Hella VN Setup guide

Installation Instructions and Instructions for Use
These instructions must be read
prior to installation
and use!
Model front-mounted box nova – VN
Operating guidelines
Installation Instructions and Instructions for Use
Table of Contents
Preliminary remarks HELLA Model front-mounted box nova – VN.......................................1
General notes.......................................................................................................................2
CE marking...........................................................................................................................3
Safety instructions ................................................................................................................5
Before installation.................................................................................................................7
Overview: Tools for the installation.......................................................................................8
Overview: Model nova front-mounted box – VN ..................................................................9
Type overview ....................................................................................................................10
Installation in general .........................................................................................................12
Installation of the guide rail insert.......................................................................................13
Installation insect screen rail for integrated moscita insect roller screen ............................14
Commissioning/functional check ........................................................................................15
Motor drive .........................................................................................................................16
Removal .............................................................................................................................16
Handing over report (for the fitter) ......................................................................................17
Handing over report (for the user) ......................................................................................18
Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
1
Preliminary remarks HELLA
Model front-mounted box nova – VN
With this HELLA product you have opted for a high-quality product with a most up-to-date
technology that can nevertheless be easily installed and operated. In these instructions we
describe the basic installation, commissioning and use.
For authorized specialist staff
For the consumer (user)
Please refer to the enclosed installation instructions and instructions for use for outdoor
blinds & exterior Venetian blinds for additional information and notes regarding HELLA
outdoor blinds & exterior venetian blinds.
The following symbols will assist you with the installation or use and require a safety-
conscious conduct:
Attention!
This symbol indicates instructions that, if disregarded, can put the user
in danger.
Attention!
This symbol indicates instructions that, if disregarded, can potentially
result in damage to the product.
This symbol indicates instructions for use or helpful information.
This symbol requires you to act.
Attention!
This symbol indicates a risk of injury or danger to life due to an electric
shock.
This symbol indicates parts of the product, for which you will find
important information in these installation instructions.
This symbol indicates the
cleaning of the product.
This symbol indicates the
maintenance and repair
of the product.
Installation Instructions and Instructions for Use
2 Subject to technical modifications – Date of Issue
September/2020
General notes
Questions
In case of questions concerning the installation or the use of your product, please
consult your authorized specialist shop.
Spare parts/repairs
Spare parts are available at your HELLA specialist shop. Only spare parts that are
approved by HELLA are allowed to be used.
Liability
In case of non-observance of the directions and information given in these instructions
and in case of improper operation or unintended use, the manufacturer shall not accept
any warranty claims concerning any damage to the product. In these cases the liability
for consequential damage to any parts or persons is ruled out as well.
Legal notes
The graphs and texts of these instructions were carefully prepared. We cannot be held
liable for any errors and their potential consequences! Subject to technical modifications
to the product and to these instructions! These instructions include copyrighted
information. All rights reserved! The listed product or brand names are trademarks of the
respective owners.

Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
3
CE marking
The HELLA outdoor blinds / exterior Venetian blinds in the front-mounted system in
combination with the model nova front-mounted box – VN, also in the wind resistant
design, have a declaration of performance as per the construction product ordinance and
when equipped with a motor drive, they also have the declaration of conformity as per the
machinery directive or the directives for electromagnetic compatibility and meet the basic
requirements of the harmonised standard EN 13659 if used as intended. The respective
declarations are deposited with the manufacturers.
For additionally information, especially with regard to the CE marking, please refer to the
enclosed installation instructions and instructions for use for outdoor blinds / exterior
Venetian blinds.
The product mounted meets the requirements only, if
during installation the information and instructions given in these instructions as
well as the information and instructions of the manufacturers of the screws have
been observed,
the product is installed with the recommended type and number of fasteners /
screws.
Installation Instructions and Instructions for Use
4 Subject to technical modifications – Date of Issue
September/2020
CE marking
The HELLA insect screen – moscita, an insect roller screen that is integrated in the
box/recess, is in compliance with the declaration of performance according to the
Construction Products Regulation. In case of proper use, it corresponds to the basic
requirements of the harmonised standard EN 13561. The respective declaration is
deposited with the manufacturer.
