Helo Rocher DES User manual

ELECTRIC SAUNA HEATER:
1102 –70 –040517
1102 –105 –040517
230V –240V 1N~ / 2~
230V 3~
400V –415V 3N~
CONTROL PANEL:
1601 –31 (RA –31) Trend)
1601 –33 (RA –33) Premium Wifi
314 SKLT 68-3 A
Installation and User Manual Rocher DES
REWARD YOURSELF

Contents Page
1.Quick instructions for use of the sauna heater 3
1.1. Check before taking a sauna bath 3
1.2. Operation of the sauna heater controls 3
2.Information for users 3
2.1. Sauna room 3
2.2. Heating the sauna 3
2.3. Recommended sauna room ventilation 4
2.4. Installing the sensor near a supply air vent 4
2.5. Ceiling installation of the sensor 4
2.6. Sauna heater stones 5
2.7. If the sauna heater will not heat up 6
2.8. Preparing for sauna heater installation 6
2.9. Installation 6
2.10. Sauna heater safety clearances 6
2.11. Sauna heater safety clearances 7
2.12. Preparing for piling the stones 8
2.13. Installing the support for heating elements 9
2.14. Connection of the sauna heater to the mains 10
2.15. Electric heating toggle 10
2.16. Locating the connecting box for the connection cable in the sauna room 11
2.17. Remote controlling 11
2.18. Door switch 12
2.19. Wiring diagram 13
2.20. Principle image when 1601 - 31 (RA - 31 Trend) is used as control panel 14
3.Rocher DES spare part list 15
4.ROHS 16
Figures and tables
Figure 1 Rekommended sauna room ventilation 4
Figure 2 Safety clearances 7
Figure 3 Preparing for piling the stones 8
Figure 4 Installing the support for heating elements 9
Figure 5 Location for the connection box 11
Figure 6 Remote control connection 11
Figure 7 Installing the door switch 12
Figure 8 Door switch connection 14
Figure 9 Connection of a door switch with a fault indicator light 12
Figure 10 Wiring diagram for the sauna heater 13
Figure 11 Principle image 14
Table 1 Safety clearances 6
Table 2 Connection cable and fuses 10
Table 3 Rocher DES spare parts list 15
Installation and User Manual Rocher DES
2

1. Quick instructions for use of the sauna heater
1.1. Check before taking a sauna bath
1. The sauna room is suitable for taking a sauna bath.
2. The door and the window are closed.
3. The sauna heater is topped with stones that comply with the manufacturer's recommendations, the heating elements are
covered with stones, and the stones are piled sparsely.
NOTE! Ceramic rocks are not allowed.
The heater's main switch is located at the bottom of the heater, on the right side as seen from the front.
The main switch is marked with a 0 –1 sticker.
1.2. Operation of the sauna heater controls
Refer to the specific control panel operating instructions.
Rearrange the sauna stones at least once a year and replace any weathered stones. This enhances air circulation
between the stones, which extends the useful life of the thermal resistors.
If you encounter any problems, please contact the manufacturer's warranty service shop.
For additional information about enjoying a sauna bath, please visit our website at : www.tylohelo.com
2. Information for users
This appliance may not be used by children aged less than eight years, by persons with reduced physical, sensory or
mental capabilities, or by persons lacking experience and knowledge regarding its operation only if such have been
given instructions on the safe use of the device and the risks involved. Children must not be allowed to play with the
appliance or to clean and service it without supervision. (7.12 EN 60335-1:2012)
2.1. Sauna room
The walls and ceiling of a sauna room should be thermally well insulated. All surfaces that store heat, such as tiled and
plastered surfaces must be insulated. It is recommended to use wooden panel cladding inside the sauna room. If there
are heat storage elements in the sauna room, such as decorative stone, glass etc., note that these elements may extend
the pre-heating period even though the sauna room is otherwise well insulated (see page 6, section 2.8. Preparing for
sauna heater installation).
2.2. Heating the sauna
Before turning the sauna heater on, make sure the sauna room is suitable for taking a sauna bath. When heated for the
first time, the sauna heater may emit some odour. If you detect any odour while the sauna heater warms up, disconnect
the sauna heater briefly, and air the room. Then turn the sauna heater back on.
You should turn the sauna heater on roughly an hour before you plan to take a sauna bath, so that the stones have time
to heat up properly and the air warms up evenly in the sauna room.
If you encounter any problems, please contact the manufacturer's warranty service shop.
Pleasant, smooth sauna bath temperature is about 70 °C.
Do not put any objects on the sauna heater. Do not dry clothes on the sauna heater or anywhere in its vicinity.
Installation and User Manual Rocher DES
3

