upper brackets and the hole positions for the lower brackets is then marked on the wall, prior
to drilling the holes for attachment purposes.
Operation of the heater
NOTE: It is normal when the heaters are turned on for the first time or when they are turned
on after having not been used for a long period of time the heaters may emit some smell and
fumes. This will disappear when the heater has been on a short while.
HS2020TXN Convector heater with switches,
thermostat and timer
Choose a suitable location for the heater, taking into account
the safety instructions above.
Insert the plug of the heater into a suitable socket.
Turn the thermostat knob (

in figure 2) fully in a clockwise
direction to the maximum setting.
Turn on the heating elements by means of the rocker switches
on the side panel (

in figure 2). When the heating elements
are on the switches will illuminate. For maximum heat output
both switches should be on.
When the desired room temperature has been reached, the
thermostat knob should be turned slowly anti-clockwise until
the thermostat is heard to click off and the lights on the
element switches are seen to go out. After this the heater will
keep the air temperature in the room at the set temperature
by switching on and off automatically.
In its minimum (fully anti-clockwise) position, the thermostat
provides a frost guard position. In this position (depending on
the size of the room) the heater will maintain the temperature
above freezing.
This model is also fitted with a 24hr timer which has 96
segments around its circumference, each segment being
equivalent to 15 minutes of time. With the aid of this timer it is
possible to preset the time and duration of the period(s) that it
is desired the heater will operate, in any 24hr period.
Timer Operation
The centre of the timer (figure 3) has a 3 position slide switch.
In the central position (denoted by the clock symbol
Ç ) the
timer will switch the heater on and off at times set by the segments, (see setting the timer,
below).
The position denoted by the Iis a timer override position. The timer will continue to run but
power will be fed continuously to the heater. This enables the heater to be on all the time if
required.
Model covered by these instructions:
HS2020TXN – Convector heater with switches and thermostat
SPECIFICATION – 1800-2000W; 230-240V; 50Hz;
Safety Instructions
DO NOT use the heater unless the feet are correctly attached.
ALWAYS ensure that the heater is placed on a firm level surface. Ensure that the heater is
not positioned close to curtains or furniture as this could create a fire hazard.
MAKE SURE the power supply to the socket into which the heater is plugged is in
accordance with the rating label on the heater and that the socket is earthed.
KEEP the power cord away from the hot body of the heater.
DO NOT use the heater if the power cord is damaged, it must be replaced by a
recognised service agent or a similarly qualified person.
DO NOT position the heater in front of, or immediately below a wall socket.
ALWAYS unplug the heater when moving it from one location to another.
The heater is for indoor use only.
The heater is not intended for use in bathrooms, laundry areas or similar indoor
locations. Never place the heater where it may fall into a bath or other water container.
DO NOT use the heater in areas where flammable liquids are stored or where
flammable fumes may be present.
DO NOT place the heater on carpets having a very deep pile.
DO NOT insert any object through the heat outlet or air grilles of the heater.
WARNING: In order to avoid overheating, do not cover the heater.
Assembly and Installation
Assembly
Before using the heater, the feet (supplied separately in the
carton) must be fitted to the unit. These are to be attached to
the base of the heater using the 4 self-tapping screws
provided, taking care to ensure that they are located correctly
in the bottom ends of the heater side mouldings (see Figure 1).
Wall-mounting
The heater is supplied with 4 sets of fixing brackets, screws and
plastic wall plugs to enable it to be mounted onto a wall if
required. If it is decided to fit the heater to a wall the feet must
be removed.
It must not be positioned in-front of, below a power socket, a
shelf, curtains or any other obstruction. Please refer to the
safety instructions.
Having decided on the location of the heater it is necessary to drill 2 fixing holes 8mm
diameter by 43mm deep at 417mm centres on a horizontal line at a minimum height of
400mm from the floor. Allowance must be made for the final floor covering, carpet etc, and if
any skirting boards are present, the fixing holes must be a minimum of 400mm above the top
edge of the skirting board. Using the plastic plugs and fixing screws provided, attach 2 of the
fixing brackets to the wall. The other pair of fixing brackets must be attached to the base of
the heater using the feet retaining screws so that the brackets project out at the rear of the
heater and space the bottom edge away from the wall.
Figure 1


Figure 3
Figure 2
HS2020TXN[10Y]instructions 7/9/10 10:09 Page 3