The CE identification applies for the delivery status of the product. The product mounted
meets the requirements of the specified standard only, if
during installation the information and instructions given in these instructions as
well as the information and instructions of the manufacturers of the screws have
been observed,
the product is installed with the recommended type and number of
fasteners/screws.
No changes, rebuildings or extensions, with the exception of those described in these
instructions, are allowed with this product. The fixed CE-label expires with any change,
rebuilding or extension.
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach 125
14
LE-ISRO-01-001
EN 13561:2004+A1:2008
Insect roller screen
moscita
Exterior insect screen
Wind resistance class 0
Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
5
Safety instructions
These installation instructions refer to prefabricated elements, that (1) for
100% are made from parts, which are defined by us, and (2) which are
made in manufacturing processes, which are defined by us too; in all other
cases we do not provide any guarantee!
The safety instructions as well as the appropriate instructions must be
read carefully before installation and use. In case of non-observance of
the directions and information given in these instructions and in case of
improper installation and operation or unintended use, the manufacturer
shall not accept any warranty claims concerning any damage to the
product. In these cases the liability for consequential damage to any parts
or persons is ruled out as well.
- Follow the described installation steps and pay attention to
recommendations and notes.
- Keep these instructions in a safe place.
- All installation and removal works, as well as maintenance and repair
works are only allowed to be carried out by authorised and qualified
specialist staff.
- If switching, automatic or radio control devices are used to operate the
units, the information given in the enclosed instructions of the
manufacturer must be observed.
- During operation do not put your hand into or touch movable parts.
- Ensure that clothing or body parts cannot get caught on the unit.
- Observe the regulations for prevention of accidents of the employer's
liability insurance association!
- Before operation check the unit for visible damage. If the unit is
damaged, it should not be used; please consult authorized specialist
staff immediately.
- Risk of injury and accident due to the weight of the product!
- Take safety measures against the danger of squashing, especially
when operating the unit with automatic devices.
- Place the operating switch within sight of the unit, but not near any of
the moving parts.
- Never let children play with the unit.
Danger of suffocation!
Ensure that the foil cannot get into the hands of children. Keep the foil in a
safe place.
Wind load:
Higher load of the channel with strong wind.
Tighten the mounting screws with the appropriate torque.
Installation Instructions and Instructions for Use
6 Subject to technical modifications – Date of Issue
September/2020
Further information and notes, especially with reference to the safe
handling and use of the system, can be found in the accompanying
installation and operating instructions for outdoor blinds & exterior
venetian blinds.

Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
7
Before installation
Check the product immediately for possible shipping damage and for
compliance with the delivery receipt.
If parts are missing or damaged, please consult your supplier immediately.
Check the mounting base and ensure that the mounting material to be
used complies with the given conditions to guarantee proper installation. In
case of doubt, please seek advice from a specialist enterprise for fixing
techniques.
The packaging cardboard box should not be exposed to humidity. To
protect it from rain during transport, it should be covered by a foil.
Carry larger units by two persons. Transport and store the units carefully
to prevent injury of persons and damage to the product.
Remove the packaging material carefully. When using a knife, be careful
not to damage the packaging content and to avoid cuts!
Dispose of the packaging material via recycling.
Caution!
A wrong installation can endanger the user seriously. Please strictly
observe the installation instructions. Close off the place of installation.
When working at higher heights, there is risk of falling. Suitable ascent
supports, scaffoldings and fall protection devices are to be used. Please
make sure that the ascent supports stand solidly and provide a firm grip.