2.3. Recommended sauna room ventilation
Figure 1 Rekommended sauna room ventilation
1. Sauna room 3. Electric sauna heater 5. Exhaust flue or channel
2. Washroom 4. Exhaust valve 6. Door to the sauna room
7. A ventilation valve can be installed here to be kept closed while the sauna is heated and during bathing.
Inlet vent can be positioned in the A zone. Make sure the incoming fresh air will not interfere with (i.e. cool down) the
sauna heater's thermostat near the ceiling.
The B zone serves as the incoming air zone, if the sauna room isn't fitted with forced ventilation. In this case, the exhaust
valve is installed min 1m higher than the inlet valve.
DO NOT ISTALL INLET VALVE WITHIN ZONE C, IF THE SAUNA HEATER'S CONTROL THERMOSTAT IS LOCATED
IN THE SAME ZONE.
2.4. Installing the sensor near a supply air vent
The sauna room air should be exchanged six times in an
hour. The diameter of the supply air pipe should be
between 50 and 100 mm.
A circular air supply vent (360°) must be
installed at least 1000 mm away from the sensor.
An air supply vent with a flow-directing panel
(180°) must be installed at least 500 mm away from
the sensor. Air flow must be directed away from the
sensor.
2.5. Ceiling installation of the sensor
In ceiling installation, a 5-mm hole must be drilled to the sensor case to allow any condensed water to drain.
Do not spray water directly towards the sensor or splash water at it with a sauna scoop.
Installation and User Manual Rocher DES
4
360° 1000 mm
180° 500 mm
Sensor
Sensor
ø5 mm
55
4
4
2
1
1
1
A
7
A
min
500 mm
6
3
B
3
B
C
C
C
C A
1000 mm

2.6. Sauna heater stones
Quality stones meet the following requirements:
-Sauna stones should withstand heat and heat variation caused by vaporisation of the water thrown on the
stones.
- Stones should be rinsed before use in order to avoid odour and dust.
- Sauna stones should have an uneven surface to supply a larger surface for the water to evaporate from.
- Sauna stones should be large enough, measuring about 100–150 mm to allow good ventilation between the stones.
This extends the useful life of the heating elements.
- Sauna stones should be piled sparsely in order to enhance ventilation between the stones. Do not bend the heating
elements together or against the frame.
- Rearrange the stones regularly (at least once a year) and replace small and broken stones with new, larger stones.
-Empty the stone compartment regularly, at least once a year in private use, remove small and broken stones and
replace them with new ones.
-In commercial use this operation must be performed at least every second month.
- Stones are piled so that they cover the heating elements. Do not, however, pile a large heap of stones on the
heating elements. For a sufficient amount of stones refer to Table 1 on page 6. Any small stones in the package of
stones must not be piled on the sauna heater.
- The warranty does not cover defects resulting from poor ventilation caused by small and tightly packed stones.
-Structural clay tiles are not allowed. They may cause damage to the sauna heater that will not be covered
by the warranty.
- Do not use soapstone as sauna rocks. Any damages resulting from this will not be covered by the stove
warranty.
- Do not use lava stone as sauna rocks. Any damages resulting from this will not be covered by the stove
warranty.
-DO NOT USE THE HEATER WITHOUT STONES.
Installation and User Manual Rocher DES
5

