Heinner HF-M207SA+ User manual

DOUBLE DOOR REFRIGERATOR
Model: HF-M207SA+
www.heinner.com
•Double door refrigerator
•Net capacity: 204 L
•Energy class: A+

www.heinner.com
1
Thank you for chosing this product!
Please read this instruction manual carefully before using it and kee it for later information
This manual is conceived for ofering you all of the necessary info regarding instalation, using
and maintenance of the machine. For a correctly and safely use of the machine, please, read
this manual before instalation and using.
I. INTRODUCTION
II. PACKAGE CONTENTS
➢Double door refrigerator
➢Instruction Manual
➢Warranty card

www.heinner.com
2
III. SAFETY WARNINGS
1) WARNING―Keep ventilation openings, in the appliance enclosure or in the built-in
structure, clear of obstruction.
2) WARNING―Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.
3) WARNING―Do not damage the refrigerant circuit.
4) WARNING―Do not use electrical appliances inside the food storage compartments
of the appliance, unless they are of the type recommended by the manufacturer.
5) The appliance has to be unplugged after use and before carrying out user
maintenance on the appliance.
6) This appliance can be used by children aged from 8 years and above and persons with
reduce physical sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
7) If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
8) Please recycle the refrigerator according to local regulators for it use flammable
blowing gas and refrigerant.
9) Please according to local regulations regarding disposal of the appliance for its
flammable refrigerant and blowing gas. Before you scrap the appliance, please take off
the doors to prevent children trapped.
10) This appliance is intended to be used in household and similar applications such as:
•staff kitchen areas in shops, offices and other working environments.
•farm houses and by clients in hotels, motels and other residential type
environments.
•bed and breakfast type environments.
•catering and similar non-retail applications.
11) WARNING—Do not store explosive substances such as aerosol cans with a
flammable propellant in this appliance.
12) WARNING—The refrigerant and insulation blowing gas are flammable. When
disposing of the appliance, do so only at an authorized waste disposal centre. Do not
expose to flame.
13) WARNING—When positioning the appliance, ensure the supply cord is not trapped
or damaged.

www.heinner.com
3
14) WARNING—Do not locate multiple portable socket-outlets or portable power
supplies at the rear of the appliance.
15) WARNING—The illuminating lamps must not be replaced by the user! If the
illuminating lamps is damaged, contact the customer helpline for assistance. This
warning is only for refrigerators that contain illuminating lamps.
According to IEC standard
•This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
•Keep all packaging away from children as there is risk of suffocation.
•If you are discarding the appliance, pull the plug out of the socket, cut the
connection cable (as close to the appliance as you can) and remove the door to
prevent children playing from suffering an electric shock or from closing
themselves inside it.
•If this appliance, featuring a magnetic door seals, is to replace an older appliance
having a spring lock (latch) on the door or lid, be sure to make the spring lock
unusable before you discard the old appliance. This will prevent it from
becoming a death trap for a child.
Refrigerant
The refrigerant isobutene (R600a) is contained within the refrigerant circuit of the
appliance, a natural gas with a high level of environmental compatibility, which is
nevertheless flammable. During transportation and installation of the appliance, ensure
that none of the components of the refrigerant circuit becomes damaged. The
refrigerant (R600a) is flammable.
Risk of fire/flammable materials
If the refrigerant circuit should be damaged:
•Avoid opening flames and sources of ignition.
•Thoroughly ventilate the room in which the appliance is situated.
WARNING—Refrigerators contain refrigerant and gases in the insulation. Refrigerant and
gases must be disposed of professionally as they may cause eye injuries or ignition.
Ensure that tubing of the refrigerant circuit is not damage prior to proper disposal.
Electrical safety
1) The power cord must not be lengthened.
2) Make sure that the power plug is not crushed or damaged. A crushed or
damaged power plug may overheat and cause a fire.