Installation Instructions and Instructions for Use
8 Subject to technical modifications – Date of Issue
September/2020
Overview: Tools for the installation
Battery-powered drill
Depending on the mounting
base (bit holder AW 20, AW
25)
Bit extension
Drill
Drill set
acc. to mounting base
Bit holder
AF 3/8 inch
Level Measuring tape Pin
Torx screwdriver
TX25 - also possible AW20
Allen key
4 mm
Blind rivetting tongs
for ø3.2 mm rivets
Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
9
Overview:
Model nova front-mounted box – VN
Legend
Front-mounted roller
shutter box, closed at
the rear
Covering cap for
guide rail Slat
Inspection cover Lift tape
Header End cap for
Bottom rail Ladder cord
Guide rail Guide rail
Sealing profile Bottom rail Guide rail insert
1
2
5
6
7
8
9
10
11
3
4
12
Installation Instructions and Instructions for Use
10 Subject to technical modifications – Date of Issue
September/2020
Type overview
Front-mounted box nova angular design - VNV
Front-mounted box nova round design - VNR
Front-mounted box nova square design - VNQ
Standard duct dimensions:
PT = 10 mm
PN = 5 mm, 10 mm, 15 mm or 20 mm, special lengths between 5 mm and 80 mm
Legend
PN Plaster flange
PT Plaster base
169
169
140
186
169
140
185
185
152
209
209
170
V 16 V 16XL V 18 V 20
27° 27° 27°
27°
169
177
169
193
185
193
209
219
R 16 R 16XL R 18 R 20
169
169
185
185
Q 16 Q 18

Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
11
Type overview
Front-mounted box nova inclined – VNW
Front-mounted box nova angular design with plaster base - VNP
Front-mounted box nova square design with plaster base - VNQP
Standard duct dimensions:
PT = 10 mm
PN = 5 mm, 10 mm, 15 mm or 20 mm, special lengths between 5 mm and 80 mm
Legend
PN Plaster flange
PT Plaster base
169
169
132
185
185
143
209
209
158
W 16
45°
W 18
45°
W 20
45°
169
169
140
PN
186
169
140
PN
185
185
152
PN
PN
209
209
176
P 16
PT
P 16XL P 18 P 20
PT PT PT
169
169
PN
185
PN
PT PT
QP 16 QP 18
185
Installation Instructions and Instructions for Use
12 Subject to technical modifications – Date of Issue
September/2020
Installation in general
Check the dimensions of the
element and wall opening,
and the dimension of the
window respectively.
Measure the dimension of the
cable duct for the drive
system at the box and
provide the appropriate wall
or window duct.
1. Push the guide rails onto
the struts until the stop
position is reached. Do
not damage the slat
guiding nipples. Make
sure that the guide rails
are at the same height.
2. Screw-down the
countersunk screws to
fix the box to the guide
rail.
3. Hold the unit to the
mounting base, adjust it
and mark the boreholes
through the guide rails
on the mounting base.
Provide the boreholes
according to the
mounting material to be
used. Put the motor
cable through the wall or
window duct already
provided and fix the
element to the structure.
4. Place the covering caps
in the bore holes in the
guide rails.
Legend
Countersunk screw M5 x 16 mm
FB Complete width
LB Clear width
LL Slat length
1.
2.
3.
4.
1
LL
FB
LB
4
Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
13
Installation of the guide rail insert
Press the guide rail insert into
the chamber of the guide rail.
Move the guide rail insert over all slat guiding
nipples towards the top. (A slight bending of
the guide rail insert eases the installation.)
All slat guiding nipples must
be placed inside the guide
rail insert.
The recess areas in the guide rail insert must
be at the bottom side. (Locking with pins of
the guide rail covering cap.)
Installation Instructions and Instructions for Use
14 Subject to technical modifications – Date of Issue
September/2020
Installation insect screen rail for integrated moscita
insect roller screen
The insect screen is already pre-assembled in the plaster base box.
With motor drive
Installation of the insect screen according
to the enclosed installation instructions for
outdoor blinds / exterior Venetian blinds.
(Chapter "Installation guide rail FUP70 /
FUP80 / FUP95
installation insect screen")
With crank handle drive
Do not remove the tear tape from the
guide rail!
Screw down the insect screen guide rail
laterally through the drilled holes to the
guide rail FUP95. Fix the insect screen rail
in such a way that it is flush with the lower
edge of the guide rail.
1 self drilling head screw / bore hole in the
insect screen rail
Legend
Tear tape
Self drilling head screw
ø4.2x22 mm
Installation Easy-Click see accompanying
installation instructions for outdoor blinds /
exterior Venetian blinds.