2.7. If the sauna heater will not heat up
If the sauna heater will not heat up, please check that:
- the power is on;
- the main fuses of the sauna heater are intact;
- is there any error messages on the control panel. In case of an error message on the control panel,
please refer to the control panel instructions.
THE PERSON INSTALLING THE SAUNA HEATER SHOULD LEAVE THESE INSTRUCTIONS AT THE PREMISES
FOR THE FUTURE USER.
2.8. Preparing for sauna heater installation
Check the following before installing the sauna heater.
- The ratio of the heater's input (kW) and the sauna room's volume (m3). Volume recommendations are presented in
Table 1 on page 6. The minimum and maximum volumes must not be exceeded.
- The sauna room height must be a min. of 1900 mm.
- Uninsulated and masonry stone walls extend the preheating time. Each square metre of plastered ceiling or wall surface
adds 1.2 m3to the sauna room's volume.
- Check page 8 Table 2 for a suitable fuse size (A) and the correct diameter of the power supply cable (mm²) for the
sauna heater in question.
- Conform to the specified safe clearance around the sauna heater. Please refer to page 6.
- There should be enough room around the control panel for maintenance purposes. Also a doorway can be considered
as a maintenance area.
2.9.Installation
Follow the safety clearance specifications on page 6 and 7 when installing the sauna heater.
The sauna heater is a floor-standing model. The base must be solid, because the sauna heater weighs about 120 kg.
The sauna heater is levelled by the adjustable legs.
The sauna heater is fixed on the floor from its legs by the provided metal fasteners (2 pcs). This will keep the safety clear-
ances intact during use.
Mounting of the sauna heater to the wall or the sauna benches available as an accessory (metal fastenings. S-ZH 58,
0043272).
Walls or ceilings must not be clad with fibre-reinforced plaster board or other light-weight cladding, because they may
cause a fire hazard.
Only a single sauna heater is allowed per sauna room.
2.10. Sauna heater safety clearances
Table 1 Safety clearances
Out-
put
Sauna room
Heater minimum clearances
Amount of
stones
kW
Volume
Height
From
side to
wall
A
mm
From
front to
sauna
bench
D
mm
To ceil-
ing
mm
In kg, approx.
min.
m³
max.
m³
min. mm
6.8
5
9
1900
60
60
770
100
10.5
9
15
1900
60
60
770
100
Installation and User Manual Rocher DES
6

2.11. Sauna heater safety clearances
Corner and wall installations: The OLET 28 sensor is installed 40 mm from the ceiling on the centre line of the heater on a
wall. Alternatively, the sensor can be installed on the ceiling above the centre of the heater –see 'middle installation' for instruc-
tions. The heater must be secured to the floor or the sauna bench structure in order to keep the safety distances the same.
Middle installation: If the sauna heater is installed further
than 60 mm off a wall or a corner, the installation method is
always middle installation. The heater must be attached to
the benches or to a similar structure using a wall support.
The OLET 28 sensor is always installed on the ceiling.
Figure 2 Safety clearances
Installation and User Manual Rocher DES
7
1900
60
mm
60 770
40 *)
1130
A D F
H
mm
60
60 425 mm
*)
OLET 28
OLET 28
1900
60
mm
60
770
AA
F
H
OLET 28
OLET 28 sensor position in a
ceiling installation above the
heater within the 515 mm
diameter.
Wall support
Heater mounting point to
wall or sauna bench
This is an accessory
Wall support
Heater mounting point to
wall or sauna bench
This is an accessory
Wall support Heater
mounting point to wall
or sauna bench
This is an accessory
Fixing the sauna heater
on the floor. NOTE fixing
of two (2) legs
*) Absolute measurement! (must not be exceeded
or undershot)
Safety clearances between the bottom of
the sauna heater and a wall.
Adjustable leg
Floor fastener
Hearters leg
Metal fastener

2.12. Preparing for piling the stones
Removing of the supporting bars to pile the stones
Unscrew the bars' mounting screws (2 pcs).
Lift the support bar's locking plate up from its
normal position.
Lift off the support bars.
Pile stones up to the Helo marker.
Reinstall the support bars.
Install the support bars as above in the reversed order.
Pile the stones so that they cover the heating elements.
For specific instructions refer to section 2.6 Sauna heater stones.
Figure 3 Preparing for piling the stones
Installation and User Manual Rocher DES
8

2.13. Installing the support for heating elements
Note that heating element support should always be used in order to
prevent the heating elements from being bent into each other or out sideways.
Installation of the heating element support:
Pile in stones up to halfway of the provided space. Position the
support so that the heating elements stay between the openings.
Tilt the support and press the pivots at each end of the support to
the grooves in the inside of the heater's vertical beams, one end at a
time. The support for heating elements should stay levelled.
Push the pivots at one end of the support to the
grooves in the vertical beams.
Press the pivots at the other end of the support to the
grooves in the heater's vertical beams.
Subsequently, pile in stones up to the upper edge so
that they cover the heating elements.
Figure 4 Installing the support for heating elements
Installation and User Manual Rocher DES
9

