Hellermann Tyton tt230sm User manual

QUICK START GUIDE
TT230SM / TT230SMC
Thermal Transfer Printer

www.Hellermann.Tyton.com | 800.537.1512
2
TT230SM & TT230SMC Quick Start Guide
Unpacking and Inspection
This printer has been carefully packaged to withstand damage during
shipping. Please carefully inspect the packaging and printer upon receipt.
Retain the packaging materials in case you need to reship the printer.
The following items are included in the carton:
If any of the parts listed above are missing, please contact
HellermannTyton Support: 1.800.537.1512
• Printer unit
• Windows USB key drive that
contains drivers and manuals
• Quick Start Guide
• Power cord
• Auto switching power supply
• USB cable
• Printer caddy
• Cardboard ribbon rewind
core (not pictured)

www.Hellermann.Tyton.com | 800.537.1512 3
TT230SM & TT230SMC
Quick Start Guide
Printer Overview
Front View (TT230SMC with cutter shown)
1. Cutter (TT230SMC only) 4. Feed button
2. Ribbon access cover 5. LED indicator
3. Top cover locking tabs 6. SD card slot
7. Media view window
2
1
456 73

www.Hellermann.Tyton.com | 800.537.1512
4
TT230SM & TT230SMC Quick Start Guide
Printer Overview
Interior View
1. Ribbon rewind hub
2. Ribbon rewind gear
3. Gap sensor (receiver)
4. Internal media holder
5. Media holder lock switch
6. Gap sensor (transmitter)
7. Print head
8. Ribbon supply hub
9. Top cover support arm
10. Media guide adjustment knob
11. Black mark sensor
12. Platen roller
1
2
7
8
9
10
11
12
3
4
5
6

www.Hellermann.Tyton.com | 800.537.1512 5
TT230SM & TT230SMC
Quick Start Guide
Printer Overview
Rear View
1. Ethernet interface
2. USB interface
3. Centronics interface
4. RS-232C interface
5. Power jack socket
6. Power switch
7. Paper entrance chute
1 2
7
3 4 5 6

www.Hellermann.Tyton.com | 800.537.1512
6
TT230SM & TT230SMC Quick Start Guide
Printer Setup
Initial Setup
1. Place the printer on a flat, secure surface.
2. Make sure the power switch is off.
3. Plug the power cord into the AC power cord socket at the rear of the
printer, then plug the power cord into a properly grounded power
outlet.
4. Connect the provided USB cable to the printer and then connect
to your computer.
Ethernet RJ-45
interface
USB interface
Centronics interface
RS-232C
interface
Power
Supply
Power
Switch
Plug

www.Hellermann.Tyton.com | 800.537.1512 7
TT230SM & TT230SMC
Quick Start Guide
Opening the Top Cover
1. Open the top cover by pulling the locking tabs (located on each side)
towards the front of the printer. Lift the top cover to the maximum
open angle.
2. Once fully open, the top cover support arm, at the right rear of the
printer, will engage to hold the top cover open.

www.Hellermann.Tyton.com | 800.537.1512
8
TT230SM & TT230SMC Quick Start Guide
Loading Ribbon
For a video tutorial on loading the ribbon,
visit www.hellermann.tyton.com
1. While the top cover is open and supported, open the ribbon access
cover.
Note:
The ribbon access cover can be opened while opening the top cover. The ribbon access cover
can be closed while top cover is open or closed.
2. Insert the cardboard ribbon rewind core (included with every ribbon)
into the right side of the rewind hub by aligning the notches on the
right side and mounting onto the spokes.

www.Hellermann.Tyton.com | 800.537.1512 9
TT230SM & TT230SMC
Quick Start Guide
3. Insert the cardboard ribbon rewind core into to the left side of the
supply hub by aligning the notches on the left side and mounting onto
the spokes.
4. Install the ribbon by securing the female notches at the ends of the
ribbon core to the mounting spokes on the ribbon supply hub.

www.Hellermann.Tyton.com | 800.537.1512
10
TT230SM & TT230SMC Quick Start Guide
5. Unravel the ribbon leader (blue or silver), and stick it onto the cardboard
rewind core.

www.Hellermann.Tyton.com | 800.537.1512 11
TT230SM & TT230SMC
Quick Start Guide
6. Turn the ribbon rewind gear until the ribbon leader is thoroughly wound
and the black ribbon covers the print head.
7. Close the ribbon access cover and the top cover.