2
1
14,5

Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
15
Commissioning/functional check
Extend and retract the unit in and out completely. When extending the unit
for the first time, make sure no one is in the operating radius or standing
below the unit.
Make sure that during the later operation the units can be extended freely
and without blockings. Do not extend the unit, if objects or persons are in
the operating radius of the sun protection unit. Please observe the safety
instructions.
After the first extending check the mounting material and the construction
elements for strength.
Automatic control devices or switches, that are not in the operator's field of
vision, may not be used for test runs of motor driven units.
We recommend the use of a test cable for the provisional operation of the
motor.
Check all settings.
Check all screwed connections for tightness.
Double-check the grip of the supports on the mounting base.
Attention!
An insufficient fastening of the mounting brackets can cause the collapsing
of the unit; there is risk of injury or danger to life!
Clean the elements (see maintenance instructions).
Pass these instructions as well as possible instructions of the motor,
switch and control manufacturer on to the user.
Brief the user, whereupon you provide comprehensive information on the
safety and user instructions of the system.
Have the correct design of the system as well as the installation and
briefing with the safety information confirmed in writing (see handover
report).
Installation Instructions and Instructions for Use
16 Subject to technical modifications – Date of Issue
September/2020
Motor drive
With outdoor blinds in the front-mounted
system nova front-mounted box - side by side
the motor drive Geiger E06 is used as
standard. This motor has the advantage that
it references on torque in the upper end
position and thus the package height remains
the same in the long run.
Change of the package / complete height:
Follow the enclosed operating instructions of
the motor manufacturer.
Removal
Switch the unit dead and take safety precautions against unintentional
switching on.
The removal is carried out in reverse order to the installation.
Installation Instructions and Instructions for Use
Subject to technical modifications – Date of Issue
September/2020
17
Handing over report (for the fitter)
Dear Customer,
We are glad that you have opted for a HELLA brand product. Our units are fabricated with
greatest care and many years of experience.
The instructions for use and the installation instructions have been handed over and must
be read before using the product.
An introduction has taken place.
The safety instructions were pointed out.
Your product
Model front-mounted box nova - VN
was installed professionally and handed over
on the .................................................................................................................................... .
Dealer
Name
Place
Postal code
Date
Name
Street
Customer
Place
House number
Signature
Signature
Date
First name
Installation Instructions and Instructions for Use
18 Subject to technical modifications – Date of Issue
September/2020
Handing over report (for the user)
Dear Customer,
We are glad that you have opted for a HELLA brand product. Our units are fabricated with
greatest care and many years of experience.
The instructions for use and the installation instructions have been handed over and must
be read before using the product.
An introduction has taken place.
The safety instructions were pointed out.
Your product
Model front-mounted box nova - VN
was installed professionally and handed over
on the .................................................................................................................................... .
Dealer
Name
Place
Postal code
Date
Name
Street
Customer
Place
House number
Signature
Signature
Date
First name

Installation Instructions and Instructions for Use
HELLA Interior Venetian
Blinds
regulate the lighting in a room
very comfortably, immediately
gracing it with much more
atmosphere.
HELLA Insect screens
and you decide who is allowed
to come in and who isn't.
HELLA Pleated Blind
folds up very compactly and
protects very well against the
sun and nosey glances where
only little space is available.
HELLA Outdoor Blinds
serve for the light regulation,
as view protection, anti-glare
blind and heat protection.
HELLA Front-mounted
Roller Shutter
for more safety and protection
against rain, wind, heat, the
cold, noise, incident light and
nosey glances, also available
for subsequent installation.
HELLA Facade Awning
with toggle catch mechanism
for a lovely facade design with
perfect heat and glare
protection.
For questions, wishes and ideas:
HELLA Infoline +43/(0)4846/6555-0
HELLA Sonnen- und Wetterschutztechnik GmbH
A-9913 Abfaltersbach, No. 125
Phone: [phone]
Fax: [phone]
e-mail: [email protected]fo
Internet: http://www.hella.info