2.14. Connection of the sauna heater to the mains
The sauna heater must be connected to the mains by a qualified electrician and in compliance with current regulations.
The sauna heater is connected with a semi-permanent connection. Use H07RN-F (60245 IEC 66) cables or a
corresponding type. Other output cables (signal lamp, electric heating toggle) must also adhere to these
recommendations. Do not use PVC insulated cable as a connection cable for the sauna heater.
A multipolar (e.g. 7-pole) cable is allowed, if the voltage is the same. In the absence of a separate control current fuse, the
diameter of all cables must be the same, i.e. in accordance with the front fuse.
The connecting box on the sauna wall should be located within the minimum safety clearance specified for the sauna
heater. The maximum height for the connection box is 500 mm from the floor. See page 9 Location the connection box
See page 11.
If the connection box is located at over 500mm distance from the heater, the maximum height is 1000mm from the floor.
Power
kW
Sauna heater’s
connection cable
H07RN –F/ 60245
IEC 66
mm²
400V 3N~
Fuse
A
Sauna heater’s
connection cable
H07RN –F/ 60245
IEC 66
mm²
230V 3~
Fuse
A
Sauna heater’s
connection cable
H07RN –F/ 60245
IEC 66
mm²
230V 1 N~ / 2~
Fuse
A
6,8
5 x 1,5
3 x 10
4 x 4
3 x 20
3 x 6
1 x 35
10,5
5 x 2,5
3 x 16
4 x 6
3 x 35
----------
--------
Table 2 Connection cable and fuses
NOTE: Controlling the lights in the sauna with the circuit board is only possible with resistive loads (incandescent light
bulbs). The circuit board relay cannot withstand capacitive loads (switched-mode power supply units). If the lighting
fixtures in the sauna have transformers, for example LED or halogen lamps, the stove circuit board's relay control must be
fitted with a separate relay or contactor for controlling the lights.
Sauna heater insulation resistance:
The sauna heater heating elements may absorb moisture from air, e.g. during storage. This may cause leakage currents.
The moisture will be gone after a few heating sessions. Do not connect the heater power supply through a ground fault
interrupter.
However, adhere to the effective electrical safety regulation when installing the sauna heater.
2.15. Electric heating toggle
Electric heating toggle applies to homes with an electric heating system.
Sauna heater has connections (marked N-55) for controlling the electric heating toggle. Connectors N-55 and the heating
elements are simultaneously live (230V). The sauna heater thermostat also controls the heating toggle. In other words,
home heating turns on once the sauna thermostat cuts power off the sauna heater.
Installation and User Manual Rocher DES
10

2.16. Locating the connecting box for the connection cable in the sauna room
A = Specified minimum safety clearance
1. Recommended location for the connecting box
2. Silumin box recommended in this area.
3. This area should be avoided. Always use a silumin box.
In other areas, use a heat-resisting box (T 125 °C) and heat-resisting cables (T 170 °C). The connection box must be
clear of obstacles. When installing the connection box to zones 2 or 3, refer to the instructions and regulations of the
local energy supplier.
200 mm
A A
500 mm
3.
2.
500 mm
1
3.
2.
Figure 5 Location for the connection box
2.17. Remote controlling
The heater can be turned on by pressing the power button or via a normally open contact.
Remote control can be pulsed, or it can always remain on.
NOTE: Heater regulations require door switches if the heater is turned on from outside of the sauna room.
Accessory 0043233 Door switch set.
The remote control system can be supplemented by adding a signal light to indicate when the remote control system
has switched the heater on.
If the indicator light signals a fault caused by leaving the sauna door open for more than five minutes by flashing
quickly, then the heater will be turned off automatically. The heater runs according to the time set in the control panel.
The sauna heater can also be turned off remotely.
Figure 6 Remote control connection
Installation and User Manual Rocher DES
11
C1C2C3
+12V DC
Heater
adapter
circuit board
OLEA 102
Remote control.
Indicator light
12 VDC max. 20 mA

2.18. Door switch
The door switch refers to the switch on the sauna door. This switch complies with regulations. Public and private saunas
must have a door switch, i.e. saunas where the heater can be switched on from outside the sauna, e.g. using an On/Off
button or a similar method.
If the door is opened before the heating sequence is started, (pre-set heating) automatic use (remote use) is disabled after
one minute. The door must be closed and the function restarted from the control panel.
If the door has been left open for more than five minutes while the heater is on, the heater is automatically turned off.
The heater can be turned on again from the control panel after the door is closed. The fault indicator light, if installed, will
start flashing. See installation instructions below.
Door switch instructions for installation and connection
The door switch is installed outside the sauna room on the upper edge of the door, at least 300 mm from the inner corner.
The switch part is installed on the door frame and the magnet is installed on the door. The distance between the switch and
the magnet is 18 mm.
The door switch wiring is connected to the adapter circuit board OLEA 102. LiYY 4 x 0.25 mm² can be used as the cable.
Helo model number 0043233, SSTL 8260371 is recommended to be used as the door switch.
Figure 7 Installing the door switch
Figure 8 Door switch connection Figure 9 Connection of a door switch with a fault indicator light
Installation and User Manual Rocher DES
12
Connection box
Door switch
Magnet for the door
B1 B2
OLEA 103
Adapter circuit board
OLEA 102
Black Brown
B1 B2 B3
OLEA 103
B1 = +12 VDC
B3 = ( - )
Adapter circuit board
OLEA 102
Fault
indicator light
12 VCD max. 20 mA
Black Brown
Door switch Min. 300 mm Junction box
Magnet
on the door
Max. 18 mm