www.Hellermann.Tyton.com | 800.537.1512
12
TT230SM & TT230SMC Quick Start Guide
Loading Labels
1. Open the main printer cover by
moving the locking tabs toward the
front of the printer while lifting up
the cover.
2. Gently separate the green internal
media holder and pull and lock to
the sides.
3. Install label roll onto the caddy.
4. Feed labels into the back of the
printer, as shown
5. Adjust the label guides (see picture footnote).
6. Close the printer cover.
2
3 4

www.Hellermann.Tyton.com | 800.537.1512 13
TT230SM & TT230SMC
Quick Start Guide
Adjust the label guides using the small gear to the right side. The label
stock should fit between the two guides, but not too tightly.
Label stock should move easily between the guides.
Correct Setup
5
TT230SM
TT230SM Label stock feeds out the front of the printer, as shown.
TT230SMC
TT230SMC Label stock feeds through the cutter, as shown.

www.Hellermann.Tyton.com | 800.537.1512
14
TT230SM & TT230SMC Quick Start Guide
Closing the Printer Cover
While holding the top cover, gently push in the support arm to disengage.
The cover should close easily once the arm is disengaged.
Turn on the power to the printer.
The light on the top of the printer, located by the “Feed” button, should
turn green.
Congratulations! You’ve successfully completed the initial
printer setup!

www.Hellermann.Tyton.com | 800.537.1512 15
TT230SM & TT230SMC
Quick Start Guide
Installing the Printer Driver
In order to operate the printer, the printer driver software must be installed
on a computer connected to the printer.
Driver Installation
1. Plug the USB key into an available USB port on your computer;
the key / stick contains the printer driver software.
2. Select “Open folder to view files” from the pop-up window.

www.Hellermann.Tyton.com | 800.537.1512
16
TT230SM & TT230SMC Quick Start Guide
3. Double click on HT719M3 to open the driver installer.
4. Click Next.

www.Hellermann.Tyton.com | 800.537.1512 17
TT230SM & TT230SMC
Quick Start Guide
5. Click Finish
6. Confirm that “Install printer drivers” is selected, and click Next.

www.Hellermann.Tyton.com | 800.537.1512
18
TT230SM & TT230SMC Quick Start Guide
7. Select TT230SM from the model list. Select the same driver
for TT230SM or TT230SMC.
Click Next.
8. Select or highlight USB001 as your specified port and click Next.

www.Hellermann.Tyton.com | 800.537.1512 19
TT230SM & TT230SMC
Quick Start Guide
9. The default printer name will appear as TT230SM. If you are installing a
TT230SMC printer, you can manually enter TT230SMC.
Click Next.
10.Click Finish. Driver installation is complete. The printer is now ready to
use.

HellermannTyton North American Corporate Headquarters
7930 N. Faulkner Rd, PO Box 245017, Milwaukee, WI 53224-9517
Phone: [phone], Fax: [phone]
email: [email protected], www.hellermann.tyton.com
TS16949, ISO 9001, and ISO14001 certied
HellermannTyton Canada
Unit #4, 205 Industrial Parkway North, Aurora, Ontario L4G 4C4 Canada
Phone: [phone], Fax: [phone]
email: [email protected]
HellermannTyton Mexico
Anillo Periferico Sur 7980 Edicio 6A, Parque Industrial Tecnologico II
Santa María Tequepexpan, Tlaquepaque, Jalisco, Mexico 45601
Phone: [phone], Fax: [phone]
email: [email protected]
ISO 9001 certied
© HellermannTyton Corporation
TT230QSTART, Printed 05.2015
For additional printer installation tips and videos,
visit www.hellermann.tyton.com
This site also offers information how to print using different label types,
including continuous, die-cut and partially pre-printed.
If you have additional questions and concerns,
contact HellermannTyton technical support at 800-537-1512.
General Warranty Policy
HellermannTyton products are warranted to be free from defects in material and workmanship at the time
sold by us; but our obligation under this warranty and that of the seller is limited to the replacement of the
product, and neither we nor the seller are bound by any other warranty, expressed, implied or statutory.
Under no circumstances are we or the seller liable for any loss, damage, expenses or consequential damages
of any kind arising out of the use or inability to use these products. All are sold with the understanding that
the user will test them in actual use and determine their adaptability for the intended uses.
Desktop Printer Warranty
The HellermannTyton Performance Guarantee assures the performance of our desktop thermal transfer
printers for a period of 2 years from the date of purchase from an authorized HellermannTyton distributor.
This Guarantee is provided to all customers, on the understanding that they are operating in according
relevant HellermannTyton installation and care instructions provided with each printer.
For complete information on our printer warranty, visit www.hellermann.tyton.com/warranty.