www.heinner.com
4
3) Make sure that you can access the main plug of the appliance.
4) Do not pull the main cable.
5) If the power plug socket is loose, do not insert the power plug. There is a risk of electric
shock or fire.
6) You must not operate the appliance without the interior lighting lamp cover.
7) The fridge is only applied with power supply of single phase alternating current of
220~240V/50Hz. If fluctuation of voltage in the district of user is so large that the voltage
exceeds the above scope, for safety sake, be sure to apply A.C. Automatic voltage regulator
of more than 350W to the fridge. The fridge must employ a special power socket instead of
common one with other electric appliances. Its plug must match the socket with ground
wire.
IT IS HAZARDOUS FOR ANYONE OTHER THAN AUTHORISED SERVICE PERSONNEL TO
CARRY OUT SERVICING OF REPAIRS WHICH INVOLVE THE REMOVAL OF COVERS.
TO AVOID THE RISK OF AN ELECTRICAL SHOCK DO NOT ATTEMPT REPAIRS YOURSELF.

www.heinner.com
5
IV. INSTALATION
1. Location
When selecting a position for your unit you should make sure the floor is flat and firm,
and the room is well ventilated. Avoid locating your unit near a heat source, e.g. cooker,
boiler or radiator. Also avoid direct sunlight as it may increase the electrical consumption.
Extreme cold ambient temperatures may also cause the unit not to perform properly.
This unit is not designed for use in a garage or outdoor installation. Do not drape the unit
with any covering.
When installing the unit, ensure that 10 cm of free space is left at both sides, 10 cm at
the rear and 30 cm at the top of the unit. This will allow cold air to circulate around the
wine cooler and improve the efficiency of the cooling process.
2. Reversing the Door Swing
Tools Required: Phillips style screwdriver / Flat blated screwdriver / Hexagonal spanner
1) Remove the right top hinger cover.
2) Remove the screws fixed the top-hinge with cross-slot screwdriver.

www.heinner.com
6
3) Replace the top-hinge and the top-door limit block and the door bearing bush to
the other side.
A. Remove the nut with sleeve. Take off the washer then remove the axes to the other
side and fixed.
B. Remove the door limit block
C. Please taking out another door limit block, with screw mounting to the door
4) Disassemble the screws fixed the bottom-hinge with cross-slot screwdriver.

www.heinner.com
7
Note：the refrigerator-freezer incline angle less 45°.
5) Replace the bottom door bearing bush and the limit block.
6) Replace the bottom hinge to the other side then fix it with screws.
7) Replace the mid-hinge.

www.heinner.com
8
8) Set the bottom door right position, fix the mid-hinge.
9) Replace the top-hinge.
10) Set the top door right position, fix the top-hinge and the cover.
11) Install the four screw caps and two catches to corresponding position.
·Ensure the Appliance is unplugged and empty
·Adjust the two leveling feet to their highest position.
·We recommend you have someone to assist you.

www.heinner.com
9
12) Replace the leveler to the other side and adjust it to make sure the cabinet level.
3. Door Space Requirements
The unit's door must be able to open fully as shown.
W×D≥902×1052mm
W
D
4. Levelling the Unit
To do this adjust the two levelling feet at the front of the unit.
If the unit is not level, the door and magnetic seal alignments will not be covered
properly. Make sure that the foot touches the ground before use. Look down from the
top, clockwise and counterclockwise loosening, tightening.

www.heinner.com
10
Cleaning Before Use
Wipe the inside of the unit with a weak solution of bicarbonate soda. Then rinse with
warm water using a 'Wrung-out' sponge or cloth. Wash the shelves and salad bin in
warm soapy water and dry completely before replacing in the unit. Clean the exterior of
the unit with a damp cloth.
If you require more information refer to the Cleaning section.
Before Using Your Unit
Do not damage the power cord under any condition so as to ensure safety use, do not
use when the power cord is damaged or the plug is worn.
Do not put flammable, explosive, volatile and highly corrosive items in the refrigerator
to prevent damages to the product or fire accidents.
Do not place flammable items near the refrigerator to avoid fires.
This product is household refrigerators and shall be only suitable for the storage of
foods. According to national standards, household refrigerators shall not be used for
other purposes, such as storage of blood, drugs or biological products.
Do not place items such as bottled or sealed container of fluid such as bottled beers and
beverages in the freezer to prevent bursts and other losses.
Before placing any food in your unit, turn it on and wait for 24 hours, to make sure it is
working properly and to allow it time to fall to the correct temperature. Your unit
should not be overfilled.
◆Before Plugging in
You must check that you have a socket which is compatible with the plug supplied with
the unit.
◆Before Turning On!
Do not turn on until two hours after moving the unit.
Interior Accessories
Various glass or plastic storage shelves are included with your appliance - different
models have different combinations.
You should always slide one of the full size glass storage shelves into the lowest set of
guides, above the fruit and vegetable containers, and keep it in this position. To do this,
pull the storage shelf forward until it can be swivelled upwards or downwards and
removed.
Please do the same in reverse to insert the shelf at a different height.
V. BEFORE USING