2.19. Wiring diagram
Figure 10 Wiring diagram for the sauna heater
Installation and User Manual Rocher DES
13
354 SKLT13 C
12 3 6
4 5
6,8-10,5kW230V 3~
L1 L2 L3
N
12 3 6
4 5
6,8 kW230V 1N~/ 2~
L1 / N L2
12 3 6
4 5
6,8-10,5kW400 V 3N~
L1 L2 L3
X1
X2
OLEA 103
Light
X13
X14
X11
X12 Sec/
NTC
Door
Switch
Ext
Switch
Ext
NTC
Control
panel
1 2 3 4
A 1 2 3 4 B 1 2 3 C 1 2 3 D 1 2
X5
X6
X3
X4
X9
X10
X7
X8
X17
X18
X15
X16 Aux 0
RJ45
Sec/
NTC
Door
Switch
Ext
Switch
Ext
NTC
2
3
1
1.
2.
N N N 55
9.3.
K1
T1 AH
F1
T3,15 AH
F2
K2
Control
panel
1. Syöttö / Nätet / Stromnetz / Power input / Stroomaansluiting / Puissance absorbée / Leejasjauda / Toide/
Wejœcie zasilania / /Входное напряжение Napájení / Ingresso alimentazione
2. Sähkölämmityksen vuorottelu/ El.förregling avannan el. förbrukare/ Interrupteur du chauffageélect rique/
contact designal / Signal kontakt / signál kontaktu / Signal contact / signaalcontact / Signal kontakts / сигнала
Elektrikütte kontakt / Wisselschakelaar elektrischeverwarming, / Sterowanie ogrzewaniem elekt rycznym
3. Saunavalo / Bastu belysning / Saunabeleuchtung / Sauna light. / Sauna icht max100W. / Ampoule du s auna/
Sauna swiatlamax / Pirtsapgaismojums maksimali / Saunalamp / / Osvìtlení saunyСауна свет. макс
4. Ohjauskeskus/ Styrpanel / Steuergerät / Control panel. / Panneau decommande/ Bedieningspaneel
Panel decontrol / Table decommande/ Vadibaspults / JuhtimiskeskusПульт управления / Panel sterujący /
Vadibas pults / Juhtimiskeskus / Пульт управления
e5. Tuntoelin / Sensor/ Fühler / Capteur/ Sensor / Czujnik/ / Senzor / Érzékelő / Датчик
6. Ovikytkin / Dörrströmbrytare / Doorswitch / Türschalter / Interrupteurde porte / Interruptor d e puerta /
Дверной выключатель / Rozłącznik na drzwiach
7. /Kauko-ohjaus Fjärrkontroll / Remotecontrol / Femsteuerung / Télécommande / Control remoto /
/Дистанционное управление Zdalne sterowanie Dálkové ovládání Afstandsbediening/ / /
8. Tuntoelin extra / Sensorextra / Fühler extra / Capteurappoint / Dodatkowy czujnik/ Дополнительный датчик /
e / Senzor extra / Érzékelő extraSensor extra /9. Tuuletin / Fläkt / Ventilator/ Fan max, 100W / Ventilateur / Ventilador /Вентилятор не более 100 Вт Wentylator
4.
5.
6.
7.
8.
Aux 1
Aux 2

2.20. Principle image when 1601 - 31 (RA - 31 Trend) is used as control panel
Figure 11 Principle image
Installation and User Manual Rocher DES
14
Heater
4
3
2
1
4
3
2
1
A 1 2 3 4
Heater
Terminal block
Heater
A1 Yellow
A2 Green
A3 Red
A4 Black
Adapter circuit
board OLEA 102
Control panel
1601 - 31
Sensor cable
Sensor OLET 28
Limiter
1= Blue
2= White
3= Red
4= Yellow
Adapter circuit
board OLEA 102
Principle image
Sensor OLET 28
Silicone 4 x 0,25 mm²
4 x 0,15 mm²
Control panel
1601 - 31
Input
230V –240V 1N~ / 2~
230V 3~
400V –415V 3N~
NOTE!
See more detailed
installation
instructions
in the control panel
operating
instructions
Heater

3. Rocher DES spare part list
Table 3Rocher DES spare parts list
Part
Part nummer
part name
Rocher 70 DES
Rocher 105 DES
1
7712000
Cable clamp
1
1
2
5916324
Circuit board OLEA 103
1
1
3
5716203
Finder relay
2
2
4
7801711
Fuse 1 AT
1
1
4
7801710
Fuse 3,15 AT
1
1
5
7817536
Fuse holder
2
2
6
6101741
Rocker switch OAAA 2
1
1
7
7306008
Rubber cover for rocker switch
1
1
8
5207770
Heatin element SEPC 199
2267W/230V
3
9
5207771
Heating element SEPC 200
3500W/230V
3
11
5916323
Adapter circuit board
OLEA 102
1
1
Installation and User Manual Rocher DES
15

4. ROHS
Ympäristönsuojeluun liittyviä ohjeita
Tämän tuotteen käyttöiän päätyttyä sitä ei
saa hävittää normaalin talousjätteen
mukana, vaan se on toimitettava
sähkö- ja elektroniikkalaitteiden kierrätykseen
tarkoitettuun keräyspisteeseen.
Symboli tuotteessa,
käyttöohjeessa tai
pakkauksessa tarkoittaa sitä.
Valmistusaineet ovat kierrätettävissä merkintänsä
mukaan. Käytettyjen laitteiden
uudelleenkäytöllä, materiaalien hydöyntämisellä
tai muulla uudelleenkäytöllä teet arvokkaan teon
ympäristömme hyväksi.
Tuote palautetaan ilman kiuaskiviä ja verhouskiviä
kierrätyskeskukseen.
Tietoa kierrätyspaikoista saat
kuntasi palvelupisteestä.
Anvisningar för miljöskydd
Denna produkt får inte kastas med
vanliga hushållssopor när den
inte längre används. Istället ska den
levereras till en återvinningsplats
för elektriska och elektroniska apparater.
Symbolen på produkten,
handboken eller
förpackningen refererar till detta.
De olika materialen kan återvinnas enligt
märkningen på dem. Genom att återanvända,
nyttja materialen eller på annat sätt återanvända
utsliten utrustning, bidrar du till att skydda vår
miljö.
Produkten returneras till återvinningscentralen
utan bastusten och eventuell täljstensmantel.
Vänligen kontakta de kommunala myndigheterna
för att ta reda på var du hittar närmaste
återvinningsplats.
Instructions for environmental protection
This product must not be disposed with
normal household waste at the end of
its life cycle. Instead, it should be
delivered to a collecting place for the recycling
of electrical and electronic devices.
The symbol on the product, the
instruction manual or the
package refers to this.
The materials can be recycled according to the
markings on them. By reusing, utilising the
materials or by otherwise reusing
old equipment, you make an important
contribution for the protection of our environment.
Please note that the product is returned to the
recycling centre without any sauna rocks and
soapstone cover.
Please contact the municipal administration
with enquiries concerning the recycling place.
Hinweise zum Umweltschutz
Dieses Produkt darf am Ende seiner Lebens-
Dauer nicht über den normalen Haushaltsabfall
Entsorgt werden, sondern muss an einem
Sammelpunkt für das Recycling von elektrischen
und elektronischen Geräten abgegeben werden.
Das Symbol auf dem produkt, der
Gebrauchsanleitung oder der
Verpackung weist darauf hin.
Die Werkstoffe sind gemäß ihrer Kennzeichnung
wiederverwertbar, Mit der Wiederverwendung,
der stofflichen Verwertung oder anderen Formen
der Verwertung von Altgeräten leisten Sie einen
wichtigen Beitrag zum Schutze unserer Umwelt.
Dieses Produkt soll ohne Steine und
Specksteinmantel an dem Sammelpunkt für
Recycling zurückgebracht werden.
Bitte erfragen Sie bei der Gemeindeverwaltung
die zuständige Entsorgungsstelle.
Installation and User Manual Rocher DES
16