www.heinner.com
11
In order to make the most of the volume of the fresh food storage compartment and
frozen-food storage compartment, the user can remove one or more shelves, drawers, out of
the appliance, according to your daily use.

www.heinner.com
12
*The picture above is only for reference. The actual configuration will depend on the physical
product or statement by the distributor.
VI. PRODUCT DESCRIPTION

www.heinner.com
13
1. Switching On Your Unit
Setting“Off”： UnitOff
Setting“Min”： Less Cool Temperature
Setting“Med”or“MID”：Normal Operation (adequate for most situations)
Setting“Max”： Coolest Temperature
◆During high ambient temperatures e.g. on hot summer days. It may be necessary to set
the thermostat to the Coolest setting (position “Max”). This may cause the compressor
running continuously in order to maintain a low temperature in the cabinet.
◆For the first time you install your refrigerator, set the thermostat knob at“Med”.
Give your refrigerator time to cool down completely before adding food. It is the best to
wait 24 hours before adding food. The thermostat knob controls the temperature. When
the thermostat control knob is set to OFF, the refrigerator will not be running.
2. Noise Inside the Unit
You may notice that your unit makes some unusual noises. Most of these are perfectly
normal, but you should be aware of them!
These noises are caused by the circulation of the refrigerant liquid in the cooling system.
It has become more pronounced since the introduction of CFC free gases. This is not a
fault and will not affect the performance of your unit. This is the compressor motor
working, as it pumps the refrigerant around the system.
3. Tips for Keeping Food in the Unit
◆Cooked meats/fishes should always be stored on a shelf above raw meats/fishes to
avoid bacterial transfer. Keep raw meats/fishes in a container which is large enough to
collect juices and cover it properly. Place the container on the lowest shelf.
◆Leave space around your food, to allow air to circulate inside the unit. Ensure all
parts of the unit are kept cool.
◆To prevent transfer of favours and drying out, pack or cover the food separately. Fruit
and vegetables do not need to be wrapped.
◆Always let pre-cooked food cool down before you put in the unit. This will help to
maintain the internal temperature of the unit.
◆To prevent cold air escaping from the unit, try to limit the number of times you open
the door. We recommend that you only open the door when you need to put food in or
take food out.
VII. USING INSTRUCTION

www.heinner.com
14
Order
Compartments TYPE
Target storage
temp. [ ℃ ]
Appropriate food
1
Fridge
+2≤+6
Eggs, cooked food, packaged food, fruits and vegetables, dairy
products, cakes, drinks and other foods are not suitable for
freezing.
2
(***)*-Freezer
≤-18
Seafood (fish, shrimp, shellfish), freshwater aquatic products
and meat products (recommended for 3 months, the longer
the storage time, the worse the taste and nutrition), suitable
for frozen fresh food.
3
***-Freezer
≤-18
Seafood (fish, shrimp, shellfish), freshwater aquatic products
and meat products (recommended for 3 months, the longer the
storage time, the worse the taste and
nutrition), are not suitable for frozen fresh food.
4
**-Freezer
≤-12
Seafood (fish, shrimp, shellfish), freshwater aquatic products and
meat products (recommended for 2 months, the longer the storage
time, the worse the taste and nutrition), are not suitable for frozen
fresh food.
5
*-Freezer
≤-6
Seafood (fish, shrimp, shellfish), freshwater aquatic products and
meat products (recommended for 1 months, the longer the storage
time, the worse the taste and nutrition), are not suitable for frozen
fresh food.
6
0-star
-6≤0
Fresh pork, beef, fish, chicken, some packaged processed foods,
etc. (Recommended to eat within the same day, preferably no
more than 3 days). Partially encapsulated processed foods
(non-freezable foods)
To avoid contamination of food, please respect the following instructions:
•Opening the door for long periods can cause a significant increase of the temperature
in the compartments of the appliance.
•Clean regularly surfaces that can come in contact with food and accessible drainage
systems.
•Store raw meat and fish in suitable containers in the refrigerator, so that it is not in
contact with or drip onto other food.
•Two-star frozen-food compartments are suitable for storing pre-frozen food, storing or
making ice cream and making ice cubes.
•One, two and three star compartments are not suitable for the freezing of fresh food.

www.heinner.com
15
7
Chill
-2≤+3
Fresh/frozen pork, beef, chicken, freshwater aquatic products,
etc.(7 days below 0 ℃and above 0 ℃is recommended for
consumption within that day, preferably no more than 2 days).
Seafood (less than 0 for 15 days, it is not recommended to store
above 0 ℃).
8
Fresh Food
0≤+4
Fresh pork, beef, fish, chicken, cooked food, etc. (Recommended to
eat within the same day, preferably no more than 3 days).
9
Wine
+5≤+20
Red wine, white wine, sparkling wine, etc.
Note: please store different foods according to the compartments or target storage
temperature of your purchased products.
•If the refrigerating appliance is left empty for long periods, switch off, defrost, clean,
dry, and leave the door open to prevent mould developing within the appliance.
•Children aged from 3 to 8 years are allowed to load and unload refrigerating
appliances.
4. Change the Light Bulb
WARNING—The illuminating lamps must not be replaced by the user! If the illuminating lamps
is damaged, contact the customer helpline for assistance.
This warning is only for refrigerators that contain illuminating lamps.

www.heinner.com
16
DEFROSTING
NOTE THIS UNIT DOES NOT HAVE AN AUTO DEFROST SYSTEM.
Warning!
•Switching off the appliance.
•To switch off the appliance, turn the temperature regulator to position “0”.
Important: The fridge should be defrosted at least everyone month. During the using
process, if the door was opened frequently or using the appliance in the extreme
humidity, we advise the user to defrost every two weeks.
Cleaning the Interior and the Exterior of the Unit
•Remove all the shelves and the salad bin. To remove the salad bin first remove
the lower door shelf.
•Wipe the inside of the unit with a weak solution of bicarbonate soda and then
rinse with warm water using a“wrung-out”sponge or cloth. Wipe completely
dry before replacing the shelves and salad bin.
•Use a damp cloth to clean the exterior, and then wipe with a standard furniture
polish. Make sure that the door is closed to avoid the polish getting on the
magnetic door seal or inside the unit.
•The grille of the condenser at the back of the unit and the adjacent components
can be vacuumed using a soft brush attachment.
•Dusts behind the refrigerator and on the ground shall be timely cleaned to
improve the cooling effect and energy saving.
•The interior of the refrigerator should be cleaned regularly to avoid odor.
•Check the door gasket regularly to make sure there are no debris.
•Please turn off the power before cleaning, remove all food, shelves, drawers,
etc.
•Clean the door gasket with mild soap and water.
•Use a soft cloth or sponge to clean the inside of the refrigerator, with two
tablespoons of baking soda and a quart of warm water. Then rinse with water
and wipe clean and open the door and dry it naturally before the power is
turned on.
•For areas that are difficult to clean in the refrigerator (such as narrow
sandwiches, gaps or corners), it is recommended to wipe them regularly with a
soft rag, soft brush, etc. and when necessary, combined with some auxiliary
tools (such as thin sticks) to ensure no contaminant accumulation in these
areas.
•Do not use soap, detergent, scrub powder, spray cleaner, etc., as these may
cause odors in the interior of the refrigerator.
•Clean the bottle frame, shelves and drawers with a mild detergent and dry with
a soft cloth.
VIII. CLEANING AND MAINTENANCE

www.heinner.com
17
•Wipe the outer surface of the refrigerator with a soft cloth dampened with
soapy water, detergent, etc., and then wipe dry.
•Do not use hard brushes, clean steel balls, wire brushes, abrasives, such as
toothpastes, organic solvents (such as alcohol, acetone, banana oil, etc.), boiling
water, acid or alkaline items clean refrigerator considering that this may damage
the fridge surface and interior. Boiling water and benzene may deform or
damage plastic parts.
•Do not rinse with water so as not to affect the electrical insulation properties.
Cleaning Tips
Condensation may appear on the outside of the unit. This may be due to a change in
room temperature. Wipe of any moisture residue. If the problem continues, please
contact a qualified technician for assistance.
MAINTENANCE
1. Changing the Internal Light
Lamp replacement by professionals.
2. Care When Handling / Moving Your Unit
Hold the unit around its sides or base when moving it. Under no circumstances should it
be lifted by holding the edges of the top surface.
3. Servicing
The unit should be serviced by an authorized engineer and only genuine spare parts
should be used. Under no circumstances should you attempt to repair the unit yourself.
Repairs carried out by inexperienced persons may cause injury or serious malfunction.
Contact a qualitatively technician.
4. Switching Off for Long Periods of Time
When the unit is not in use for a long period of time, disconnect it from the mains
supply, empty all food and clean the appliance, leaving the door ajar to prevent
unpleasant smells.

www.heinner.com
18
The following simple issues can be handled by the user. Please call the after-sale service
department if the issues are not settled.
Inoperation
Whether the freezer is plugged and connected to power;
Low voltage;
Failure power or tripping circuit
Odor
Odorous foods should closely wrapped;
Whether foods are rotten;
Whether the interior shall be cleaned.
Long-term operation of
compressor
It is normal that refrigerator operates for longer time in
summer when the ambient temperature is higher;
Do not put too much food in the freezer at one time;
Do not put foods until they are cooled;
Frequent opening of refrigerator door.
Illuminating light does not
shine
Whether the refrigerator is connected to power,
whether the illuminating light is damaged.
The refrigerator door can not
be properly closed.
The freezer door is stuck by food packages;
Too much food;
Tilt refrigerator.
Loud noises
Whether the food is leveled, whether the refrigerator is
balanced;
Whether the refrigerator parts are properly placed.
Warm tips:
◆The refrigerator enclosure may emit heat during operation specially in summer, this is
caused by the radiation of the condenser, and it is a normal phenomenon.
◆Condensation: condensation phenomenon will be detected on the exterior surface
and door seals of the freezer when the ambient humidity is large, this is a normal
phenomenon, and the condensation can be wiped away with a dry towel.
◆Buzz: Buzz will be generated by running compressor specially when starting up or
shutting down.
IX. TROUBLESHOOTING

www.heinner.com
19
Try not to open the door too often, especially when the weather is wet and hot. Once you
open the door, close it as soon as possible.
Every now and then check if the appliance is sufficiently ventilated (adequate air
circulation behind the appliance).
In normal temperature conditions, please arrange the thermostat at the middle setting.
Before loading the appliance with packages of fresh food, make sure they are cooled to
ambient temperature.
Ice and frost layer increase energy consumption, so clean the appliance as soon as the
layer is 3-5 mm thick.
If it is the outer condenser, the rear wall should be always clean free of dust or any
impurities.
◆The appliance should be located in the coolest area of the room, away from heat
producing appliances or heating ducts, and out of the direct sunlight.
◆Let hot foods cool to room temperature before placing in the appliance. Overloading
the appliance forces the compressor to run longer. Foods that freeze too slowly may lose
quality, or spoil.
◆Be sure to wrap foods properly, and wipe containers dry before placing them in the
appliance. This cuts down on frost build-up inside the appliance.
◆Appliance storage bin should not be lined with aluminum foil, wax paper, or paper
toweling. Liners interfere with cold air circulation, making the appliance less efficient.
◆Organize and label food to reduce door openings and extended searches. Remove as
many items as needed at one time and close the door as soon as possible.
X. TIPS FOR ENERGY SAVING